Part # 5321-1
Warranty 1 Year
Manufacturer Code QC1072
Dimensions 13" L x 8" W x 6" D
Alternate Part #'s 1-168919-06, 10-168919-06, 16358, 165890, 168919, 5KCR38SN6147X, AE100DH, AE100DHL, AE100EL, AE100ELL, B2661, B661, B863, B863SE, C1447, C1499, C48A96B67, C48C23A03, C48C44B67, EB661, K48K2P100, K48K2P101, K48K2P101A1, K48K2PA101, K48K2PA101A1, K48K2PA105, K48K2PA105A1, K48K2PA105A2, K48K2PA105C1, K48K2PH100, K48K2PM100, K48K2PU100, QC1072, SQD75FL1E, 35-126-1172, AOS-60-5215, AOSQC1072
Voltage 115/230, Max Amps 115 Volts = 12.6 Max Amps 230 Volts = 6.3 , Service Factor 1.65, Single Speed, Square Flange, RPM = 3450, Threaded Shaft, Frame = 48Y Used on the following models: Sta-Rite Max-E-Glas, Max-E-Glas II, Dura-Glas, Dura-Glas II, Dyna-Glas, Dyna-Max Pentair Whisperflow, Pinnacle and Anthony AR2 Series.
Note: NOT California Title 20 Compliant.
California Title 20 Compliant Options:
I have a Sta Rite Max E Glas 3/4 horsepower pump, model # PE5D-181L, that is a single speed pump used for a waterfall and two fountains and I need a new motor, as the bearings in mine have gone out and it is very loud. The part # for the motor is K48K2PA105C1. Do you have one or one that is compatible?
Hello Ed. The Century Motors 3/4 HP Full Rate Motor QC1072 is the direct replacement for the motor model K48K2PA105C1. Century 3/4 HP Square Flange 48Y Full Rate EE Motor - QC1072 It is recommended that the motor shaft seal, seal plate gasket and diffuser o-ring be replaced concurrent with the new motor. The GOKIT54 (compatible with models 1998 to present) contains the necessary parts to complete this project. GOKIT54 Attached please find an exploded parts diagram for the Sta-Rite Max-E-Glas Pump for reference. Max-E-Glas
Replacing a STA-RITE MAX E PRO P6E6D-205L (k48k2pa105c1), is this 1-1 replacement? Gokit79? Anything else recommended?
Thanks in advance!
Hi Chris - the QC1072 motor will be a perfect replacement for the k48k2pa105c1 on your Sta-Rite Max-E-Pro Pump, and the GoKit79 Tune-Up Kit will let you replace all of the worn-out o-rings and the motor shaft seal when you change it out. Be sure to keep the sticker from the capacitor housing so you can remember what the model number of the pump is, but be careful if you remove the housing; the capacitor will hold an electric charge and can be dangerous.
Can you please help me with the tune up kit for this pump with a badly damaged label?
Thank you! i do have the cone and will discard it.
I just ordered this new pump do i need new seals
Hi, William. We recommend that you replace the shaft seal as well when you replace the motor. To determine the shaft seal you need, I would need the model number of your pump which is located on the plastic pump housing.
I am needing to replace an A.O. Smith #U27-1235 #K48K2PA105C1 motor with SF 1.65, HP .75, FR 48Y specs.
It is mated with a P4E6D-186L Max-e-glas lol pool pump. It was installed in 2001.
What is the best replacement motor for this and and more energy efficient with less amps used?
Is my old motor an ‘up rated’ or ‘full’ rated motor?
Hello, Does the #5321-1 come with the 'water slinger' rubber gasket or not? Thanks.
Is this the replacement motor for a Pentair Sta Rite P6E6D-205L Max E Pro 3/4 HP? Also need the tune up kit and strainer basket.
I have a sta-rite pump model # RE5D-181L. The motor started overheating at the end of last season. It looks like the QC1072 motor is the correct replacement, can you advise the pump-seal part #? I have attached a couple of reference pics.
Also - Does it make sense to just replace the motor, or should the whole pump be replaced?
Thank you, Rob
I’m trying to replace my K48K2PA101A1 Motor. What is everything I need to purchase?
This is the correct replacement motor and in order to locate the correct seal kit you will need to know the model name or number of the front pump housing that the motor actually bolts to. If you do not know that information then you can always take a picture of it and email that image to firstname.lastname@example.org.
I want to replace the bearings on my Century QC1072 (K48K2PA101A1); it's very noisy. Can you advise on the correct parts? I recently replaced the shaft seals however I suspect damage to the pump bearings occurred while the seals were leaking. Thank you!
this seems to be the exact motor i need to replace my VERY noisy existing one, that feeds my pools solar system. I am in the construction biz & fairly handy, i this something I could easily tackle replacing? Is the electrical complicated ? Do I need to purchase any additional parts other than pump - like gaskets etc?
Also I have NO room due to my existing pump being right up to a brick wall- will this slide out after bolts are removed ? Thanks for your help Bill
Yes, it is recommended to replace the seals and gaskets so you will need to know the model name or number of the front pump housing that the motor bolts to. If you are unable to locate that then you can email us pictures to email@example.com so we can advise. Also being that the pump is close to the wall it is tough to confirm whether you will have enough room but the motors do slide away from the housing.
can I use this motor as an energy efficient direct replacement for Part # 5231X By A. O. Smith ? this is connected to a purex triton ultraflow pump, model 38448300. also is there any maintenance kit for this pump I should install when replacing the motor?
I want to update the motor on sta-rite max-e-pro pentair water pool model: P6E6D-205L,
from .75 hp to 1.5 hp. what side of motor should I get 48Y or 56Y??
Hi, Tan. Either motor frame can be used. First, you will need to find out if your system can handle a 1.5 hp pump. Then replace the motor, impeller, diffuser, and seals.
I currently have a Sta-Rite Max-E-Glas II pump with a Sta-Rite motor model # K48K2PA105C1.
What motor would I order for this application please.
Yes, that would be the correct replacement motor and the GOKIT38 is the correct seal kit you need for your motor install.
Will this be a fit with my stay-rite max-e-glass ii pool pump?
Yes, that will fit your Max-E-Glas but I can ensure it is the correct replacement if you have your part number from your motor.
The motor that you suggested to replace my A.O Smith 1 HP K48K2PA105C, is a (B2853) and is rated at 3/4 HP, the max load reads 12.6/6.3 and my K48K2PA105C is rated at 13.8/6.9.
Losing 1/4 HP seems like it might have a hard time. I do have solar panels and I am concerned this might work this motor to much.
With that particular energy efficient motor you will not be saving a whole lot, but the two motor are basically the same. Both have a total horsepower of 1.25 so putting out the same horsepower.
I'm replacing the motor on my 1987 Hot Springs spa. It has a Sta-Rite Max-E-Glas pump PEXD-124UL and the motor is A.O.Smith K48K2PA101, 3/4HP. Please confirm that I need to order your QC1072. Also please advise which tune-up kit I should order for this pump.
Yes the QC1072 is the correct replacement motor for a K48K2PA101 motor.
I'm looking for a owner/service manual for this motor, model #K48K2PA101A1.
On the product page for the A.O. Smith 3/4 HP E.E. Square Flange Full Rate Motor (QC1072) in the documents section lists the Installation Guide and Trouble Shooting as well.
I am searching for the capacitor value (the one on top of this motor QC1072) It was damaged beyond identification (destroyed); Motor is used on a 3/4 HP water Pump Motor Model: C48C44B67; serial # 05008J2
What shaft seal do I need? I'm replacing an A.O. Smith motor (QC1072) that is coupled to a WhisperFlo Model WFE-3.
My old motor part no: K48K2PA105C1. It's matching a cross reference to this one (QC1072), however I couldn't fine my pump model number in the listing. Will this motor be exact fit for my pump Sta-Rite Max-E-Pro pump model: P6E6D-205L
Hello Stan. The A.O. Smith 3/4 HP E.E. Square Flange Full Rate Motor is an exact replacement fit for the Sta-Rite Max-E-Pro 3/4 HP Full Rate Energy Efficient, Model P6E6D-205L. When replacing the motor, we strongly recommend replacing the Shaft Seal. If you would like to replace all your pump seals, we have the Tune Up Kit Sta-Rite Max-E-Pro available as well.
Why should I purchase a Tune Up Kit?
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Why do I need to purchase a new shaft seal?
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
What is Service Factor?
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
1 to 2 hrs
Screwdriver, Nut Drivers, Pliers, Socket Set, strap wrench
Hit the old motor capacitor with a hammer a couple times, then ordered an identical replacement motor.
Received in a good amount of time. Unhooked the old, connected the new, and checked my wiring, hit the power switch and, drat, it hummed and smoked. Power off, Contacted INYO support, they suggested a few things. But seriously, it turned fine via a screwdriver at the end of the motor... Well, took it all apart and put it back together again. I swear, same as before, but this time it powered on it started right up and purred nice and quiet. That was over 2 months ago. Still running nice and quiet. Thanks!
Less than 1 hr
Screwdriver, Nut Drivers, Pliers, Socket Set, Wrench Set
(4 out of 5 stars) Just like the old one.
Reviewed By: Inyo Customer ()
Purrs and starts up like it's supposed to. This was an exact replacement of my previous motor that ran for 7 years. In 2004 I bought a Sta-Rite Max-E-Glas Pump, High Head, EE, Full Rated, 3/4 HP, 115/230v (PE5D-181L). In May of 2013 I bought a new motor: A.O. Smith 3/4 HP E.E. Square Flange Full Rate Motor (QC1072), 5321-1 (AOSQC1072) So, now, I hope to get at least another 7 years out of this one. 10 would be nice. Working great after the first 2 months.
(5 out of 5 stars) Excellent replacement motor.
Reviewed By: Barney B. from Champaign ()
Pros: Perfect fit, shipped in quick time, order tracking.
Cons: was not clear orders would ship together.
Excellent replacement motor fit perfect. Arrived in very quick time. perfect! It was not clear to me that the "Go Kit" would be included. I thought I read it may be shipped from another vendor and arrive at a different time. Tracking order was a good benefit also.
(5 out of 5 stars) Great price/Prompt delivery
Reviewed By: Robert from Asheville NC ()
Pros: Price, delivery, service,
Customer service helped us identify the right replacement pump when ours burned out. The price was right & it was delivered directly to our door in 2 days.