Model # W3RC9740CUB
Manufacturer Code RC9740CUB
Alternate Part #'s RC9740CUB, HAYW3RC9740CUB
SharkVac SeriesProduct Description
Both SharkVac and SharkVac XL™ by Hayward® are built with the highest-quality components and proven technology that create reliable, consistent results while maximizing energy efficiency. Whether you clean your pool floor and coves with SharkVac or cover the floor, walls, coves and waterline with SharkVac XL, the cleaners’ robust, low-profile design and top-access filters give them an added bite.
Efficient cleaning program
|Model||Cleaner Type||Pool Coverage||Cleaning Cycle||Pool Size||Pool Surface|
|RC9740CUB||Robotic||Pool floor, coves||2 hours||up to 20' x 40'||Gunite, Vinyl, Fiberglass, Pebble and Tile|
My Sharkvac will not advance forward or backward. It is however moving water through the system which is visible by the turbulent water I see coming to the surface. I’ve checked to make sure the drive wheel isn’t broken or out of socket and nothing seems to be binding the one track that I see. Help...?!
Thanks for any tips...
I pulled this from the Hayward website...No movement but the impeller turns • Check with the scanner for communication failure, see scanner section to diagnose. • Check for impeller obstruction. • Check for broken blades. • Check the electrical source for a proper voltage range of 115-125v, including an extension cord if used. ¾No movement and no pump discharge • Drive motor pin or drive motor is broken possibly due to overload during use. To avoid repeat failure, follow-up with the customer for obstructions in the pool such as a ladder. The Scanner will display a Drive Over Current signal if the machine has been caught on an obstruction. • Check for belt or roller obstruction • Check for broken impeller • Check for missing roller tube bearing screws, 2 per sideHere is a link to more Troubleshooting for the TigerShark
Does the SharkVac clean the walls and stairs of the pool? Also, does it remove the algae and bacteria? Thank you.
This cleaner does not clean the walls or stairs. This cleaner is a floor specific cleaner. It will vacuum algae from the walls of the pool. Keep in mind that algae is a plant that is growing in your pool and needs to be chemically treated. This cleaner will not remove bacteria. With proper sanitisation levels in your pool, bacteria will be eliminated.
Can the Hayward SharkVac be used in a vinyl liner pool?
Leslies, this information is taken straight from the Hayward Site for the Sharkvac : In-ground residential pools up to 20' x 40'All surfaces - vinyl, concrete, fiberglass, tile pools SharkVac cleans pool floor only. SharkVac XL cleans pool floor coves, walls and waterline.
here is my problem. the dirth goes out by the top of the motor. i clean the filter and the bucket.can you tell me what's wrong with it . i have a e.vac sharkvac robotic pool cleaner. thank's
Pierre, You may need to replace the Filter Cartridge (70101) and or the Filter Door if the debris is bypass the unit and getting back into the pool. The filters are probably old that there no longer able to capture the debris so is letting it back into the pool.
(5 out of 5 stars) Excellent Pool Cleaner
Reviewed By: Amy W. from Corpus Christi,Tx, ()
Pros: Easy to use. Just drop it in the pool
Cons: Rinsing out the filters.
We have been using the shark everyday and are amazed at all of the dirt and leaves it picks up. It even picks up the lawn cuttings that blow in the pool. The best part is that you don't have to spend hrs. cleaning, it does it for you.
(3 out of 5 stars) fair pool cleaner
Reviewed By: cleaner from Wood Ridge, NJ ()
Pros: Saves labor
Cons: Not 100% civerage
I expected it to do a better job. I used it 2 times, and each time it failed to cover the entire pool bottom. One complete section in the deep end was missed and it had to be cleaned by hand. Perhaps there is a place where I could put it down that it would cover all. It says that it takes 10 minutes to configure the pool but it got started immediately after turning on.