Jacuzzi Laser 22.5" Sand Filter W/ 1.5 HP Pump (94084968)

Part # 4625-204

  4.5 Average  



Part # 4625-204

Manufacturer Code 94084968

Alternate Part #'s 9408-4968, 94084968, L225C-7-S15LR6-HK6, L225C7S15LR6HK6

Product Description

Jacuzzi Laser Filter Systems With SLR Series Pump


  • 14" (35,6 cm), 16" (40,6 cm), 19" (48,3 cm) and 22,5" (57,2 cm) MODELS feature our Upper Distribution System integrated into the dial valve and engineered for optimum flow – up to 25 gpm/sq.ft. (61 m 3 /h/m 2 ) without sand migration or channeling.
  • Non-corrosive resin clamp assures simple installation and service of the 7-Way Dial Valve and filter components.
  • 14" (35,6 cm) laser models are available with 5-way valve.
  • Underdrain with side-slotted laterals draws water evenly across the full diameter of the sand bed for higher flows, better filtration, longer cycles and more efficient backwashing. Features heavy-duty, freeze resistant hub and easy-service Snap-Fit laterals.
  • Extra deep sand bed for extended filtration cycles.
  • Bottom Drain for winterizing and draining.
  • LR Series Pump with Ring-Lok™ access to strainer basket. Patented air cooled heat sink allows pump to run dry without damage to the shaft seal. UNCONDITIONAL TWO-YEAR WARRANTY AGAINST SEAL FAILURE.
  • 6 ft. (1,8 m) corded models feature a 3-prong, grounded plug.
  • 3 ft. (0,9 m) corded models feature the NEC twist-lock plug (UL listed pump).
  • Injection-molded, high quality platform base provides a non-corrosive elevated surface for sturdy support of pump and filter.
  • Maximum water temperature *104 °F (40 °C).


  • Pump: 1.5 HP Jacuzzi SLR
  • Cord: 6' Length with 3 Prong
  • Volts: 115V
  • Amps: 12.4
  • Filter: 22.5" Laser Sand Filter
  • Model: L225C-7

Product Specifications

Tank Diameter:
22.5 in.
1 - 1/2 HP

?     Asked on 4/5/2020by Matt

I have a 15 X 24 oval pool 52" high. I am just wondering if I need a 1.5 horsepower pump or would a 1 horsepower pump work. My jacuzzi on it now is 23 years old and the last two years the suction has not been great. I have always had a 1 hp pump. Not sure if it is a seal problem or the filter is just old and ready to be replaced.

A  Answered on 4/9/2020 by InyoPools Product Specialist Patrick P.

Hi Matt, Thats great that you have got 23 years out of your Jacuzzi Pool Filter System. Yes I would say it is time to be replaced, the Jacuzzi Filter System is no longer available through us and we would suggest this 1.5 HP PureLine Sand Filter System this would be the proper size for your pool.

?     Asked on 7/3/2017by Joseph F Harmon

hi have orginal pool filter /motor pool kickin sand into pool priced parts thinkin just replace everything have a jauczzi 190 lazer will this work (inground 26 ft octogan 5ft deep

A  Answered on 7/13/2017 by InyoPools Product Specialist Stacey M.

Hello Joseph, For an inground unit Hayward Super Pump 1 HP Single Speed W/ S244T 24" Sand Filter & Valve - SP2607X10S244T would be more appropriate for an inground 26 octogan. The  Jacuzzi Laser 22.5" Sand Filter W/ 1.5 HP Pump (94084968) are more appropriate for an above ground unit.

?     Asked on 6/9/2017by Dave Hartwig

Would this model be good for a 15x30 x52" tall above ground or could I go with a smaller model to do the same job.

A  Answered on 6/11/2017 by InyoPools Product Specialist Lennox H.

Hi, Dave. This Jacuzzi Laser 22.5" Sand Filter W/ 1.5 HP Pump - 94084968 will be sufficient for a 15' x 30' x 52" above ground pool. A smaller filter and pump can also do the job with a longer run time.

?     Asked on 6/7/2017by JORGE ELIAS WATED

this item has unionized pump to filter connection

A  Answered on 6/24/2017 by InyoPools Product Specialist Lennox H.

Hi, Jorge. The pump to filter hose does not have unions, it uses adapters with stainless steel clamps. 

?     Asked on 5/28/2017by Ken

We have a inground pool (15 x 35) with a Hayward ST220 filter and I think Super pump with 1 HP motor. The motor failed the pump seals again, replacement seals installed yesterday are leaking a bit. The motor shaft has some wear on it and was stuck when we moved in 2 years ago. Filter occasionally blows sand into pool after a backwash. We are using a salt water system on the pool. If I were to just go ahead and replace the system, would this be appropriate replacement?

A  Answered on 6/1/2017 by InyoPools Product Specialist Lennox H.

Hi, Ken. This is not an appropriate system is for an inground pool. It will not work if the water level of the pool if lower than the pump inlet.

?     Asked on 4/5/2017by Steve

Does this pump and filter have the two speed pump, if not which one does and is it a advantage to have?

A  Answered on 4/6/2017 by InyoPools Product Specialist Scott W.

A good pump/filter combo with a pump that is dual speed is part number 52252406S. The advantage is putting it on low speed when you are just circulating your water to save on your energy bill and turn on high speed when you need more pressure like if you have your suction side cleaner running.

?     Asked on 2/17/2017by DAVE

Can I get the system with a motor that runs on 220 volt. I would rather have a pump that runs on 220 volts.

A  Answered on 2/17/2017 by InyoPools Product Specialist Megan C.

The alternative is to install inground pool equipment, you may like to review the Hayward Super Pump 1 HP Single Speed W/ S244T 24" Sand Filter & Valve - SP2607X10S244T or click here to view all Hayward Inground Pump & Filter Systems.

?     Asked on 2/17/2017by dave

Can I get the pump to run on 220?

A  Answered on 2/17/2017 by InyoPools Product Specialist Andy O.

Hello Dave- No you can not, this pump is for 115v only.

?     Asked on 9/5/2016by Steve

I have a 15x30 inground 'oval' pool would this system work??

A  Answered on 9/7/2016 by InyoPools Product Specialist Lennox H.

Hi Steve, This pump and filter package will not be sufficient for an inground pool.

?     Asked on 6/5/2016by Valerie Kephart

Hi. I have an in ground pool about 15.000 gals. Depth 3.5 ft. to 7 ft.. Would this product work for me? If not could you make a recommendation? My cartridge system consists of 4 ea. 20 micron filters of 81 sq. ft. filtration area for each. How big of a sand system ans size of sand would i need

A  Answered on 6/5/2016 by InyoPools Product Specialist Patrick P.

Hi Valerie, this system would not work on an inground pool as it is not a self-priming pump. You need a self priming pump on an inground pool as normally inground pool equipment is above the water level of the pool. For a 15,000 gallon pool we would suggest a PureLine 1.5 HP Pure Water Pump along with a S244T 24" Sand Filter.

?     Asked on 5/30/2016by Lynn

Will this work 27 round by 54 deep

A  Answered on 5/30/2016 by InyoPools Product Specialist Patrick P.

Hi Lynn, Yes the Jacuzzi Laser 22.5" Sand Filter W/ 1.5 HP Pump would work on a 27' Round 54" Pool.

?     Asked on 5/21/2016by Dustin

Will this work for a 33 foot diameter pool, 54 inch depth?

A  Answered on 5/21/2016 by InyoPools Product Specialist Patrick P.

Hi Dustin, Yes this would be a great choice for a 33' 54" pool.

?     Asked on 5/19/2016by Inyo Visitor

We have a 30' foot round above ground pool. 52" deep will this work?

A  Answered on 5/20/2016 by InyoPools Product Specialist Lennox H.

Hi, This system will work with a 30' round above ground pool.

?     Asked on 4/15/2016by Rene

I have a inground pool that is about 10,000 in size, and the pipes are 2". Will this product work for me?

A  Answered on 4/15/2016 by InyoPools Product Specialist Hector F.

Yes this pump and filter is sufficient fore your pool. You may need to reduce the plumbing to 1.5 inch at the valve and pump ports though.


Review Summary

 (Average 4.5  out of 5 stars)
2 Rating
5 star:
4 star:
3 star:
2 star:
1 star:

The Most Recent Reviews