Part # T101P3
Alternate Part #'s _T101P3, INTT101P3, ITMT101P3
This heavy duty mechanical time switch is designed for industrial, commercial and residential applications. This time switch has the highest horsepower ratings in the industry for loads up to 40 amps resistive from 120 to 480 volts providing direct 24 hour time switch control of most loads.
This series provides 1 to 12 "ON/OFF" operations each day with minimum ON/OFF times of 1 hour. All models are equipped with one "ON" and one "OFF" tripper.
Accessories:
Click here for more Intermatic Timers
My pool pump motor indicates V115/230. Will thistimer accommodate the pool pump? Also,can you tell me the voltage on the clock motor?
Reply
Your pump can be wired either 115V or 230V If you have your pool pump wired at 230V than you would want to go with the T104P3 timer if you have the pump wired at 115V than you would want to go with the T101P3 timer. T104P3 timer has a 230V time clock motor and the T101P3 timer has a 115V time clock motor. You may purchase either of these time clocks through the following link http://www.inyopools.com/controls_intermatic.aspx
Reply
How many on/off devices come with the unit? I am using this for my eletric hot water heater, I want the heater to come on around 5:00AM and off at 7:00AM, then on again at 5:00PM and off and 7:00PM. So I guess I'm asking can I program two on and off's or do I have to buy something else?
Reply
This timer comes with one "On" tripper and one "Off" tripper but can accommodate up to 12 On/Off positions. So to accomplish the following "...come on around 5:00AM and off at 7:00AM, then on again at 5:00PM and off and 7:00PM" You would require the purchase of the timer which comes with 2 trippers, plus the purchase of one additional set of on / off trippers which you may view or purchase here http://www.inyopools.com/Products/02400004003526.htm
Reply
Does this timer have knockouts for the electrical and where are they located?
Reply
Here is all the information we have regarding the knockouts: Knockouts - Combination 1/2" - 3/4" nominal knockouts, one on the back and each side of case, two on bottom
Reply
My pool pump is a 1.39 HP and as a Hubbell hb5666c plug. What kind of timer do I need to have it run turn and off every four hours.
Thank you
Reply
Hi Marvin, If your pump is wired 115V then this would be the timer for you. If your pump is wired 240V then you would require the Intermatic 240V Pool Pump Timer T104P3
Reply
Less than 1 hr
Screwdriver
4 1
I REMOVED THE OLD TIMER, USING A FLATHEAD SCREWDRIVER AFTER MAKING SURE THAT POWER TO THE DEVICE WAS TURNED OFF BY DISCONNECTING THE CIRCUIT BREAKER, AND THE MAIN POWER SWITCH. I THEN TOOK A PICTURE OF THE OLD DEVICE AND THE WIRE CONNECTIONS, DISCONNECTED THE OLD WIRES, AND INSTALLED THE NEW DEVICE USING THE NEW SCREWS PROVIDED. I THEN RE-CONNECTED THE WIRES USING THE PICTURE TO MAKE SURE THE WIRES WERE HOOKED UP CORRECTLY.
The Most Helpful Review
3 2
(5 out of 5 stars) Easy to install timer
Reviewed By: Ted W. from Dover, Ohio ()
Very easy to install. Saves me a lot on my electric bill
Was this review helpful to you?
The Most Recent Reviews
2 1
(5 out of 5 stars) timer
Reviewed By: Mike ()
Pros: easy install
Cons: none
I found it to be very easy to install, worked like clock work. If you want to save money on electricty this is the way to go.
Was this review helpful to you?