$28.48

Qty:

Details

Top

Part # 88-265-1005

Product Description

Product Description
AquaMend is a hand-mixable, specialty epoxy putty for repairs to damp, wet areas and underwater surfaces. After mixing, it forms a polymer compound that may be applied underwater (either fresh or salt water) and will bond tenaciously to substrates such as fiberglass, concrete, ceramic, glass, metal, wood, and many plastics. Each stick contains pre-measured portions of base and activator throughout — no measuring or mixing tools are necessary. The consistency (like modeling clay) eliminates drips and runs, facilitates adhesion to the substrate, and allows the material to be shaped and formed as needed before curing begins. After 60 minutes the application can be drilled, sawed, sanded, carved, and painted. AquaMend cures to an off-white color. Suitable for interior or exterior use, it is resistant to chemicals, water, and temperature extremes. AquaMend contains no solvents or VOCs. It is non-flammable and releases no noxious fumes. It won't shrink or pull away. The unused portion stays fresh for future use when saved in its original package.

 

Performance Data*

  • SHELF STABILITY AT 75°F (24°C): - 24 months minimum
  • SHORE D HARDNESS AT FULL CURE (24 hrs): 70
  • LAP SHEAR TENSILE STRENGTH:
    • On steel (1" x 1" x 1/16"): 900 lbs (6.2 MPa)
    • On fiberglass (1" x 1" x 1/16"): 500 lbs (3.5 MPa)
  • COMPRESSIVE STRENGTH: 8,000 psi (55 MPa)
  • DENSITY: 15.8 lb/gal, 1.9 gm/cm3 
  • SHRINKAGE: <1%
  • NON-VOLATILE CONTENT: 100%
  • ELECTRICAL RESISTANCE: - 30,000 megohms-cm
  • DIELECTRIC STRENGTH: 300 volts/mil
  • TEMPERATURE LIMITS:
    • Continuous: -40° to 250°F (-40° to 121°C)
    • Intermittent: -40° to 300°F (-40° to 149°C)
  • CHEMICAL RESISTANCE:
    • Resistant to hydrocarbons, ketones, alcohols, esters, halocarbons, aqueous salt solutions and dilute acids and bases.
  • NOT INTENDED FOR STRUCTURAL APPLICATIONS

*Not to be used for specification purposes

Top

?     Asked on 7/23/2014by Guest

Can this product be applied underwater to the bottom of a boat hull that is in saltwater?
 Reply

A  Answered on 7/23/2014 by InyoPools Product Specialist Patrick P.

Yes this can be used on a boat haul and the Aquamend is resistant to salt water, so this should do the trick.
 Reply


?     Asked on 4/25/2015by Jeff

Has this been used to seal leaks in concrete baptistry's?
 Reply

A  Answered on 4/28/2015 by InyoPools Product Specialist Robert M.

Hello Jeff - The Aquamend Epoxy can be used in a concrete baptistry.
 Reply


?     Asked on 12/6/2015by Dan

Hi, is this product suitable for repair of a crack in the bottom of a hot tub? It will be underwater @ 105 degrees, thanks!
 Reply

A  Answered on 12/7/2015 by InyoPools Product Specialist Lennox H.

Hi Dan, The AquaMend Underwater Repair Epoxy Putty can be used to repair a crack in an hot tub surface and can with stand temperatures up to 250°.
 Reply


?     Asked on 1/4/2016by james

will this work in a 9ft deep pool inground in the cold water my drain popped off and I need to put it back on
 Reply

A  Answered on 1/15/2016 by InyoPools Product Specialist Joe S.

Good day James, attached is a link to Aquamends Technical data sheet. With their specifications and contact information.
 Reply


?     Asked on 5/21/2016by Jeremy

Can this putty be powder coated? Is the cure time lower if it's not being applied underwater or in a damp envirnment? What is the maximum gap it could fill? Thanks.
 Reply

A  Answered on 5/28/2016 by InyoPools Product Specialist Lennox H.

Hi Jeremy, The AquaMend Epoxy Putty can be powder coated, this product can only be used damp, wet or underwater applications.  It does not state the maximum application per stick.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
1 Ratings
5 star:
 
(1)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)