$36.99

Qty:

By PureLine


Details

Top

Part # GOKIT14

Alternate Part #'s 65014, GO KIT 14, PL1014, 90-423-3014, ALDGO-KIT14, APCK1007

Product Description

Standard tune up kit for the Jacuzzi Magnum pump includes the shaft seal and all o-rings, gaskets and lubricant.

We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor.  If you use your old shaft seal, it will not mate up properly with the new motor and may leak.

This Tune Up Kit Works on These Pumps:

  • All Jacuzzi Magnum Pumps 1/2 HP - 3 HP single and dual speed models, including Magnum Plus and Magnum Force.

Tune Up Kit Includes:

  • Motor Shaft Seal
  • Case O-Ring
  • Plug O-Ring
  • Strainer O-Ring After 7/89
  • Diffuser Square O-Ring
  • Lubricant

For More Pool Pump Motors

Top

?     Asked on 11/25/2022by Thor

Will the GOKIT14 work with a Jacuzzi J-300 series 1 1/2 HP two speed pump? Please see attached pictures. Thanks, Thor

 Reply

A  Answered on 11/25/2022 by InyoPools Product Specialist Hector F.

Hello Thor, unfortunately we do not currently carry parts for the Jacuzzi J3000 pump however please click here to be directed to fortywinks.com as they do carry these parts.  
 Reply


?     Asked on 6/17/2020by Inyo Visitor

Will this for carvin pump number 94028942

 Reply

A  Answered on 11/20/2020 by InyoPools Product Specialist Hector F.

Hi Rebecca, for us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
 Reply


?     Asked on 5/27/2020by EDWARD MCMILLEN

I have replaced the spring shaft seal and plastic bearing in my Jacuzzi Magnum. When I tighten the impeller it becomes so tight that the motor won't turn. Am I missing a piece or doing something wrong?
 Reply

A  Answered on 10/21/2020 by InyoPools Product Specialist Hector F.

Hi Edward, these impellers only need to be hand-tightened until their real first resistance. Also if the shaft seal is installed incorrectly it could also cause this. Here is a guide that we put together called "How To Replace a Pool Motor Shaft Seal" that may also assist. 
 Reply


?     Asked on 8/29/2019by Mitchell Stark

I have 29 year old Magnum plus pump and 2 hp magnetek energy saver motor. Soul this be the correct o-ring and seal kit.
 Reply

A  Answered on 8/30/2019 by InyoPools Product Specialist Lennox H.

Hi, Mitchell. This kit is used on models manufactured after 07/89. 
 Reply


?     Asked on 6/23/2019by Inyo Visitor

I HAVE A 1081 PUMP THAT LEAKS IS THERE A REPAIR KIT AVAIBLE AND WHAT IS THE COST
 Reply

A  Answered on 6/23/2019 by InyoPools Product Specialist Hector F.

We may carry the seal kit for your pump but we would need the model name or number of the front pump housing that the motor bolts to. If you cannot locate that model you can always email us a few images of the pump to upload@inyopools.com so we can confirm for you. 
 Reply


?     Asked on 5/30/2018by Tom

I just received a new sq."O" ring from you for my Jacuzzi Magnum pump, and every time I slip it on to the pump, it slide off. Is there a trick to keeping it on?
 Reply

A  Answered on 5/30/2018 by InyoPools Product Specialist Hector F.

Sometimes using extra O ring lubricant in small globs of it in random spots on the o ring to the pump housing helps to keep it in place. 
 Reply


?     Asked on 6/23/2017by camille

My pool pump Jaccuzi Magnum 1500 is running but not pumping water
 Reply

A  Answered on 6/24/2017 by InyoPools Product Specialist Lennox H.

Hi, Camille. A few things can cause a pump to run but not circulate water. A clogged impeller, unable to prime, and a bad motor if it sounds like it's running but the shaft isn't spinning. I would recommend taking the pump apart and inspected it. You can also get useful info in our 8 Answers to “Why Is My Pool Pump Not Working?” Blog.
 Reply


?     Asked on 4/23/2017by Robert

Can you provide the thickness dimension on the motor to pump o-ring? I bought a replacement that is 3/16" thick but can't get it to install even with lots of lube, letting the gasket sit in the sun, etc. Can't figure out the issue.
 Reply

A  Answered on 4/23/2017 by InyoPools Product Specialist Scott W.

Yes, the pump housing o-ring has a thickness of 3/16".
 Reply


?     Asked on 9/24/2016by I.V.

what side of the shaft seal should be facing up/out one install "white" ceramic or "black" rubber? Where or how do you install the Case O-ring?
 Reply

A  Answered on 9/25/2016 by InyoPools Product Specialist Stacey M.

Hello, the black rubber should be facing up, the other end is should be siliconed in the seal plate. Please watch our "how to" on how to change shaft seal. http://www.inyopools.com/HowToPage/how_to_change_the_shaft_seal_on_a_hayward_matrix_pump.aspx
 Reply


?     Asked on 6/27/2016by Inyo Visitor

I seem to be leaking water between the motor and pump. Will this tune up kit fix the problem?
 Reply

A  Answered on 6/28/2016 by InyoPools Product Specialist Alan M.

That's where I would start at if there isn't anywhere on your pump housing that's leaking water or cracked. If you haven't changed the seals for a while they that would be a great place to start.
 Reply


?     Asked on 6/2/2016by Mark

I have a leak between what I would call the motor and the skimmer basket. It is not the outer plastic ring. I was wondering if this was what I should use to try to fix the leak? Also, how hard should it be to pull the 2 pieces apart?
 Reply

A  Answered on 6/3/2016 by InyoPools Product Specialist Scott W.

That's where I would start at if there isn't anywhere on your pump housing that's leaking water or cracked. If you haven't changed the seals for a while they that would be a great place to start.
 Reply


?     Asked on 8/13/2015by fallmd

Strainer or box of jacuzzi magnum plus has a slight crack,and water spurts out.What glue can be used to plug it?
 Reply

A  Answered on 8/13/2015 by InyoPools Product Specialist Robert M.

We do not recommend trying to repair the crack with any type of glue. We recommend replacing the entire housing. Part number 42234506K (5064-052) is the correct replacement housing.
 Reply


?     Asked on 5/16/2015by Inyo Visitor

Will this work for a 1.5 hp magnum force with an AO smith motor?
 Reply

A  Answered on 5/16/2015 by InyoPools Product Specialist Patrick P.

Yes this would be the correct tune up kit for a Jacuzzi Magnum Force with AO Smith Motor.
 Reply


?     Asked on 10/15/2014by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
 Reply

A  Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
 Reply


?     Asked on 2/13/2012by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
 Reply

A  Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
 Reply


Top
Difficulty

Est. Repair Time

4 to 8 hrs

Tools Needed

Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set, Adjustable Wrench

My Carvin Magnaforce pool pump motor (14 yr old) shorted out - required replaceement

Written on 8/4/2021 by Guest

Ordered new replacement motor and the pump seal kit. Using the kit supplied seals and gaskets I replaced all parts during the pump motor replacement. This ensured that upon completion I experienced no leaks or problems. The pump has been running for two weeks without incident or leaks.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

More than 8 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench

Replace pool pump motor and install new gaskets

Written on 8/31/2019 by Rob T.

Replaced pool pump motor and installed new gaskets. The gaskets came in a kit that must be applicable to several different motors and pumps. No instructions to assist in identifying where to place these gaskets nor which gaskets applied to a Magnum Force pump. Some gaskets intended for the diffuser assembly and at least one appeared to require being placed inside the pool pump housing. Very confusing.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.62  out of 5 stars)
26 Rating
5 star:
 
(19)
4 star:
 
(6)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(1)

The Most Helpful Review


The Most Recent Reviews