PER THE MANUFACTURER: THIS ITEM IS NOT AVAILABLE FOR SALE ONLINE
Part # JEP2.0
Manufacturer Code VSSHP270AUT
.png)
Note: The Variable-Speed Pump Controller - JEPR is required in order to operate this pump
Jandy's Variable Speed e-Pump - The e-Pump's 8 variable speeds and high efficiency motor make it the quietest and most efficient pump available - saving on energy cost up 70%. Optional e-Pump controller manages eight speeds, features two independent timers, and can be installed remotely up to 200 feet away.Jandy ePUMP interfaces with the Aqualink RS & PDA systems or as a stand alone system with it's own proprietary controller that includes a two-speed timer and LCD display. Featuring Ultra efficient, ECM, permanent magnet motor and extra long motor life.
Dimensions: Overall Length 34 1/4", Heigth 15 1/4", Width 11 3/8", Width at base 9" 
Note: A separate controller is required in order to operate this pump
I Want to install a variable speed pump and my
Present system includes a 1.5 HP pump and a Jandy RS6 controller. What do I need to purchase to install a variable speed pump that is 100% compatible with my my RS6?
Reply
This depends on the revision of your software, do you know the revision letter of your Aqualink software or roughly how old the software is? If your Aqualink is older then 4 years then you would need to get this conversion kit here http://www.inyopools.com/controls_jandy_control.aspx (bottom of page) Part # 7092 which includes the new software and a new upgraded indoor control remote. There is also a stand alone remote control here which will work http://www.inyopools.com/Products/02600018047487.htm
Reply
I currently have a pentair challenger single speed 1HP motor. 2" pipes, 12.5k gallon pool with 48sf filter (about 15ft from pool and 45ft from farthest skimmer). Is it possible to use a 2HP pump on my system as long as I used the lower 4 speeds or could it cause a problem? Thank you.
Reply
Yes this should work just fine operating within gpm ratings. I recommend to make sure that you use a 2 hp uprate model pump.
Reply
Will this model communicate with the Jandy motherboard I have and the Jandy controls I have inside the house?
Reply
It's going to depend on which automation system you have. That pump only works with Aqualink RS/OneTouch, ePump controller and Aqualink RS PDA
Reply
That pump only works with Aqualink RS/OneTouch, ePump controller and Aqualink RS PDA
How do I read the automation system on my current installation?
Reply
If you don't have any indications on your current unit then you can attach a picture of it so I can identify it.
Reply
The Most Helpful Review
2 0
(4 out of 5 stars) Good product
Reviewed By: Ross S. from Fairfield, CT ()
Pros: Quality construction, features and efficiency
Cons: Price, setup documentation and non-standard dimensions
I would have given this 5 stars if the dimensions were not so different than standard pumps. That required all new plumbing. There was also no documentation as to how the pump needs to configured using the RS panel. Tech support is great however.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
The Jandy variable pump is as quite as we had hoped for and it runs like a charm. We are very happy making the switch.
Was this review helpful to you?
1 0
(5 out of 5 stars) Great Pump for Aqualink
Reviewed By: WaterMister from Orlando, FL ()
Pros: Energy Efficient, Large Plumbing Ports, Large Basket
Cons: None
This is a great variable speed pump, I was impressed by the shear size of this pump, it so much bigger than my Hayward Super II pump. Super Quiet and I lover the large inlet and outlet ports which accomodate 2.5" plumbing.
Was this review helpful to you?