Why should I purchase the heavy duty seal?
Reply
The heavy duty shaft seal features carbon graphite, stainless steel, and Viton rubber. The properties of this seal contribute to the resistance of chemical corrosion. This is the best choice for salt chlorine generators or ozonators.
Reply
How do I change the shaft seal on my pool pump?
Reply
Changing the shaft seal is quite simple. Here's How To Replace a Pool Motor Shaft Seal.
Reply
should I replace the seal every time I replace the motor?
Reply
Yes we suggest replacing the shaft seal whenever you replace your motor as the old seal sometimes does not mate up properly with the new motor. Also the warranty on the motor is voided is there is leaking to due the seal.
Reply
will this fit ao smith 1 hp square flag 56y motor
Reply
It will depend on the model of your pump, not your motor. The motor can go to several different model pumps, so would need to know the model of your pump to determine the correct shaft seal.
Reply
Which side of the spring loaded piece touches the ceramic disc on the second piece on a ps 3867.?
Reply
Hi, The shaft seal should be installed ceramic against ceramic. You can view our How To: Replace a Pool Motor Shaft Seal for instruction.
Reply
What is the difference between a chlorine pool and a soft water with regard to the seal?
Reply
Dan, Salt-water is more corrosive to equipment so it is recommended to use a heavy duty shaft seal. Other wise, the seal will fail prematurely and cause damage to the motor.
Reply
Just want to confirm that this is the same as SPX2700SA, but for saltwater pools.
Reply
What is the correct shaft seal replacement part for a Hayward Super pump II with a salt system. The service technician will replace all the required O-rings. If I purchase a replacement motor and a new shaft seal, is there anything else that I need to purchase for the tech. (besides O-rings)
Reply
Wath pump seal do i need for a intex 633m 2500 w timer above pool and or for a sand filter pump SF80110 ,I have 2 but use the same ones .
Hi, Omar. We do not know which shaft seal used with that Intex Pump. You will need to contact Intex 1(800)234-6839.
Reply
I have a PEA6F-182L model with C103-193P Seal Plate, C105-137PEB impeller and USQ1152 Motor. Just want to be sure this is the correct seal. The "Seal Plate Kit - C203-193P" showed a different seal.
Reply
Hi Chris, yes this is the correct shaft seal for the Sta-Rite Dura Glas/ Max E Glass pump series. Just keep in mind that if you have the copper cone insert in the seal plate then it will need to be removed for this shaft seal to fit.
Reply
I'm looking for Shaft seal, Diffuser 0 ring and House 0 ring for a Hayward Max -Flo XL Pump. Motor, Century SQS1152R
1.5,Salt water pool.Can you send to me? You have in my account my cc #
Thank's
Reply
Hi Antonio, please see this Hayward Max Fo XL parts diagram where key numbers 7, 11, and 12 are the seals and gaskets that you are needing.
Reply
Is this the proper shaft seal for Century 1.5 HP Square Flange 56Y Up Rate Motor - B2854?
Is there a salt water substitute for GOKIT78?
Reply
Hello Richard. Additional information would be necessary in order to determine if this is the correct shaft seal for your project. Shaft seals are specific to the pool pump manufacturer and pump model, not the motor itself. If you could provide pump manufacturer and model information, a determination could be made as to the correct shaft seal replacement. There is no saltwater substitute for the GOKIT78. A heavy-duty shaft seal (saltwater pools) is available separately: PS-3867 Pump Shaft Seal Heavy Duty (Saltwater Pools) - PS-3867
Reply
Will this seal fit a Polaris PB4-60 pre-2011 booster pump for a saltwater pool? The diameter of the shaft seal sold with the PB4-60 is too small for my shaft
Reply
Good afternoon Marc, That part number 5250-210 is not the correct shaft seal based on the information you provided. If you have a pb4-60 then the correct shaft seal would be the Pump Shaft Seal PS-1000, Heavy Duty (Saltwater Pools) - PS-3865
Reply
