I am replacing a 24" sand filter operating from a Hayward 1HP Super Pump. My pool is an in-ground that holds 35000 gallons. Will the C1200 filter (1.5" pipe) be adequate for this pool which is lightly used?
Reply
Yes this would be a proper fit for your pool. The Hayward Super Pump (1HP) would not be able to exceed the flow capacity of the C1200 allowing it to be a proper and safe fit for your system.
Reply
The filter I had before needed to be backwashed. How do I backwash this Hayward C1200 or C12002?
Reply
This filter model type is a cartridge filter and does not actually need to be "backwashed". The filter cartridge element inside must removed on a regular basis which is on average about every month, rinsed down with a water hose and pressure nozzle of some sort and then put back into place.
Reply
Are there specs on how many microns this filter is rated at? Is there available another filter that won't allow finer particles to pass through?
Reply
As a rule, sand filters sift particles ranging from 20 to 40 microns in size. Cartridge filters can sift particles as small as 10 to 20 microns in size. DE filters can sift contaminants as small as 1 to 3 microns in size. This makes DE filtration at least five to six times more efficient than sand filtration systems.
Reply
Hello, I am considering the C1200 filter for my above ground 24' dia. pool. Will this filter cover the needed GPM and maximum gallons of approximately 22,000 gallons? I have a 1.5 HP pump as well.
Reply
The C1200 filter will handle 120 gpm on a residential pool and will turn over 57,600 gallons in 8 hours. It will be more than plenty for your pool.
Reply
can I just buy a top?
Reply
Hello Sid - The part number for the C1200 lid is CX1200B (4663-06B).
Reply
I have a 11,500 gallon pool. What would be the best filter to get. I am replacing a old sand filter unit and looking to upgrade to a filter based unit.
Reply
I have a 36000 gallon 18 X 36 in ground pool will this filter work with the size of my in ground pool with a 1.5 superpump ?.I'm replacing a old d.e. filter .
Reply
Jamie, Yes. based on the specs of the Hayward C1200 cartridge filter, it can turn over 57,600 gallons in 8 hours (up to 120gpm). Keep in mind that you will not get the same filtration quality that you would with a d.e. filter.
Reply
How do I backwash the Hayward c900 cartridge filter to clear a blockage?
Reply
Karen, To clean the cartridge, you must remove it from the tank and soak it in a cartridge cleaner. Once it has soked for a few hours, you will need to hose it off.
Reply
When my pump comes on, the top section of the filter body raises about 1/4 to 1/2 an inch. Then after running for a while, the "O" ring pops out, causing a massive leak. I replaced the "O" ring but to no avail. I have a model C1200 Hayward filter. Any suggestions on how to fix this?
Reply
Hi Ed, it sounds like the top section of the filter body is not screwed down far enough. Make sure that the cartridge is the correct size and that it is seated all the way down when you place it in the tank. Clear out any debris that may be in the bottom fo the tank. Make sure the groove where the two section of the tank connect is clear. If your O-ring is stretched from popping out, you may have to replace it.
Reply
Does the C1200 come with the cartridge and hoses?
Reply
Hi Trisha - This filter is generally used with an in-ground pool system and is installed with pvc piping. Therefore, it does not come with hoses. It does include a cartridge however.
Reply
This is a follow up question; is it ok to use with an above ground pool? What is the warranty that comes with the product?
Reply
Yes this filter is okay to use with an above ground pool. It has a 10 year warranty on the filter tank and 1 year on parts.
Reply
Hi.....
Is the C1200 big enough for a 25,000 gallon pool?
Thanks!
Reply
Hi Joe, The real question is "Will the C1200 filter be compatible with my pool pump?". The filter has to be able to handle the GPM water flow that is generated by the pool pump. The GPM rating for the C1200 filter is 120 GPM which will handle most pumps up to 2 HP. Most 25,000 gallon pools have pumps with 1 1/2 to 2 HP. Bottom line, If your pool pump is 2 HP or less, the C1200 filter will be large enough for your pool.
Reply
Wil this filter work with a 3/4 HP pump?
Reply
Yes, the Star Clear Plus 120 Sq Ft. Filter 1.5" Ports C1200 will work fine with a 3/4 HP pump.
Reply
Does this system come with a cartridge installed? Also, does it take a professional pool tech to clean the cartridges?
Thanks!
Stan
Reply
Hi Stan, The Star Clear Plus 120 Sq Ft. Filter does includes the filter cartridge inside. It does not take a pool professional to clean the cartridge you can do it yourself. You can review our How To guides: How To: Clean a Pool Cartridge Filter & How To: Clean A Cartridge Filter w/ a Filter Flosser to see how it's done.
Reply
How do you know when to replace the C1200 filter? Mine is 15 years old.
Reply
The filter body only needs to be replaced if it is cracked or damaged. If you are referring to replacing the cartridge, we have a guide that will help answer that question. The guide is titled " How To Determine When a Filter Cartridge Needs to be Replaced".
Reply
is this filter OK for a 1.5 hp pump motor?
Reply
I would recommend either using a larger square footage filter and or a 1 hp up rated motor. In general the 1.5 hp motors and or pumps would have a bit too much pressure to work with the C1200.
Reply
I am replacing a DE filter with a 3/4 hp pump, which never properly ran my pool vacuum. Would the C1200 coupled with a 1hp motor effectively clean my 20,000 gallon pool and have my pool sweeper / vacuum go all the way up my pool walls?
Reply
I have a 40k gallon pool in a house I just purchased which only has an s200 sand filter with a 1HP super pump (well undersized I've come to find out). I'm looking to buy a c1200 to replace the sand filter but is the 1HP pump good enough or do I need a 2? I've seen that the specs on the pump and it doesn't seem to have the flow rate to properly turn over the pool but wanted to check before buying the c1200. Thanks!
Reply
Craig, For a 40,000 gallon pool, I would recommend at the least 225 sq ft if you are converting to a cartridge filter. A 1HP pump sould be sufficient if the total feet of head is within 50-60 feet.
Reply
how do you measure the port hookup, from the inside or outside? I have a Hayward 1.0 hp pump Do I need a 2 inch or 1 1/2 inch port?
Reply
Hi Don, You will have to measure the actual pvc line to find out what size port you need.
Reply
I'm a bit confused. On 12/9/15 Lance asked a question about a 1.5 hp pump and Hector F. answered that this would have to much pressure for the C1200. On 7/7/15 Joe asked about the C1200 and Dennis R. answered that pumps up to 2hp would be fine. So... what's the correct answer? We have an 18x36 with a 10' deep end and have a 1.5 hp pump and a 1hp back up pump (from a prior pool). What would be the best size filter for us?
Reply
Hi Jim, we would always suggest going bigger on your filter. A 2 HP pump on a C1200 would be on the very upper limits of what the C1200 filter could handle, so I would suggest the Hayward C17502 175 Sq. Ft. Filter as you will see longer life out of your pump motor and you will have longer time between cleaning the cartridge.
Reply
I have a 28,000 gallon in ground pool. I just bought the the star clear 12002 with 2" ports hooked up to a new Hayward Tristar variable speed pump. I am finding a lot of conflicting information on what the appropriate cartridge sq.ft. size for my pool. Some articles suggest a cartridge filter size no less than 20% of the number of gallons. Will this filter be undersized for my pool?
Reply
The cartridge filter you purchased will accommodate a pool up to 57,600 gallons. I am sure you will have plenty of proper filtration.
Reply
I have a Hayward C-1200 Star Clear Plus Filter. How do I determine the port size? I am in the process of replacing the filter because the Tie Rod comes out when removing the filter top or cover. I have this filter in operation for 12 years.
Reply
You would need to measure your pipe size to determine the correct 1.5" or 2.0" port size needed. In general, the 1.5" size is the most common for these filters.
Reply
I have a Hayward Star Clear plus CX1200 with a pleatco filter. It's been running fine. Well I notice I didn't have a basket in the pool to collect debris(leaves and what not) ano I bought one and put it in. Well I think the motor blew and since everything is 21 years old, I can't read any info on the motor except GE commercial motors by regal weldit. The by part is iffy. My question is what do I replace it with without replacing the star clear housing and filter?
Reply
Hi Pablo, If you can send us photos of the pump and the p/n that is on the impeller we can find out what size motor or pump you will need.
Reply
Hi, I have an 11,000 gallon in ground pool. Currently I am using a Pentair Intelliflo 3 HP variable speed pump and an old Standard-Rite filter (sand converted to Cartridge at some point). I want to upgrade my filter however since the cartridges for the filter are incredibly expensive. Any suggestions on a new filter?
Reply
What is the model of your current filter? I will need to know that or the distance from your pump to the skimmers so I can calculate your estimated flow rate so I can recommend the correct size of filter.
Reply
I have an 11000 gal pool that currently has a C-900 Hayward filter and a 1-hp single speed pump. I need to replace both the pump and filter. Am thinking of upgrading to the C-1200 filter and a 1.5 hp pump. I have 1.5" pipes and it is about 30' from skimmer to the pump. Should I stick with the C-900 and 1 hp pump or upsize to the 1.5 and C-1200?
Reply
Changing to a 1.5HP would be work for your system as long as you upgrade to the C1200.
Reply
I currently have a C1100, old and leaking at the seal. It appears it is less expensive and better to replace it with a C1200. My pool is 33k gal. Is this a proper replacement. Thanks for your time and advice...Ray
Reply
I currently have a System 3 Filtration system DE Filter. Filtration area is 37sq.ft and filtration rate is 2 GPM/SQ. FT (81.5LPM/SQ.M) Max flow rate 74 GPM. I want to replace it with a Hayward cartridge filter. I was looking at the C1200. Is this too much filter for my pool. This DE filter is the filter that the pool manufacturer installed almost 20 years ago.
Reply
Hello, you would be fine going with this filter. When it comes to sizing a filter for a pool, you can typically never go too large. The reason for this is because if a filter is oversized, the water will be able to flow through at a slower rate and filter better.
Reply
I have a Jandy DEV48 filter,and want to change to a cartridge filter since replacing grids due to DE powder getting in pool.
Would a Hayward C1200 cartridge filter system work? I have a 10K gallon pool and 1.5 hp pump motor.
Reply
I currently have Hayward pump SP2300VSP for my Pool/Spa that has an approx volume of 10,500. I was told that my Hayward Cartridge filter C1200 is to small. I am questioning this information. Do I need a larger filter?
Reply
You may not necessarily need to upgrade the filter but the advantage that you have is that you can dial down the rpm's on the pump decreasing that water pressure in the filter. If that pressure gauge is reading high(average 5-15 on a standard system) then you may want to consider upgrading that filter 50-75 sq ft.
Reply
I have a Hayward Star-Clear II cartridge filter C1100. It is old and in need of replacement. I have a 20 x 40 pool (approx. 33,000 gal). The pump is a Hayward Super II pump using a motor CT1072 motor and a 3/4 HP impeller. What would be the best replacement Hayward star clear plus cartridge filter to buy to work with my pool and pump? The lines are 1 1/2"
Reply
I have a C1200 filter housing, the lip on the lid has developed several cracks and has started to leak. time to replace the lid. can I use a taller lid to give me for filtration, with a bigger filter of course? what parts would I need to do this? thanks
Reply
Technically yes you could but would also need to replace the rod part number 4663-11D, the lid as you knew and would also need to make sure that the base has 2-inch ports because by increasing the flow(if that is what you plan) you may need a 2-inch port.
Reply
Does the Hayward C 1200 also comes with a cartridge ??
Reply
Good Afternoon John- The Star Clear Plus 120 Sq Ft. Filter 1.5" Ports - C1200 only includes the housing. The Pureline Cartridge for Hayward C-1200 (PA120)(C-8412) - PL0146 is sold separately.
Reply
Can you recommend a pump that works well with this filter? I have an 11.5k gallon inground pool with about 75ft of 2 inch pipe from skimmer to pump.
Reply
Hi, Scott. Unfortunately, pumps are sized differently. You can review our How to Size a Pool Pump for Your In-Ground Pool guide for the specific info required.
Reply
Hello, is this a good filter to run with the PL1601 pump? Thanks.
Reply
Hi, Al. Yes; however, the pump flow rate does not exceed 120 GPM.
Reply
What filter would you suggest for the PL1601 pump?
Reply
Alan, If you can provide the exact flow rate of the PL1601 operating on your pool, I will be able to tell what filter will work best. Filters are not sized using a specific pump model. You can review our How To Size a Pool Filter guide for more info.
Reply
I have a Hayward Star Clear Plus 340L32. Sn 64935. C1200 that I want to replace with same! Not sure what port size I need.
Reply
I own the star clear plus 2" model. What is the average pressure it will run on
Reply
Because system pressure varies so much between pools due to pump flow rate, filter size, feet of head, and other aspects there is no average PSI level. To find the "normal" pressure of your system, take a PSI reading after installing a new cartridge or a thorough cleaning of an old one.
Reply
is 18 normal
Reply
I just purchaseda hayward c1200 I also purchased in feb a carvin 1.5 hp i'm having a problem lining it up
what hayward pump 1.5hp would line up with c1200 tu
Reply
Hi, Robert. The pump you purchased requires the Interconnect Self Aligning Union Assembly - 42363408R000 you may still need to raise the filter slightly.
Reply
I am replacing a 1.5HP single speed pump with a new variable speed pump. I currently have a 48SqFt DE filter and plan to replace that at the same time. All of the plumbing to/from the filter and pump is currently 1-1/2 inch. The lines to/from the pool are also 1-1/2 inch. Is this the largest filter I can install with the 1-1/2 inch plumbing constraints?
Reply
the star clear plus 120ft will work for your 1.5" ports. if you want to go with a larger size filter that has 2" ports you will have to get an adapter that goes from 1.5 fitting to 2"
Reply
Hi, I have a Hayward C1100 cartridge filter housing. it is now over 25 years old and I need to replace it. it is springing leaks everywhere.
what is the replacement filter housing assy. is it a C1200 ? if so, what is the price on the complete unit.
please let me know.
Reply
I have the C1200 filter and I need a new top. Can I buy just the top?
Reply
Yes you can purchase just the top please click this link to view or purchase the Hayward C1200 Filter Lid
Reply
I have Hayward PowerFlo MATRIX Pool 2-Speed Pump, 115V, 1.5 HP. Is the Hayward Star-Clear Plus Cartridge 120 sq ft Tank 1.5 in Filter or 2 in filter compatible?
Reply
Hi Gemma. there are a few variables to consider when sizing a pool filter. Here is a guide that we put together called "How To Size a Pool Filter" that should assist.
Reply
Will a 1 hp, 60gpm pump run the hayward w3c1200
Reply
Hi Paul, there are a few variables to consider when sizing a pool pump. Here is a guide for sizing a pool pump in an above ground pool and another for sizing one in an inground pool that should assist.
Reply
will this work for my inground pool 16 x 32 23000 gallons
Reply
Hi Michael, there are a few variables that need to be considered when sizing a pool filter. Here is a guide that we put together called "How To Size a Pool Filter" that should help with that.
Reply
i currently have a hayward ec65a .
1.) is the Hayward W3C1200 adequate to replace it
2.) can i use my super pump with it (it is fine)
Reply
Hi Dan, your existing super pump should be fine to use with a number of different filters. There are a few variables that need to be considered when sizing a pool filter. Here is a guide that we put together called "How To Size a Pool Filter" that should help with that. The W3C1200 has 120 square feet of filtration and works well with smaller pools.
Reply
I'm needing a sanity check- replacing an old 36sqft Hayward Pro Grid DE Filter rated for 72gpm. Pump is a 1.5hp Super II, 16,000g pool with estimated 60ft head, so 69gpm. All lines are 1.5, so seems like that would limit me to 60gpm anyway. Wanting to get a cartridge filter, and this Star Clear Plus 120 with 1.5in ports seems more than capable for my system but so much smaller in dimensions to my existing filter that I'm worried I've missed something!
Reply
Hello Will. Utilizing Hayward Cartridge Filter Design Flow Rate information and Super II Pump Performance Data, the Hayward Star Clear Plus 120 sq ft cartridge filter model W3C1200 is a compatible replacement cartridge filter for the Hayward ProGrid 36 sq ft DE Filter model DE3620. The 1.5" pipe size limits the maximum flow rate to 60 GPM according to most resources. The 60GPM flow rate is below both filter Design Flow Rates per Hayward published data. Monitoring filter pressure will indicate the frequency with which the cartridge will necessitate cleaning. You may wish to consider the Hayward Star Clear Plus 175 sq ft cartridge filter model W3C17502, reducing the cartridge cleaning frequency. W3C17502
Reply
