AquaRite Display PCB (OEM) GLX-PCB-DSP

$157.99

IN STOCK
FREE SHIPPING

Part # 2807-11

By Hayward Pool Products

  5 Average  

Details

Top

Part # 2807-11

Manufacturer Code GLX-PCB-DSP

Dimensions 3.27" W x 3" L

Alternate Part #'s G1-066604K-1, G1066604K1, GLX-PCB-DSP, GLXPCBDSP, 43-150-1028, GLD-451-1009, GOLGLX-PCB-DSP

Product Description

Replacement display board for the Hayward AquaRite & AquaTrol salt system.

Top

?     Asked on 6/22/2022by Inyo Visitor

Is your product a replacement for my 2009 Goldline Controls P/N: G1-066604K-1?

 Reply

A  Answered on 6/22/2022 by InyoPools Product Specialist Craig C.

Hello.  The AquaRite Display PCB (OEM) GLX-PCB-DSP is the Hayward OEM replacement Display Board for part number Goldline Controls G1-066604K-1
 Reply


?     Asked on 8/3/2021by Jay Martin

My Aqua Rite Goldline model G1-066604F-1 display board is completely blank and no longer produces chlorine. Can i buy a new display or do i have to buy the "Main board" as well
 Reply

A  Answered on 8/3/2021 by InyoPools Product Specialist Stephen B.

Thank you for contacting Inyo Pools, Have you tried checking the fuse in the box?
 Reply


?     Asked on 6/24/2021by John Jones

I just replaced this part and my salt level is reading a bit higher than before. Is this normal?
 Reply

A  Answered on 6/25/2021 by InyoPools Product Specialist Danny R.

I actually just did this on Monday and had the same issue.  My issue was I was adding salt before because I was getting a low salt reading on a bad cell / board.  So when I replaced the board and the cell I had a higher salt reading due to the fact that it was now reading off the new correct board and cell instead of a bad cell / board, and had too much salt in my pool.
 Reply


?     Asked on 5/19/2021by Darlene

Hi, board seems to be running as there is vibration within the unit, but the display is not lighting up. Would a neww display be needed or a whole new board?
 Reply

A  Answered on 5/19/2021 by InyoPools Product Specialist Patrick P.

Hi Darlene, 9 times out of 10 we find that both the Display board and Main AquaRite PCB Board will need to be replaced.
 Reply

  • Commented on 5/19/2021 by Product Owner

    How often is it simply a matter of a blown resistor?

     Reply

    • Commented on 5/20/2021 by InyoPools Product Specialist Patrick P.

      Sometimes it is a bad resistor normally one of the legs on the resistors will be broken so I would visually inspect your resistor. If you do replace the resistor you have to solder it on so it is a little bit more of a professional repair. We also find that in most cases when soldering a new resistor the repair will last 1-2 years and then any future repairs last shorter, so eventually a new board will be required.
       Reply


?     Asked on 5/10/2021by Mark

Is this part a direct replacement for gold line controls g1-066604f-1

 Reply

A  Answered on 5/11/2021 by InyoPools Product Specialist Patrick P.

Hi Mark, Yes this is a direct replacement for your g1-066604f-1 AquaRite display board
 Reply


?     Asked on 1/1/2021by bill

Hello, is this part compatible with 132604 REV: E Thanks
 Reply

A  Answered on 1/18/2021 by InyoPools Product Specialist Megan C.

Yes, the AquaRite Display PCB (OEM) - GLX-PCB-DSP is compatible with 132604 REV: E
 Reply


?     Asked on 12/3/2019by suhail

will this replace this model? G1-0666D6
 Reply

A  Answered on 12/4/2019 by InyoPools Product Specialist Lennox H.

Hi. Suhail. Unfortunately, I'm unable to confirm using the info provided. Please provide the model name of the panel that you have.
 Reply


?     Asked on 10/24/2019by Donald Kaupp

Is the 2009 version of this part a direct replacement for the 2008 version?
 Reply

A  Answered on 10/25/2019 by InyoPools Product Specialist Lennox H.

Hi, Donald. This Display PCB - GLX-PCB-DSP will work with version prior to 2008 and current. 
 Reply


?     Asked on 9/15/2019by George

I have a Goldline Aqua-Rite T15 system over 12 years old. My display shows 0.00 and I can step through the display. AL reading is AL-5 but I can not change it to AL=0. Slide switch has no effect. I have only the power on LED illuminated. All voltages are present and correct. What is your diagnosis?
 Reply

A  Answered on 9/18/2019 by InyoPools Product Specialist Lennox H.

Hi, George. The AL reading is unable to be changed. If the cell amps which is the 3rd reading is zeros, the issue is the cell.
 Reply


?     Asked on 7/21/2019by Bern

Is this piece a replacement for the gold line controls pn: 132604 rev F?

 Reply

A  Answered on 7/21/2019 by InyoPools Product Specialist Lennox H.

Hi, Bern. Yes, Display PCB (OEM) - GLX-PCB-DSP is the correct replacement. 
 Reply


?     Asked on 5/23/2019by Fred

If I read it correctly, I have a Gold Line P/N Q1-066012F-1 REV A. What is the replacement?
 Reply

A  Answered on 5/23/2019 by InyoPools Product Specialist Steve M.

Hi, Fred. In order to locate the correct replacement board, we will need to know the controller name. For example, AquaRite, AquaLogic, etc.
 Reply

  • Commented on 5/24/2019 by Product Owner

    Did you receive my earlier reply? It is an Aqua Rite by Gold Line.
     Reply

  • Commented on 5/23/2019 by Product Owner

    AQUA RITE, GOLDLINE CONTROLS, 12X24 Pool,
     Reply


?     Asked on 8/10/2018by Richard McCoy

Is my display # G1-066604F1 compatible with the new main board # G1-066604K1 for my Hayward goldline controls
 Reply

A  Answered on 8/11/2018 by InyoPools Product Specialist Lennox H.

Hi, Richard. Yes, those boards are compatible.  
 Reply


?     Asked on 11/16/2017by R Pru

Is the part 132604 the same as GLX-PCB-DSP? My display board doesn't have the gold tabs on the bottom left. Is this replacement set to a T-15 by default? Thank you
 Reply

A  Answered on 11/16/2017 by InyoPools Product Specialist Kevin G.

The first number you mentioned is our product code for the part. The second code you mentioned is the manufacturer's code. Therefore, these two codes both reference the same part that is in question. This board doesn't get set to anything by default, it is based on your system. So when you receive this, you'll have to set it to your board.
 Reply


?     Asked on 9/24/2017by gerald cox

i have a hayward salt water generator t9 every thing is working correctly but have no generator light or super chlorinator is this the display panel
 Reply

A  Answered on 9/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Gerald Cox. The issue could be the Main PCB - GLX-PCB-RITE. In order to confirm, you will have test the Display Board. Instructions are available on Page 11, Step H of the AquaRite Troubleshooting Guide.
 Reply


?     Asked on 7/23/2017by Charles

The display window on my Goldline Aqua Rite unit is half dark now and thus unreadable. Could that be a problem with PCB or do you think that it is just the display?
 Reply

A  Answered on 7/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Charles. It sounds like it's just the display because it's not completely blank. You can use the Step H on page 11 of the AquaRite Troubleshooting Guide to be sure.
 Reply


?     Asked on 7/15/2017by Rocco

My display show’s numbers, my power and generating lights come on and off. I do hear clicking when they do come on. Help... Thanks
 Reply

A  Answered on 7/16/2017 by InyoPools Product Specialist Lennox H.

Hi, Rocco. Based on what you've described, the Main PCB is the issue. You can either replace it with the OEM - GLXPCBRITE or Aftermarket - PL7100 Main PCB if compatible. 
 Reply


?     Asked on 6/21/2017by mike matusek

how do I know if this part is bad?unit makes chlorine ,but te percentage changes daily. set at20 ,drops to 7 or goes up to 30%
 Reply

A  Answered on 7/29/2017 by InyoPools Product Specialist Alex V.

Mike, The display typically does not affect the readings. You can use this troubleshooting guide to diagnose the issue. 
 Reply


?     Asked on 6/2/2017by ddurmon

Is the part 132604 the same as GLX-PCB-DSP?
 Reply

A  Answered on 6/3/2017 by InyoPools Product Specialist Patrick P.

Yes this is the GLX-PCB-DSP display board and is the same as the 132604
 Reply


?     Asked on 5/22/2017by Display of PCB?

My Aquarite T-15 is controlled by a Aqualink RS8. The actual PPM is not matching what the display is showing on my RS8 even after calibration. My Aquarite is only showing 2100PPM so I get a constant 'Check Cell' message. I've recalibrated the Aquarite by removing the four remote wires on that connect my Aqaurite to the RS8, and then recalibrating. I'm only able to get the read out to show correctly for about a week or so, then it drops back down to 2100. Is this my display or main PCB?
 Reply

A  Answered on 5/29/2017 by InyoPools Product Specialist Lennox H.

Hi. I would recommend getting the water tested, if your salt level is about 500 ppm above what the controller is reading then you will need to add salt to your pool.
 Reply


?     Asked on 5/10/2017by Bob

I have a Goldline Aqua-Rite T-15 system that is more then 10 years old. My display is showing 9900 for salt and only the power light is on. There is no light, clicking or any sound associated with the cell generator turning on when cycled to auto or super clorinate. Is this a main board problem or display board problem?
 Reply

A  Answered on 5/11/2017 by InyoPools Product Specialist Patrick P.

Bob, this sounds like the main board, I would suggest the After Market PL7100 AquaRite Main PCB Board
 Reply


?     Asked on 4/12/2017by Inyo Visitor

My power light is on continuously but no other lights are on. The cell is clean. I went through the trouble shooting procedures in the manual and all voltages and ohms were correct and it said to change this board. Would the indication of only the power light on be a likely symptom?
 Reply

A  Answered on 4/12/2017 by InyoPools Product Specialist Scott W.

Yes, it sounds like the display board is going bad.
 Reply


?     Asked on 2/25/2016by Lauri

My salt pool isn't generating salt. The display is working but it won't turn off. No other lights are working on the display. Should I replace the display & circuit board. System is @ 7 years old.
 Reply

A  Answered on 3/3/2016 by InyoPools Product Specialist Lennox H.

Hi Lauri, I would start with the Aqua Rite Main PCB (GLX-PCB-RITE). With the PCB replaced if the lights are still not coming on then replace the Aqua Rite Display PCB.
 Reply


?     Asked on 8/15/2015by Inyo Visitor

My display board is GOLDLINE CONTROLS PN: 066604F-1. Will board GLX-PCB-DSP work as a replacement?
 Reply

A  Answered on 8/16/2015 by InyoPools Product Specialist Lennox H.

Hi, The Aqua Rite PCB Display Board will be the correct replacement for the Goldline Salt Generator.
 Reply


?     Asked on 7/21/2015by Howard Shipley

My display board is a 2008 model with P/N G1-066604G-1. Will this board work as a replacement for mine ?
 Reply

A  Answered on 7/23/2015 by InyoPools Product Specialist Lennox H.

Hi Howard, The Aqua Rite Display PCB (GLX-PCB-DSP) will be the correct part if you have the AquaRite, SwimPure or AquaTrol Control Panel's. I was not able to cross reference p/n G1-066604G-1 to any specific part.
 Reply


?     Asked on 4/11/2015by Dennis Kloeckener

Is my display # G1-066604F1 compatible with the new main board # GLXPCBRITE, or do I have to order a new display # 2807-11 ( GLX-PCB-DSP ) ?? Also is Turbo Cell T cell 3 compatible with board # GLXPCBRITE ?
 Reply

A  Answered on 4/13/2015 by InyoPools Product Specialist Joe S.

Yes your Display will work with the new board as well as the cell. New board will allow you to choose what cell type you have.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers, Socket Set

Original PCB Circuit board was not working

Written on 9/17/2021 by Guest

Took pictures of original installed circuit board for reference.
Removed original circuit board.
Installed replacement OEM circuit board per INYO Pools installation video.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
3 Rating
5 star:
 
(3)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews