$399.99

Qty:

By Jacuzzi Inc.


Details

Top

Model # 94089250

Alternate Part #'s 9408-9250, 94089250, L250-7C, L2507C, 30-105-1020, JAC-05-9250

Product Description

Jacuzzi Laser Sand Filter

Features:

  • Three Models available 19" (48,3 cm), 22,5" (57,2 cm) and 25" (63,5 cm) models.
  • Upper distribution system integrated into the dial valve and engineered to direct water evenly across the entire surface of the sand – up to 25 gpm/sq.ft. (61 m 3 /h/m 2 ) without sand migration or channeling.
  • 7-way Dial Valve with "sight glass", automatic air relief, and pressure gauge. The 7 functions include : Filter, Backwash, Rinse, Whirlpool, Drain, Test & Winterize.
  • Non-Corrosive Resin Clamp for simple installation and service of dial valve and filter components.
  • Underdrain with "side-slotted" laterals draws water evenly across the full diameter of the sand bed for higher flows, better filtration, longer cycles and more efficient backwashing. Features heavy-duty, freeze resistant hub and easy-service "Snap-Fit" laterals.
  • Deep, high-capacity sand bed carries more debris and extends filter cycles.
  • Blow-molded tank is corrosion-resistant, and UV-resistant.
  • Bottom drain for winterizing and draining.
  • Hose and Hardware included.

Dimensions:

Performance:

Product Specifications

Tank Diameter:
25 in.
Pipe Size:
1-1/2" in.
Top

?     Asked on 1/27/2012by Guest

When should I change the sand in my filter?
 Reply

A  Answered on 1/27/2012 by InyoPools Product Specialist Patrick P.

You should change the sand in your filter every 5-7 years. You can generally tell that it is time if your pool water is not as clear as it normally is or when you notice the interval between backwashes is shorter. You can use > this guide to walk you through it.
 Reply


?     Asked on 3/1/2012by Guest

How often do I have to replace the sand in my filter? What is normal operating pressure?
 Reply

A  Answered on 3/1/2012 by InyoPools Product Specialist Patrick P.

On a "fresh start-up" a filter would operate anywhere between 10-20 psi. As a general rule of thumb you only want to backwash when the pressure increases 8-10 psi. You want to make certain that the pump is being turned off whenever you move the handle on the valve. Once backwashing is complete (3-5 minutes), you can switch to the rinse option to re-settle the sand bed. Sand will typically last 5-7 years. Premature backwashing will wear down the size of the sand which will cause difficulties such as cloudy water and higher operating pressures.
 Reply


?     Asked on 5/21/2016by BOB

I currently have a Jacuzzi DE filter, can I replace this with a Sand filter and what are the advantages or disadvantages of DE vs Sand?
 Reply

A  Answered on 5/22/2016 by InyoPools Product Specialist Hector F.

Yes you can go from a D.E. filter to sand but just keep in mind that you will be going from the best filtration to the least efficient. Also the sand filter may not be able to handle as much pressure. Sand is common in the north east market though. At least consider a cartridge filter which would be like taking the middle road.
 Reply


?     Asked on 5/24/2016by Inyo Visitor

Can I use this filter as a replacement for a SFTM 25. Why is it called a laser sand filter
 Reply

A  Answered on 5/24/2016 by InyoPools Product Specialist Lennox H.

Hi, This Jacuzzi Laser Sand Filter L250 can replace the Jandy SFTM25 filter. That's just the manufacturer's name of the filter.
 Reply


?     Asked on 6/12/2016by Harold

Would the L250-7C 25inch be powerful enough for an inground pool size 20 X 40
 Reply

A  Answered on 6/18/2016 by InyoPools Product Specialist Lennox H.

Hi Harold, The Laser L250 Can filter 31,700 gallons of water in an 8 hour time frame. if your 20' x 40' is less than 31,700 gallons this will be sufficient for your pool or you will need to run it longer.
 Reply


Top

Review Summary

 (Average 5  out of 5 stars)
4 Rating
5 star:
 
(4)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews