Sta-Rite 60 sq ft Replacement Grid for S7MD60 DE Filter - 250230160S

$514.99

IN STOCK
FREE SHIPPING

Part # 250230160S

By Sta-Rite

  4.5 Average  

Details

Top

Part # 250230160S

Dimensions 15.5" L x 15.5" W x 25.5" D

Alternate Part #'s 25023-0160S, 14-102-1300, PEN25023-0160S, STA-06-276

Product Description

Sta Rite® Pool Filter Cartridges - Purchase a Replacement Cartridge for your Swimming Pool Filter or purchase a spare Cartridge.

Click here for more Sta Rite® Pool Filter Cartridge

Product Specifications

Filtration Area:
60 sq. ft.
Length:
25 - 1/4 in.
Diameter:
15 - 5/16 in.
Top

?     Asked on 9/2/2020by Gopal Das

Are there any less expensive cartridge part than part 250230160S ?
 Reply

A  Answered on 12/18/2020 by InyoPools Product Specialist Hector F.

Hi Gopal, unfortunately for this Sta-Rite System 3 Modular filter model S7MD60 this is the only replacement element that we carry. 
 Reply


?     Asked on 12/21/2019by James Brauch

For my Sta-Rite S7MD60 Lower Tank Shell: 1) Do the Baffle Screws 4ea (PN 37027-7028) come with the Relalcement Module (PN 25023-0160S)?
 Reply

A  Answered on 12/23/2019 by InyoPools Product Specialist Lennox H.

Hi James. The Baffle Kit w/ Screws - 23910-0013S is included with the S7MD60 Replacement Module - 25023-0160S
 Reply


?     Asked on 3/11/2018by Koala Tea Jarred

Does modular refer to the ability to use either to 60 or the 72 with the setup? If so, what factors determine the use of either the 60 vs 72? ...and, if I'm noticing my returns are blowing DE into the pool intermittently, as in 5 minutes it blows clean, and then 5 minutes dirty, and so on. Have you noticed that to be indicative of something specific orrrrrr.....?? Thanks.
 Reply

A  Answered on 3/13/2018 by InyoPools Product Specialist Lennox H.

Hi, Koala. You can use either the 60 or 72 replacement module in the same tank. DE blowing back into the pool could be signs of a bad module, o-ring, or air bleed assembly.  
 Reply


A  Answered on 2/24/2019 by Product Owner

I've noticed that happening to me before. I found the source of the problem was the backwash gaskets did not seat correctly when I turn the back wash off. I just had to reopen the backwash and reclose it. Your problem may be the seating of your O-Ring, if you see the Filter pressure is not at normal running levels. Good luck with your seatings on both.
 Reply


?     Asked on 6/25/2016by Inyo Visitor

I am having a problem holding pressure in my filter. Normally start up is 8 psi. The psi won't reach 5 psi. I cleaned my filter about a month ago and saw a crack on top of the filter. Would this cause the pump not to build up pressure in the tank?
 Reply

A  Answered on 6/30/2016 by InyoPools Product Specialist Alan M.

If you have damage, a crack or leak to the filter housing, this can absolutely cause the filter to not hold pressure.
 Reply


?     Asked on 8/4/2015by Inyo Visitor

does this filter comes with air breather
 Reply

A  Answered on 8/5/2015 by InyoPools Product Specialist Joe S.

Hello, Yes the Air Breather is included with the filter
 Reply


?     Asked on 7/11/2015by Laura

How often should this filter be replaced, if in use roughly four to five months out of each year?
 Reply

A  Answered on 7/12/2015 by InyoPools Product Specialist Patrick P.

Hi Laura, Normally we see the life span being 3 years or so. To determine when it is time to replace your DE grid you will want to note your initial clean starting PSI from your pressure gauge, when you install your new clean DE grid. You will know it is time to replace your grid when after you clean your grid the pressure does not drop below 10 PSI above your initial clean starting PSI. For example if the initial clean pressure reading is 10 PSI and 3 years from now you clean your grid and it does not drop below 20 PSI then it is time to replace your grid.
 Reply


Top

Review Summary

 (Average 4.5  out of 5 stars)
2 Rating
5 star:
 
(1)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews