Part # 37220211D
Dimensions 17.5" L x 8" W x 8.5" D
Alternate Part #'s PF-50-2N22C, PF-50-2N22F, PF502N22F, 34-270-3598, WW37220211D, WWP-10-1423
When matching pumps always use AMPERAGE rather than Horsepower. Many times the labeled Horsepower does not accurately represent actual horsepower.
The Executive 56 Frame Spa Pump has an executive wet end designed for 56-Frame motors along with two double-shielded ball bearings with moisture-resistant grease for quieter operation and long life. The dual speed motors have insulated windings for increased efficiency and large, highly versatile 6-1/2" diameter wet end for higher head pressure. A split capacitor (start and run) allows for less energy consumption.
Spa Pump Features:
Manufacturer | Waterway |
Pump Model | Executive |
Speed | 2 Speed (2-Spd) |
Motor Voltage | 230v |
Drain Plug Location | 3,6,9 o`clock |
Suction Style | Center |
Suction Connection Type | Male Buttress Thread (mbt) |
Suction Pipe Size | 2" |
Discharge Style | Side |
Discharge Connection Type | Male Buttress Thread (mbt) |
Discharge Pipe Size | 2" |
Horsepower | 5.0hp |
Motor Frame | 56 Frame Thru-Bolt |
Motor Amperage/Wattage | 16.4A/4.8A |
All 3 of my pumps in our CalSpa are dead and need to be replaced. Here are some pics. Recommendations for replacements? Can I go lower HP and Amps to get cheaper motors or do I need to stay about the same?
Hi Steve, We suggest quantity 3 of the following pumps as replacements 34-402-5254 Replacement Cal Spa Pumps we do not suggest going down on the HP as these pumps are sized specifically to your jet and filter requirements. By the way, we do currently have these pumps in stock ready to ship!
Reply
I need to find the replacement pump for the whole unit. Its about 15 years old.
Thank you!
The replacement for your spa pump is AquaFlo model 061205002040.
Reply
Hello I need to find the comparable pomp for my jacuzzi pomp is leaking here some picture.Please let me know which pomp should I order
Thank you
I believe this is the replacement pump that I need. Will it come with new seals as well?
Hello Eric, Yes that pump Waterway Executive 56 Spa Pump - 5 HP does come with the seals as it is a whole pump and motor replacement.
Reply
i need the 2 hose adapters where the drain plugs are at 9 and 6 o`clock i cannot find part #`s for these i did not know they were not included
Reply
My motor is leaking around the shaft between wet and dry, what are my options for that problem? The model number is C55MWKBT-4824
Reply
Most often these leaks are caused by failed seals and gaskets but in order to confirm which ones you will need, you will need to know the specific pump make and model.
Reply
I need a replacement for a Cal Spa hot tub (GE Motor Model 5KCR49WN2370AX).
Reply
Hi James, Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Can the wet end be rotated 90 degrees, this one points straight up and my connection is on the side 1/4 turn to hit my existing spa connection
Reply
Hi Dave, Yes this can be rotated so the discharge port is at 90 degrees.
Reply
I am trying to match up my old pump, it is an Executive 56 5HP 230V 12.0/4.4amps, Part # PF-40-2N22C
Reply
Hi Dave, You will actually need this 3721621-1D Waterway Spa Pump we have this pump in stock ready to ship!
Reply
Good Morning Mark...…. I am looking for the front portion of the wet end. #s 311-1239-DNB and 311-1200. I've located it, but mine has two nipples in the front for hoses. What I have found only has plugs in those location. The plugs also seem to be non removable. Will you please give me your educated advice. Thank You .
Reply
You can remove the plugs and insert the adapters for the two nipples.
Reply
Due to mfg design changes we actually recommend that you change the complete wet end & not just the faceplate. The original faceplate used 1 o-ring & the newer style uses 2 o-rings on the faceplate. We have spoken with customers that have had issues making the newer style work with the older style volute. Just an FYI. The bleed plugs are removable & the part #'s for the barb replacement plugs are 9404-01 & o-ring # 4600-4661
Reply
Mark : The spa pump has 6HP tag on it, and the following numbers in the plastic casting 311-1239-DNB - 311-1200. The motor part # is 3721621- OD76.Waterway Model PF-30-2N22M. Which one would be the right pump, motor combination to replace it with?
Thanks: Ray
Reply
Hi, Ray. Most spa pumps are specially labeled. Based on the info provided the Waterway Executive Pump 4 HP 230V 2-SD - 3721621-1D is the replacement.
Reply
What kind if connector is on the plug? My pump has 3 round pins in a diagonal (/) pattern and 1 flat pin that plugs into a LA Spas control center.
Reply
Hello John - The pump does not come with a cord. You can take the cord off of your old pump and attach it to the new pump.
Reply