Is the salt included with the salt chlorine generator?
Reply
No, salt is not included. You would purchase the salt locally and the quantity will depend upon the number of gallons of water in your pool. Use a salt that is at least 99.8% pure NaCl. The preferred salt is evaporated, granulated, food quality, and NON-iodized. Avoid using salt with anti-caking agents like sodium ferrocyanide, also known as yellow YPS (prussiate of soda). These cause some discoloration of fittings and pool surface finishes. DO NOT use calcium chloride.
Reply
I am replacing a clormatic III cmc 700 (Jandy) Chlorinater that is 12' in total length. I don't have any additional room - what is the length of the purlink 7-blade cell kit?
Reply
Jim - The total length of the PLC700 with unions is 16-5/8". According to the PLC700 Owner's manual the the pipe cutout required is 13-7/8".
Reply
I just need the cord that plugs into the chlorinator. Is it possible to get just this part?
Reply
Hello, Thank you for your question. We do carry the cords for the AquaPure system. Please review our Jandy AquaPure Models 700 & 1400 parts page.
Reply
Can a novice change out the old cell and put in the new one?
Reply
Hello Garvin, the cell is easy to install. Here is a link to the Jandy Aquapure Salt Water Chlorinator manual. On pages 13-14 they cover the installation of the cell.
Reply
My Jandy salt cell #R478900 needs replacement, which part do I need? My pool is 11,000 gals.
Reply
Hi Kurt, Could you take a photo of your salt cell as well as your power supply and send to us? To send the photos simply reply to this email or send to upload@inyopools.com this will help us determine the proper replacement salt cell for you.
Reply
i need a plc 700 generator my cell is out .i see that this has 2 prongs i think mine has 3? does it make a difference?can i use this and does all the wires in the pictures come with it thanks.
Reply
Hi, Brian. This PLC700 Cell Kit has 2 prongs and does come with the Power Cord, Tri Sensor and Cell.
Reply
on the generic jandy cell ,do the ends all screw on as if the 700 cell?and is the wiring the same as the 700?i just replaced my cell and wiring when i saw this .if i need it again i would go for this if it setsup..thanks
Reply
Hi, RB. This cell is a drop-in replacement for the OEM cell. The unions and wiring of the OEM cell will be the same
Reply
I have a 16,000 gallon pool and my aquapure seems to have gone bad, model R0452400. Does the PLC700 work as a replacement or the PLC1400? I have cleaned it and still error it out and producing zero chlorine. I am concerned as well as my swg has three connectors and these replacements on,y have two, is that an issue?
Is the generic pureline jandy replacement is as good as the name branded jandy
Reply
I have a indicator module attached to the cell sensor. I've seen a lot of replacement kits without the indicator module. Can I just tied the old module to the new sensor?
Reply
Hi, Gail. Unfortunately, you cannot.
Reply
My pool is a 12,000 Gal regular chlorinated pool, that simply is controlled by dial timer for a Pentair InterFlow pump, and I want to convert it into a saltwater pool.
Will this Jandy salt chlorinator hook up and work with my pump, or is equipped with a flow sensor that regulates the production of chlorine based on the detected flow?
Reply
This is only a replacement cell and not a complete salt system. We do not carry the Jandy complete salt system but please consider the Pureline Crystal Pure models or maybe even the Pentair Intellichlor models.
Reply
my aqua pure system wouldn't produce chlorine so . i notice the cell on and cell cleaning lights on at the same time. replaced the cell and same thing
Reply
Thank you for contacting Inyo pools, If you got the kit that comes with the censor you may have to change the firmware settings. Here is there Fluidra Jandy support number 1-800-822-7933
Reply
