I have a twist lock plug on my filter. I am assuming that you can plug in this type of plug into the timer? Also my filter is a 1.5 HP and the specs say it is good for 1 HP. Can I use this or is there another model that will work?
Reply
This timer is designed specifically for pumps with a twist cord, however it can only handle pumps up to 1.0 HP. We do not have a timer available for twist lock pumps over 1.0 HP.
Reply
I have a 1 1/2 HP Hayward filter, I need a timer box that I can connect to it. Will this handle it or do you have another timer that might?
Reply
This will only accommodate up to 1.0 HP pump. If this is for an above ground pool pump then you could use the following timer SP1500FT http://www.inyopools.com/Products/02200022032590.htm
Reply
Is the the plug or the receptacle twist lock?
Reply
The recptacle on the timer is designed to accept a twist lock plug and the plug coming off of the timer is also twist lock. So both the receptacle and plug are twist lock.
Reply
Can this timer be mounted to a wooden receptacle post?
Reply
According to Intermatic, the P1131has a keyhole on the back which will allow it to be mounted to a post with a screw or nail. They recommend mounting the timer at least 1 foot above any standing water or snow.
Reply
Clock is keeping time but not turning on pump or turning off.trippers are in the time that I set and there is power. Just started malfunctioning a week or two ago. The timer is approximately three years old. Any ideas. Thanks.
Reply
Hi Bob. I had the same problem with a similar model timer. I fixed it by replacing the small motor inside, which was pretty simple. If you power down and take a look at the inside you may find a part number for that motor. Otherwise you can give Intermatic a call at 815-675-7000 and check for a better solution.
Reply
where can I get replacement green/red trippers?
Reply
Hi Paul, The Plastic Tripper (156PB10398A) are the trippers for this timer, which we do have available.
Reply
Do you have a timer for above ground pool with Hayward 1.5 pump? If not, know where I can get?
Reply
Hi Sandra, This timer can be used with a 1.5 hp pump as long as the pump does not draw more than 20 amps at 115 volts.
Reply
Wil this time work on a Hayward Power-Flo Matrix Pump, SP1510Z1 XEHC (Part O-196035-01) - 115 V, 12 Amps, 1.0 HP? Trying to find a timer that works with the multi-prong plug of the pump.
Thank for you help.
Reply
Hi, George. This timer will power your 1HP Hayward Power-Flo Matrix Pump with a twist lock power cord.
Reply
Looking for AG pool timer that will accept 4-prong twist plug from pool pump (1 Hp, 115 v, 12 amp). Do you have anything that works or know where to get one?
Reply
Hi, John. We do not have a timer that will accept a 4-prong twist lock power cord.
Reply
Hi, I have an above ground pump with this twist lock plug, the pump has a 1/2 hp or 2 hp option. I only ever use the 1/2 hp, option and run the pump 24 hours. I’m looking to run the pump less and want this timer, however, will the 2hp setting bother the timer if I don’t run the pump on that setting? Thanks for your input!
Reply
Hi, Robin. This timer will not be able to power the high-speed function of the motor. You can use this timer to operate the pump on the low speed. function. The pump must have a toggle with and operate at 115 volts in order to use this timer.
Reply
Hi.
Do you ship to Canada
Thanx Cliff
Reply
Yes, we do ship to Canada. Please email your items needed and postal code to upload@inyopools.com so we can get you an estimate.
Reply
says up to 1hp..what about 1.5HP..will that trip the breaker?
Reply
Hello Jon. The Intermatic Above Ground Pool Timer Twist Lock Plug and Receptacle is compatible with a 1.5 HP motor (pump) providing the amperage draw does not exceed 20 Amps at 120 VAC. Attached please find product information posted on the Intermatic Website for the P1131 Timer Outdoor Mechanical Plug-In Timer with Built-In Enclosure Intermatic guidelines 1.0 HP, 16 FLA, 96 LRA @ 120 VAC references Three Phase Motors.
Reply
