By Carvin


Details

Top

Part # 94027794

Alternate Part #'s 9402-7794, 94027794, S15LR-6-S1, S15LR6S1

Product Description

Jacuzzi SLR Pump

Patented air-cooled heat sink allows pump to run dry without damage to shaft seal. Exclusive Ring-Lok strainer allows "tool-free" access to strainer basket. Internal ribs in large strainer basket assure flow even when filled with leaves and debris.

    SLR 1.5 HP 6' Cord, 3 Prong Single Speed, 12O'Clock Vertical Discharge (94027794)
  • 60HZ
  • 115 Volt
  • 1.5 H.P.
  • 12.4 Amp 
  • 29 LBS 

Product Specifications

HP:
1-1/2 HP
Speed:
Single
Volts:
115 V
Amps:
12.4
Port Size:
1.5 in.
Cord Type:
6 foot/ 3 prong
Top

?     Asked on 4/2/2023by ROBIN N AYALA-URIONDO

is this an Inground or above ground pump
 Reply

A  Answered on 4/2/2023 by InyoPools Product Specialist Hector F.

Hello Robin, this pump is designed for above ground pool applications. 
 Reply


?     Asked on 4/27/2021by Gregg

Can you recommend a replacement pump for a Jacuzzi S15LRD? See attached pictures of the existing unit. Thanks, Gregg

 Reply

A  Answered on 5/1/2021 by InyoPools Product Specialist Patrick P.

Hi Gregg, We would recommend the PureLine PL1502 1.5 HP Pure Pro XL as a replacement pump. Please note the PL1502 is 115V and comes with a standard 3 Prong plug.
 Reply


?     Asked on 8/24/2018by Bill

Can I replace Jacuzzi S15LR-3-S1 Pump with AO Smith 7-177760-23 motor 1.5Hp -- with -- SLR 1.5 HP Pump Vertical Discharge - 94027794? The electrical spec is the same. The physical configuration seems similar. I need to make sure the hose connections are the same. How many RPMs? thank you, Bill
 Reply

A  Answered on 8/25/2018 by InyoPools Product Specialist Lennox H.

Hi, Bill. You can use this pump as a replacement for your S15LR-3-S1 model pump. 
 Reply


?     Asked on 5/11/2018by Inyo Visitor

can this pump replace my PENTAIR Dynamo 1 1/2 Hp for a 24ft round above ground pool
 Reply

A  Answered on 5/11/2018 by InyoPools Product Specialist Hector F.

As far as voltage and strength the two match but being two different lines the housing designs will be different. 
 Reply


?     Asked on 2/12/2018by Valentin

is this the correct replacement for 1LRC-5-48-S1/B ?? and do you ship this to King City, Ontario? total cost?
 Reply

A  Answered on 2/12/2018 by InyoPools Product Specialist Lennox H.

Hi, Valentin. This SLR pump will not replace the 1LRC. We do not sell a replacement for the 1LRC-5-48-S1/B. 
 Reply


?     Asked on 8/22/2017by Inyo Visitor

Do you sell the quick couplings for the discharge and inlet on the SLR 1.5 HP Pump Vertical Discharge ?
 Reply

A  Answered on 8/22/2017 by InyoPools Product Specialist Lennox H.

Hi. You can use the Union, S15uns Half, 1-1/2" Slip (31175607) - B0602-15 with this Carvin Pump.
 Reply


?     Asked on 7/29/2017by Michael Donnelly

Can this pump and motor assembly be converted to 230V if need be? If not what is your return policy?
 Reply

A  Answered on 7/30/2017 by InyoPools Product Specialist Alex V.

Michael, The SLR 1.5 HP Pump Vertical Discharge can only be set to 115v. 
 Reply


?     Asked on 7/28/2017by Michael Donnelly

Will this SLR pump replace my Jacuzzi Model # S15LRDV pump? It's approx 25,000 gal inground pool?
 Reply

A  Answered on 7/28/2017 by InyoPools Product Specialist Lennox H.

Hi, Michael. The correct replacement is model # 94027810. You can use this pump if the pump is operating on 115 Volts. 
 Reply


?     Asked on 6/18/2017by Danny Wilson

The skimmer bottom broke during the night and the pump ran dry for several hours. The pump now makes a high pitch sound when running. Is there a place where I can lube either the pump or motor to see if that will help?
 Reply

A  Answered on 6/25/2017 by InyoPools Product Specialist Lennox H.

Hi, Danny. Lubricating the current seals will not resolve the problem, I would recommend replacing them using the Jacuzzi LR Series Tune Up Kit - GOKIT41. The high pitch sound could be the bearings failing inside the motor.
 Reply


?     Asked on 5/30/2017by Inyo Visitor

i have a jacuzzi s15lr-s 230v dual speed pump for an inground pool. What is the replacement?
 Reply

A  Answered on 6/4/2017 by InyoPools Product Specialist Lennox H.

Hi. There is not an S15LR-S 230 volt dual speed pump replacement available. I would recommend the PureLine Prime Digital Dual Speed Pump - PL2607.
 Reply


?     Asked on 5/24/2017by Tony

We have a 18 x33 above ground pool waterway pump 1 hp 115 volt , will this pump be ok to use
 Reply

A  Answered on 5/24/2017 by InyoPools Product Specialist Patrick P.

Hi Tony, You could use this pump but you will have a little bit of re-plumbing. I would suggest this 1.5 HP Waterway Above ground Pool Pump as the plumbing will be easier.
 Reply


?     Asked on 5/22/2017by Tony

Need to replace pump , we have approximately a 13000 gallon above ground pool , currently a 1 hp motor is this particular motor to much or would it be a good choice . And what would be shipping time
 Reply

A  Answered on 5/28/2017 by InyoPools Product Specialist Lennox H.

Hi. Tony. This SLR pump can be used as a replacement if you have a large enough filter that can handle the water flow.  This item is instock and will ship within 1 business day.
 Reply


?     Asked on 4/2/2017by scott

Hi, I Have the S15LR-6-HK with the horizontal discharge.. Is there any reason why I can"t replace it with the vertical discharge model and just redo the piping considering its almost half the price?? Thanx, Scott
 Reply

A  Answered on 4/3/2017 by InyoPools Product Specialist Lennox H.

Hi, Scott. Yes, you can use the vertical discharge pump and redo the plumbing. You will also have to elevate the filter for efficiency.
 Reply


?     Asked on 3/23/2017by coachd

I have a 27 ft.(17000 gal.) above ground pool with a 2hp motor that needs replacing. Can I downsize to a 1 1/2 hp pump.
 Reply

A  Answered on 3/23/2017 by InyoPools Product Specialist Lennox H.

Hi, Coachd, Yes, you can downsize to a 1-1/2 HP pump if it can provide enough water flow to your pool. I don't think it will be an issue because most above ground pool is within 4 feet of the pool.
 Reply


?     Asked on 3/9/2017by kenny t

Will this replace a SP1580x15 hayward pump?
 Reply

A  Answered on 3/10/2017 by InyoPools Product Specialist Lennox H.

Hi, Kenny. Other than the discharge position on the SP1580X15 pump, the SLR can be used as a replacement.
 Reply


?     Asked on 1/13/2017by Kay

will this work for my splash pak sand filter model SS160-S1B-6-HK6..i know it is a 1.5 hp ..the one i have now is a 1hp but i have had to replace it ever couple of years..so i though the 1 1/2hp might benefit better..thanks, Kay
 Reply

A  Answered on 1/13/2017 by InyoPools Product Specialist Adam Y.

The 1.5hp isn't going to last longer it will have more flow. It will also cost more to run. I would recommend you stay with your current pump and just replace the motor. Unless, you want more flow. I would need to know where your current flow is at psi wise. You can get that off the pressure gauge on your filter.
 Reply


?     Asked on 9/23/2016by Bruce

Does this pump require a cover from the weather?
 Reply

A  Answered on 9/23/2016 by InyoPools Product Specialist Stacey M.

Hello Bruce, it's recommended any motor would benefit from a motor cover. Not required, but beneficial if its out in the elements.
 Reply


?     Asked on 8/24/2016by Jim Sturno

Can this motor run off of 220v ?
 Reply

A  Answered on 8/25/2016 by InyoPools Product Specialist Alan M.

Sorry but this pump is rated to run 115v only.
 Reply


?     Asked on 8/24/2016by Jim Sturno

Is the motor included?
 Reply

A  Answered on 8/26/2016 by InyoPools Product Specialist Lennox H.

Hi Jim, This is a complete pump which includes the motor.
 Reply


?     Asked on 7/21/2016by Henry

Will this pump operate a 52" x 26 foot with no problem of overheating or not pumping enough water to filter properly
 Reply

A  Answered on 7/21/2016 by InyoPools Product Specialist Scott W.

Yes, that pump will be sufficient for that size of pool.
 Reply


?     Asked on 7/12/2016by Inyo Visitor

is there a reset switch on this part. Having problems with the system staying on. Had someone to come out and change the outlet but it appears that it system has blown it again. Please advise.
 Reply

A  Answered on 7/17/2016 by InyoPools Product Specialist Lennox H.

Hi, These pumps are not equipped with a reset switch, the motor could be bad causing it to short out.
 Reply


?     Asked on 6/27/2016by Dean Lackey

What is the back pressure rating in gallons/minute for this pump? Thanks!
 Reply

A  Answered on 7/3/2016 by InyoPools Product Specialist Lennox H.

Hi Dean, There is not a  way to calculate back pressure unless it's installed. You can view the SLR Tech Sheet for performance info.
 Reply


?     Asked on 6/27/2016by Tracy

will this work off a 120-20amp breaker with a normal 3 prong plug or do I need a 240 breaker?
 Reply

A  Answered on 7/3/2016 by InyoPools Product Specialist Lennox H.

Hi Tracy, A 120 volt - 20 amp breaker is sufficient to operate this pump.
 Reply


?     Asked on 6/23/2016by george

what is the length overall and what is the inlet and outlet size, and are couplings included. flow chart please
 Reply

A  Answered on 6/24/2016 by InyoPools Product Specialist Megan C.

Hi, George. The over all length is 21", the suction/discharge include both 1.5" FNPT and 1.5" straight union connection. The unions are sold separately, Union, S15uns Half, 1-1/2" Slip (31175607)  PART#9173F .
 Reply


?     Asked on 6/16/2016by Joy

We have a JACUZZI model #S15LR-3 with 1 1/2 HP for our above ground pool. It leaks through cracks and it has 3450 RPM. Is this the replacement for it? at least would it suit our needs?
 Reply

A  Answered on 6/17/2016 by InyoPools Product Specialist Patrick P.

Hi Joy, as long as your pump had the discharge port coming out of the top of the pump then this would be the correct pump. The discharge port is the port that has the hose going to the filter, sometimes this is located on the side.
 Reply


?     Asked on 6/15/2016by Inyo Visitor

I have a Pentair Dynamo, will this work the same? Will everything fit the same?
 Reply

A  Answered on 6/21/2016 by InyoPools Product Specialist Lennox H.

Hi, This pump can replace a Pentair Dynamo pump, if you have a union hose we will need to know the part number because it might not thread onto this pump.
 Reply


?     Asked on 6/3/2016by Inyo Visitor

I have waterco supamite model 2401150u will this pump replace the waterco pump
 Reply

A  Answered on 6/9/2016 by InyoPools Product Specialist Lennox H.

Hi, This S15LR-6-S1 pump is a suitable replacement for the Waterco Supamite 2401150U pump.
 Reply


?     Asked on 5/28/2016by Scott

Is this a brand new motor and pump unit, or rebuilt?
 Reply

A  Answered on 5/28/2016 by InyoPools Product Specialist Joe S.

This unit is a brand new unit with full manufacturer's warranty.
 Reply


?     Asked on 5/26/2016by Angela

I have a model 1LRC-5-48-51. Is this pump compatible with this model?
 Reply

A  Answered on 5/27/2016 by InyoPools Product Specialist Scott W.

It could work. One has a cord and the other doesn't and one is a 1HP and the other is 1-1/2HP. As far as plumbing everything is the same but one of the motors gets wired and the other one you plug into an outlet.
 Reply


?     Asked on 5/25/2016by jeff

can it be used on a 18x36 inground pool?
 Reply

A  Answered on 5/25/2016 by InyoPools Product Specialist Dennis R.

Hi Jeff, No, this pump can only be used for above ground pools. They have to be installed below the surface of the pool so it can be gravity fed.
 Reply


?     Asked on 5/25/2016by Sherry

What is the voltage and hz?
 Reply

A  Answered on 5/25/2016 by InyoPools Product Specialist Hector F.

These are 60 HZ and 115 volt.
 Reply


?     Asked on 5/5/2016by Inyo Visitor

What inlet and outlet size fittings do i buy to attach to the pump?
 Reply

A  Answered on 5/5/2016 by InyoPools Product Specialist Charlie R.

The SLR Pump (94027794) inlet and discharge both are 1-1/2" NPT.
 Reply


?     Asked on 5/2/2016by richie

is this pump for an above ground pool?
 Reply

A  Answered on 5/5/2016 by InyoPools Product Specialist Charlie R.

Richie,Yes, the SLR Veritical discharge pump can be used for above ground pools.
 Reply


?     Asked on 4/16/2016by matt

Does this include the motor and everything pictured?
 Reply

A  Answered on 4/18/2016 by InyoPools Product Specialist Andy O.

Matt- The 94027794 SLR 1.5 HP Pump Vertical Discharge is the entire pump and motor as pictured.
 Reply


?     Asked on 1/19/2016by David

What is GPM rate?
 Reply

A  Answered on 1/19/2016 by InyoPools Product Specialist Andy O.

David- The SLR 1.5 HP Pump Vertical Discharge model 94027794 has a flow rate of approximately 65 gpm at 30 feet of head.
 Reply


?     Asked on 9/15/2015by Danny Wilson

Is the inlet and discharge both 1 1/2" NPT?
 Reply

A  Answered on 9/17/2015 by InyoPools Product Specialist Lennox H.

Hi Danny, The SLR Pump (94027794) inlet and discharge both are 1-1/2" NPT.
 Reply


?     Asked on 8/15/2015by Inyo Visitor

Can you please tell me if this is compatible to a S15LR3S1? My Serial # is 13858 on the pump I currently have. Thank you!
 Reply

A  Answered on 8/16/2015 by InyoPools Product Specialist Lennox H.

Hi, The SLR 1.5 HP Pump Vertical Discharge (94027794) is compatible to your S15LR3S1 Pump.
 Reply


?     Asked on 8/12/2015by Inyo Visitor

What size hose will this need to connect to skimmer & filter?
 Reply

A  Answered on 8/13/2015 by InyoPools Product Specialist Robert M.

A 1.5" diameter hose would be the correct size.
 Reply


?     Asked on 6/30/2015by Inyo Visitor

this price does include 1.5 hp motor, mounting bracket, etc. as shown in picture? does it not?
 Reply

A  Answered on 7/1/2015 by InyoPools Product Specialist Brian M.

The price for the Jacuzzi SLR 1.5 HP Pump Vertical Discharge does include everything in the picture.
 Reply


?     Asked on 6/28/2015by Slf

What is the warranty on this pump?
 Reply

A  Answered on 6/29/2015 by InyoPools Product Specialist Brian M.

This product has a 1 year warranty from the manufacturer
 Reply


?     Asked on 6/10/2015by Inyo Visitor

Will I be able to remove my twist lock plug from my burnt out jacuzzi and splice it to this new pump?
 Reply

A  Answered on 6/10/2015 by InyoPools Product Specialist Patrick P.

Yes you could use your old cord on the new pump. You would not need to splice as there should be spade connectors where the cord attaches and detatches so you should be able to loosen these to remove and re-apply cord.
 Reply


?     Asked on 5/10/2015by Inyo Visitor

When will above item ship and how long to get to zip 37659? And will it replace jac s15lr-6-s1?
 Reply

A  Answered on 5/10/2015 by InyoPools Product Specialist Patrick P.

This item is currently in stock and would take 3 to 5 business days to your ZIP Code. Yes this will replace the Jacuzzi S15LR-6-S1
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
3 Rating
5 star:
 
(3)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews