Part # 8350TIE
Alternate Part #'s 016033, RAY016033
Raypak is proud to introduce its new heat pump product line. Every Raypak heat pump now comes standard with a titanium heat exchanger. The Professional Series and Classic Series heat pumps have been designed to meet the exacting needs of the pool and spa professionals. Raypak offers a feature rich entry level heat pump, the Professional Series, which provides rock solid performance at an affordable price.The Classic Series offers a top of the line product for the customer who demands the best. And finally, for those big jobs and high end pools, the Raypak 8350ti is the heat pump of choice.
8350ti Specifications:
BTU Output: 133,000
C.O.P: 5.5
Compressor: Scroll
Refrigerant: R-410A
Voltage: 208/230V - 1 Phase: 60 HZ
Maximum Circuit Ampacity: 44
Maximum Breaker Size: 60 Amps
Electrical Input: 7.0 kw
Heat Exchanger: Titanium
Water Flow: 15-60 GPM
WARRANTY EXCLUSIONS
This Limited Warranty does NOT apply;
1. if the product has been moved from its original place of installation, or if the original
owner no longer owns the property where the original installation was made;
2. if the product is not properly installed with a pool or spa by a qualified licensed installer in
accordance with applicable local codes and ordinances, good trade practices, and the
manufacturer’s installation instructions;
3. if the rating plate(s) or serial number(s) are altered or removed;
4. if the product is modified in any way, or non-factory authorized accessories or other
components are used in conjunction with the product;
5. to damage, malfunctions or failures resulting from failure to properly install, operate or
maintain the product in accordance with the manufacturer’s instructions;
6. to damage, malfunctions or failures from abuse, act of nature, accident, fire, flood, freeze,
lightning or the like;
7. to damage, malfunctions or failures resulting from [or due to] connected system control
devices;
8. performance problems caused by improper sizing of the heater or electric service
voltage, wiring or fusing;
9. use of any attachment, including any energy saving device not authorized by the
manufacturer.
10. to damage, malfunctions or failures from misuse or neglect, including but not limited to,
freeze-ups, operating the heater with the cabinet door off, having flow restrictions or
obstructions between the heater outlet and the pool/spa, or not maintaining a proper
chemical balance (PH level must be between 7.4 and 7.8 and total alkalinity between 100
and 150 PPM. Total dissolved solids (TDS) must be no greater than 3000 PPM)
when I search for a rheem 835 ti Raypak heatpumps come up in the search results. Are they the same company?
Reply
Yes the Rheem and Raypak heaters are the same company and exact same units, some retailers purchase and sell under the Rheem name while others use the Raypak name.
Reply
i purchased the raypak 8350 and the technitions just left. The heater shows heating , but so quiet doesnt seem like compressor has kicked on. Is this possible or has the compressor not kicked on. In fact, its cold @ 52 degrees and the pool temp showed a drop in pool water temp ,but heating light lite....
Reply
If the air outside the heat pump is too cold, the heat pump will not operate. The actual point at which the unit will cease operating due to low temperature varies. Current weather conditions, the amount of sunlight reaching the heat pump, and the installation quality are primary contributors to this event. The shutdown will occur near or around 50°F (10°C).
Reply
any reason i cannot reduce immediately from 2" to 1 1/2" piping in/out of this unit?
my current system is all 1 1/2" @ approx. 50 GPM & 8 ft/s & would prefer to keep all valving, fittings & runs the same size. only flow spec i see in the manual for this unit is 15 - 60 GPM, no velocity band stated.
Reply
Hi. The plumbing can be reduced to 1-1/2 inches, the GPM is the velocity rating of the unit.
Reply
I want to buy a heat/cool heat pump and I want to control the water temp and pump remotely through wifi. Can this unit be controlled this way? Do you sell the controls to do this?
Reply
Hello, yes this can be controlled by an automation system, but the system you need is based on the relay that you have.
Reply
