Part # NL102
Manufacturer Code PNP192L
Alternate Part #'s PNP192L, GAD-75-6170, PNP192L-EACH
Pool Cove 48" Section - Peel N' Place Closed Cell Foam
Much easier to install and more dependable than sand coves, Peel & Stick Pool Cove has an adhesive backing for quick, easy installation and will extend the life of your liner for years!
A cove is needed to keep the weight of the water in the pool liner from causing it to balloon out under the bottom of the pool wall. Previously, pool cove had to be hand built using tons of sand or dirt. Liner failures due to cove washout were all too common. Corrosion occurred rapidly where metal components, at the bottom of the pool, came in contact with moisture in the sand or dirt.
*Extends Pool Life
*Installs in Minutes
*Can not be washed out
*Helps prevent corrosion
*Eliminates liner failures due to cove washout
Click on Your Pool Size Below to Save On Complete Cove Packages
|# of Cove Strips Needed for Full Set|
|Pool Size||# of Strips Required|
So only ONE cove strip ( 48”) costs $20 each?? And If I need 18 for my pool it would cost me $360???? For simple foam? Ridiculous. Did I get this wrong?
We will need to review the single pricing, I located the Pool Cove Peel & Stick 48" 22-pack - NL102-20 https://www.inyopools.com/Products/00100016060866.htm
For a 24’x52”do you need just the one cove molding for $19.99? Is the price listed for a 24’ pool?
You will need to purchase a quantity of 19 of the peel and stick cove to fit in a 24' round pool.
are the ends of the cove pieces angled to fit the various radius's of different pool diameters, or do the they gaps between the pieces when they are butted together?
Hi, Dan. Tape is used to hide the grove caused by attaching two coves together.
Hello I have In-Ground pool with liner and cement on floor, do I need purchase cove for my pool?? Also do I need purchase bottom floor foam for my pool? Thanks.
Hi, Larisa. No, you do not. These are only meant to be used in above ground pools.
When putting pool cove in do you need adhesive? And how many 4 ft pcs for a 18 round?
Hi, Scott. You do not need an adhesive for the Peel and Stick Pool Cove, 14 is required for an 18' Round Pool.
What is the delivery price to Russia, Moscow order for 12 round pool?
Hello, We would need your address, with zip code and part you want to order (NL102) to give this information to our shipping specialist to draw up a quote with shipping based off where your location is. Any duties, taxes and fees are your responsibility.
If the cove is 48" long, shouldn't I only need 4-48" pieces for a 16' round pool?
The dimensional information of the 16' Round pool is based on a measurement of the diameter of the pool. Since the circumference of the pool is much larger, you will need 13 of the pool coves for your size pool.
When installing the Peel and Stick Pool Cove, do I need to seal it using tape to the Gorilla floor?
Hi Matt, This cove does have an adhesive strip on the back of the cove which would secure it to the pool wall. No tape or adhesive would be needed on the bottom of the cove to secure to Gorilla floor.
More than 8 hrs
Screwdriver, Nut Drivers, Socket Set
I was and have replaced the liner but the peal and stick even after cleaning didn't stick.
The pool ordinarily had a dirt cove. Perhaps since the metal was not new cause an issue. I went back to dirt cove. Unfortunately you only have 30 day from order not recipe to return. If anyone wants to buy them they are brand new in the box. I'm trying to think of uses such as wall bumpers for kids or parking stops for cars in a garage.
(5 out of 5 stars) A must have product
Reviewed By: engine8 from Boston ()
Pros: easy to use, quick to install
Cons: none that I found
If you are still using sand to build up the sides, this is the product for you. Its sooooo easy to use and it builds the perfect edge for the liner. You don't even have to think about it, just peal of the the protective tape to reveal the sticky back and stick to the side of the pool. It even has a groove cut out for the bottom channel so it seems to be impossible not to get the perfect berm that is so important for the liner to fit properly.