Part # 4040-04
Manufacturer Code SPX1082K
Dimensions 7.75" X 5.38"
Alternate Part #'s 2511917, 59200233, 936, HAY2511917, SP1082K, SP1082K4, SPX1082K, 51-150-1524, HAY-251-1917, HAYSPX1082K
This is a replacement weir for Hayward pool skimmer models SP1082, SP1083, SP1084, SP1085, SP1075, SP1075T, SP1076, SP1077. It is also used on the larger Skim Filter SF-400 model (be sure to measure existing weir).
The numbers on the weir door are 51-6222. It is a Pentair but the skimmer lid reads Paddock, the name of the pool builder.There is no model number but says the flow rating is 10-55 GPM
Hello, The part number you will need based on the part number 51-6222 ishttp://www.inyopools.com/Products/07501352028751.htm?Keywords=51-6222
I need to replace my weir door, pretty sure it is Hayward but unknown part number. Opening approximately 7 1/2" width and height 6". There are 2 bolts approximately 5" apart. Attached photos - any suggestions? Thank-you!
Hi Richard, Could see if you can pull any part numbers off of the skimmer lid or skimmer basket? The part numbers should be embossed into the plastic you can simply reply back to this email with that information.
This persons description and picture match mine. Mine is a Hayward SP 1070 B. 7 1/2” long by 6” tall. What will fit it? The compression weirs I’ve tried, all cone off when the kids get the water rocking.
I need to replace just the sponge on the door? Do you sale just that? I f so what is the part number?
Hi. Unfortunately, the foam is not available as a separate part for this weir. You will have to purchase the complete Weir.
we have a really old haywood skimmer must be at least 30 years old unfortunately door flap just broken we have made a temporary repair but hoping the SPX 10821K spare part will fit.
Our door flap had the number 80 171 (probably too old to find registered anywhere!) on the back and measured 7 3/4 ins wide x 5 3/4 tall..more concerned whether the lugs would fit?.....Pool always been well maintained but we are looking for a quick replacement part repair .
Hello. I have to replace the weir (door) on my skimmer. It's a Hayward SP1082K4 in white. Do you carry this item?
Hi, Robert. This Skimmer Weir - SPX1082K is the current replacement.
I need a new skimmer "Trap door" Hayward part number SP 1082K in white. Do you have such a part? One of the tabs on the door broke off.
This will be the correct weir door for your model.
Hello, I have two Hayward Weirs and both are warped, is there a better replacement for them other than just the factory ones?
Hi, I wondered if you carry just the piece of hard foam that fits into Hayward skimmer part sp1082k4. I don't need to replace the whole piece, just the foam. Thanks!
Hi Julie, I'm sorry we do not carry just the foam, only the foam and the weir.
My pool is missing the weir therefor I can't measure it. Is there another way to find out what model number skimmer I have? I'm pretty sure it's a Hayward because there is an "H" under the cover.
Hi, typically on the underside of the skimmer lid there is a model number that identifies the entire skimmer. From there we can locate the correct weir gate part. The "H" would denote you have a Hayward skimmer.
(4 out of 5 stars) Weir that works
Reviewed By: Dave J. from Spokane, WA ()
Pros: ease of install
Cons: none so far
This is not exactly like my original weir, which had rod all the way through and was somewhat difficult to get out. This one has more like a button on each side that you squeeze and it pops right in and fit perfectly.
(5 out of 5 stars) Brand New Skimmer Weir
Reviewed By: Darlene N. from Baltimore, MD ()
Our old skimmer weirs were stained, discolored and just generally ugly. While ordering some filter parts, I found it easy to order new skimmer weirs at the same time. Simple to order and simple to install!