Display Local Ps-4 Datecode 0311 & Later - GLX-LOCAL-PS-4

$542.99

IN STOCK
FREE SHIPPING

Part # 2807-04

By Hayward Pool Products


Details

Top

Part # 2807-04

Warranty 1-Year Manufacturer Defect Warranty from the Date of Purchase.

Manufacturer Code GLX-LOCAL-PS-4

Dimensions 6-3/8" X 5-1/4"

Alternate Part #'s GLXLOCALPS4, _GLX-LOCAL-PS-4, GOLGLX-LOCAL-PS-4

Product Description

DISPLAY LOCAL PS-4 DATECODE 0311 & LATER

Top

?     Asked on 4/28/2021 by Roger

My display will just beep like it wants to power up but won't. Is this the correct replacement?

 Reply

A  Answered on 5/1/2021 by InyoPools Product Specialist Patrick P.

Hi Roger, Do you know if you have P4, PS4, P8 or PS8? Is this the indoor controller or the controller at the power supply? If it is the controller indoors then can you operate all of your equipment still from the outdoor power supply? Trying to determine if your indoor board or outdoor board is the culprit. Please click the reply link below to reply.
 Reply


?     Asked on 10/28/2020 by pat sullivan

I have a Hayward Ps-4 Controller that worked just fine. I shut power off for 5 days due to a heater core leak. Now only beeps intermittent and the display flashes a blank screen. I can control the function of the controller with my wireless remote. Is there a bad backup battery? Remote works everything but the beeping and the blank screen continues?
 Reply

A  Answered on 10/29/2020 by InyoPools Product Specialist Joe S.

Hello Pat, attached is the Consumer Troubleshooting Guide that would help troubleshoot the issues.
 Reply


?     Asked on 10/16/2020 by kris

I have Goldline Aqualogic control. 12 years old, it works but the screen faded to the point that it is barely visible. Is this the right replacement for display?
 Reply

A  Answered on 10/16/2020 by InyoPools Product Specialist Joe S.

Good day,To better assist you with getting the correct unit. Please send us a photo of the board, the controller and the display. You can send the information using our Online Support.
 Reply


?     Asked on 3/26/2020 by

Need spacer pegs for Hayward Aqua Logic control panel, Hayward part # GLX-STDLFFPAK20
 Reply

A  Answered on 4/1/2020 by InyoPools Product Specialist Lennox H.

Hi. The Display Standoff - GLXSTDOFFPAK20 is available for purchase. 
 Reply


?     Asked on 2/23/2020 by Paul Alfano

is the correct flow switch for a GLX Local PS 4 board flow switch GLX FLO RP?
 Reply

A  Answered on 2/24/2020 by InyoPools Product Specialist Lennox H.

Hi, Paul. Yes, it is. 
 Reply


?     Asked on 8/17/2019 by Joe

My display has been fading for a long time and now nothing displays. Is it this or the main board?
 Reply

A  Answered on 8/17/2019 by InyoPools Product Specialist Lennox H.

Hi, Joe. If the system runs fine with no other issues, you will need just to replace the Local Display. 
 Reply


?     Asked on 6/8/2019 by Elias

I heve a gold line aqualogic control on my system and lately the timer has been erratic and some times turns the pump on and others doesn't start it and frequently I have to re-programe it because it is slow some times in the time and other time on the date,I wonder if you can tell me what is wrong with it and what do I to do .-Should I have to change the control?
 Reply

A  Answered on 6/10/2019 by InyoPools Product Specialist Patrick P.

Hi Elias, What you have explained is an indication that your AquaLogic Main PCB needs to be replaced.
 Reply


?     Asked on 3/20/2019 by FARSHAD

Hi, I have a AQL-TW-RF-PS-4 which is table mount control system. Recently is not showing data on screen and message says is not communicating with base, but all bottoms are functional. When I take that and get close to RF antenna, will start reading data on screen with 2 feet distance working fine and after that I would loses data on screen. As I said still I can turn on and off everything but cannot read display. Is there any issue with RF antenna or Remote panel? Thank you
 Reply

A  Answered on 3/24/2019 by InyoPools Product Specialist Lennox H.

Hi, Farshad. The Wireless Antenna Base - AQL2BASERF will be the issue based on the info you're having.
 Reply


?     Asked on 3/8/2019 by Kevin

I have a 2005 Wall Mount model AQL-WW-RF-PS-4 that has a gone bad, is the glx local ps-4 a replacement?
 Reply

A  Answered on 3/12/2019 by InyoPools Product Specialist Steve M.

Kevin, the replacement for your AQL-WW-RF-PS-4 would be the PS-4 Wireless Wall Mount - White - AQL2-WW-RF-PS-4. You can find it by clicking the link here: http://www.inyopools.com/Products/02100001004873.htm
 Reply


?     Asked on 1/26/2019 by Judy Howard

My base receiver is not responding
 Reply

A  Answered on 1/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Judy. You will need to confirm that it's getting power. If it is, then it will need to be replaced. 
 Reply


?     Asked on 11/7/2018 by Joe

I have a Hayward Ps-4 Controller that worked just fine. I shut power off for about three weeks then turned back on to winterize. The Local Display like the one in your photo now only beeps intermittent and the display flashes a blank screen. I can control function of the controller with my wireless remote. Able to do that I am assuming the main board is ok and the local display maybe bad. What are your thoughts??
 Reply

A  Answered on 11/9/2018 by InyoPools Product Specialist Lennox H.

Hi, Joe. There is a good chance just the local display is bad. To confirm, use the Troubleshooting Guide which has instructions on pages 21-24. 
 Reply


?     Asked on 7/11/2017 by Dan

Hi, Seems Main Circuit board is out, for my Goldline Aqua Logic PS-4 system. Had to replace it a few yrs back after lightning. This time the display was off, but after reset power breakers...it displayed info/status. Original pump replaced last yr (from you). When press Filter button to start,it shows it's on,BUT it isn't. Local pool service guy says it's the main board out again. He's ordered one. Panel number down in lower right is DP70003D-1. Which item part would you have recomm'd? Thnx.
 Reply

A  Answered on 7/13/2017 by InyoPools Product Specialist Patrick P.

Hi Dan, Yes that is an indication that your Main AqualLogic PCB is bad. Here is a link to the Main AquaLogic PCB Board that you will require.
 Reply


?     Asked on 6/28/2017 by Chet Novak

does the GLX-local-PS4 RUN THE TIME THE FILTER AND CARETAKER OPO UP HEADS
 Reply

A  Answered on 7/2/2017 by InyoPools Product Specialist Lennox H.

Chet. Yes, all the programming and setting are stored in the Local Display. 
 Reply


?     Asked on 4/3/2017 by GabrielGarcia Correa

Hi my name is Gabriel Garcia I have a chlorinator control model 2807-04 , About 6 months ago the system start delay the time . I get into the configuration to set the correct time but the next day I find 2 or three hours delay. About a month ago the timer in the controller do not run. The rest of the function works, but without the timer my system is a totally manual system. I want to know if there are some part of the board that I can replace or if I need to replace the whole unit
 Reply

A  Answered on 4/7/2017 by InyoPools Product Specialist Andy O.

Hello Gabriel- It sounds like your AquaLogic Main PCB is going bad. I wouldn't be able to tell you if there is a part on the board itself to fix this issue, but here is a link to the PCB Circuit Board AquaLogic Version 2.6 - GLXPCBMAIN.
 Reply


?     Asked on 11/29/2016 by jim carneiro

I need the plastic pins that hold the GLX control panel in the main panel box. They are about 2" long and keep the control panel steady. The pins plug into the mother board from the back of the display panel.
 Reply

A  Answered on 11/30/2016 by InyoPools Product Specialist Alan M.

Hello Jim- Unfortunately the pins are not a replacement part we have available. You can try contacting Hayward directly at 1-800-657-2287. A representative there should be able to assist you.
 Reply


?     Asked on 2/28/2016 by Gina

I have a gold line remote that looks just like this one on your site but mine is white. It has stopped working, I keep getting the message "base receiver not responding" does that mean I need to replace the base unit or would replacing the remote itself fix the problem?
 Reply

A  Answered on 3/3/2016 by InyoPools Product Specialist Lennox H.

Hi Gina, Replacing the remote may not solve your problem. I would recommend following the steps on page 7-8 in the Wireless Remote Display Installation/Operation Manual. If those step doesn't work contact Hayward Tech Support for assistance.
 Reply


?     Asked on 8/18/2015 by susanna limon

I have a aqua logic remote control and the battery no longer works without being plugged into an outlet. I need to order just the battery for this product I can't find it on your site goldlin control p/n 014008A-1 4.8 v @ 700 ni-CD. It looks like four AA batteries wrapped in a white plastic with a red and black wires coming out thanks
 Reply

A  Answered on 8/24/2015 by InyoPools Product Specialist Joe S.

Hello Susanna this unit is Not available for replacement.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

None

The display screen on my controller was non-responsive.

Written on 5/26/2021 by Guest

The pool would come on and off as usual but I could not get any information from the display screen. I went to my local pool supply store and troubleshot my problem. They did not have a replacement on hand so I ordered one from INYO. The face of the controller pops right off, there was one cable from the motherboard to the controller's face. I turned off the system at the breaker box, for safety's sake. Then I unplugged the old one and plugged in the new one and popped the new face on.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 0  out of 5 stars)
0 Rating
5 star:
 
(0)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)