By Zodiac



Part # 6203-022A

Manufacturer Code R0013200

Dimensions 3.35" L x 2.4" W x 1.95" D

Alternate Part #'s 3902, 4037P-EA, 604393, 6203-022, 6203-022A, 6203-254, E75198, R0013200, R0097700, 47-295-1027, JDYR0013200, JNDR0013200, LAR-151-2613

Product Description

Pressure Switch 2 PSI - R0013200


?     Asked on 5/24/2015by Vince

the display does not show any flow of water and the display does not show anything but there is water going thru the heater could this be the problem

A  Answered on 5/24/2015 by InyoPools Product Specialist Patrick P.

Hi Vince it is possible that this could be the issue as this is one of the most common parts in pool heaters to go bad. It may also be the case that your flow through the heater is lower than 2 PSI as this is the pressure required to activate the switch.

?     Asked on 6/24/2015by Peter

The code FL4 comes on and will go away after turning pump on and off or by just letting the heater cycle 2 or 3 times. Heater will go into display mode and display FL4 if after 3 times it does not cycle on. I can repeat steps above and it may come on line, it may not. Could this be the pressure/flow switch. Thank you Peter

A  Answered on 6/25/2015 by InyoPools Product Specialist Lennox H.

Hi Peter, The "FL4" error code in the Lite 2 LJ Troubleshooting Guide refers to a bad Igniter (R0367100).

?     Asked on 8/29/2016by Charles

I need to replace our pressure switch,on our LD250N. how do I select the correct one,with the correct PSI setting?

A  Answered on 8/30/2016 by InyoPools Product Specialist Alan M.

There should be a model number on a sticker on the pressure switch that you are looking to replace. I would verify this information against the alternate part numbers listed for that switch for confirmation.

?     Asked on 12/22/2016by Inyo Visitor

what is a fl5 error code

A  Answered on 12/22/2016 by InyoPools Product Specialist Adam Y.

Good afternoon bcoutant1@comcast.net, If this is for a Jandy Heater. It is because the voltage is wrong. You can call Jandy at 1-800-822-7933 and they will be happy to assist you with this.

?     Asked on 5/14/2017by David

I have a jandy lite 2 lj125n i am getting a fl o display i am thinking it is the presure switch just not sure witch one r0013200 or roo11300 or r0015500 there are no numbers on the switch. I have power at the whit eire but nothing at the black, I also have good pressue from the pump thru the heater to the pool but no indication that the water is moving basred on the display pannel ant the control pannel has its light on. any help would be great. thanks David

A  Answered on 5/16/2017 by InyoPools Product Specialist Lennox H.

Hi, David. The Pressure Switch 2PSI - R0013200 is the item that you'll need.


Est. Repair Time

Less than 1 hr

Tools Needed

Box end wrench and a adjustable wrench.

Pressure switch over heated

Written on 7/9/2017 by Skip.

While cleaning the basket to my pump I forgot to shut off the heater and the pressure switch got over heated. So I sent an email to Hector who confirmed that Inyo Pools had the part. When I received it I took the old one off and installed the new one. Then I turned on the heater and confirmed that it worked just like the old one.

Were these instructions helpful? 


Review Summary

 (Average 4  out of 5 stars)
1 Ratings
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Recent Reviews