What is the voltage on this unit? How long is the manufactures warranty? If the system requires repairs during warranty, what do I do?
Reply
This pump runs on 115V power. This unit comes with a 1 year manufacturer's warranty. If the pump needed repair, you would call Hayward directly and they would put you in touch with a warranty service station in your area.
Reply
How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
Have this pump for my pool above ground. Looking for parts need the impeller and of course seals, gaskets etc. can't seem to locate it and when I did it the cost was insane.You have this part
Reply
Hi Bo. The part number for the 3/4 HP impeller is (5111-07D) it's listed at 32.99. The part number for the 1 HP impeller is (5111-07F) it's listed at 33.99. The seals and gaskets are sold individually. Strainer Cover O-ring 5111-84. $16.99. Diffuser O-ring (5111-77) 15.99. O-ring Housing (5111-80) 25.99. HAYWARD SHAFT SEAL (OEM) (SP1500KA) 28.99
Reply
Hello I asked this question about the impeller for the hayward pool pump but the answer you gave me back was for an 3/4 and 1 horse pumps, I have a 1.5 pump. I need the impeller and all the gaskets, seals, grease to install it. Again what is says on my pump is hayward matrix power flow 1.5 Sp 1593 what else might you need. Is there a kit that has all involved or just separate
Reply
Hi Bo sorry for any confusion, it looks like Hayward uses the same impeller for both there 1 HP, 1-1/2 HP and 2 HP Matrix pumps, which is this Matrix Impeller. The seals and gaskets are sold individually and not as a kit and all of those items were listed in the last reply with links to each product, those items will be all that you need.
Reply
Is there a cheaper replacement pump an motor than the power flo matrix that hooks up the dame
Reply
Hi Terry, This 1-1/2 HP Above Ground Pool Pump would be a good alternative to the Hayward Power Flo Matrix. I would double check the Port Locations & Dimensions on the pump I supplied to make sure it will work with your set up.
Reply
I need an o-ring for the pot (strainer) of this pump. About 7" OD. All the O-Rings I've found are about 5 1/2" OD. Can you help me find one?
Reply
Ed, Yes. We carry the Hayward Matrix strainer cover o-ring.
Reply
I had the basket off to look at the impeller it didnt spin real free. This pump run really good for about month. It is 2 year old now it has weak pressure. I back wash many times. The sand is 2 years old. What do you think
Reply
Mark - You might have to take the motor out of the pump housing to see why the impeller is not spinning freely. It may be cracked or loose or debris might be clogging it. Also check the diffuser. When you have the motor out and the impeller still doesn't spin freely, your motor bearings may be bad. See our guide on "How To Replace A Pool Pump Impeller" for information on pulling out the motor. You will not have to replace the impeller just ot look at it.
Reply
I need to order the strainer cover for a Hayward pump model # sp1593, power flo matrix, 1 1/2 hp. I do not need the whole pump but cannot find just parts on your website.
Reply
Hello Sue, the replacement Hayward Matrix Strainer cover is part number SPX5500D. If you needing any more parts, please review the Hayward Matrix Parts Breakdown.
Reply
Will this pump work with an In-ground pool ? or is it strictly for above ground pools? I have an in-ground and the pump only has to lift the water 8 to 10 inchs. will this pump work for me ?
Reply
Hi Bernard, This pump can not be used with an in-ground pool, only above ground pools.
Reply
Is the Hayward Perflex Series Extended Cycle Basic Filter Unit models EC65A and
EC75A compatible with the Hayward Matrix Swimming Pool Pump 1.5 HP (SP1593)?
Reply
Hi Russ, You can use the Hayward Matrix pump with EC75A filter if you have an above ground pool. The Matrix pump can not be used on an in-ground pool.
Reply
My 1.5 HP Hayward SP1515Z2es is squealing and I suspect the front motor bearing? What is the current Hayward replacement model for this particular motor/pump? What is the part # for the front bearings of my current motor and the four very long motor screws that hold the pump in place? I plan to replace my motor/pump but would like to attempt to repair my old for backup purposes. Thanks
Reply
Hi Bob, The Hayward Matrix Pump 1.5 HP Dual Speed-SP15932S is the correct replacement pump. We're unable to get the bearings and thru bolt for the SPX1515Z2ES motor, you can try contacting Hayward at 908.355.7995.
Reply
I need to replace the pump for my Hayward PowerFlo Matrix (model #SP15931CNP and Serial # 21121302005265001) what are compatible motors? I already bought one that the installer said was the wrong one.
Reply
Wendy, You can view replacement motors for the Matrix pump here: http://www.inyopools.com/pool_parts_hayward_matrix_pump.aspx
Reply
My SP1593FP pump motor went out, and i found an SP1580X15 pump locally. From what I found online the output is very close to each other. But when I hooked up the 1580X15 to the 27 ft diameter above ground pool, the flow is hardly enough to even hold the vacuum adapter and dos win place when I vacuum the pool.
Reply
Hi Tom, You might need to check and or clean out the filter to see if that is causing the low suction problem.
Reply
How you determine horsepower for pump? My pool has 20,000 gal.
Reply
Hi, Rolando. The pump size would be based on the size of the pool, location of the pump, filter size and whether you have any additional features. For a 20,000 gallon above ground pool with a large enough filter can use a 1.5 HP pump.
Reply
i need a diagram to show me how to hook up my cord to the pump
Reply
Hi, Lana. There is a wiring diagram located on the motor. The BLACK wire will go to the LINE terminal, the WHITE wire will go to the NEUTRAL terminal and the GREEN wire to the GREEN screw.
Reply
Our Hayward Swimpro Voyager pump went out and I need to know what I should replace it with since they don't make this pump anymore. We have a 32" circular, 22,000 gallon above ground pool with a larger vertical filter and heater. The pump is located approximately 10- 15 ft from the pool.
Thank you!
Reply
Hi Susan, This Hayward 1.5 HP Matrix Pump would be the pump we would suggest as a replacement for the Hayward Voyager system on a pool of your size.
Reply
What is the operating cost per day for the Hayward 1593 PowerFlo Matrix Pump....we have been advised to run our pool pump 24/7 and I would like to get an idea how much it will add to our electric bill.....our kwh cost is .14.
Reply
Hi, Mary. This pump will cost $5.80 per day to operate based on your energy rate.
Reply
I have a 35,000 gallon, inground pool. Salt water system. I need a new pump. Will this pump handle it? Does the pump have a saltwater seal?
Reply
Hi, Jeff. This pump will not be able to handle an inground pool application. This is an above ground pool pump. This pump does not have a saltwater seal, however, it can be used with a saltwater pool.
Reply
Hi, The switch on my programmable pump has broken. I am unsure as to how I can get a replacement. Any ideas?
Thanks
Reply
Hello Tom- If you need just the switch you would need the On Off Motor Switch (spx1500s8). The whole back portion of the motor that includes the timer is Hayward Above Ground Pool Pump Timer Microprocessor - SP1500FT but is no longer available.
Reply
The pump is missing from a pool I was given I have a Intex 22x52 above ground, sand filter with Praher multiport tm-12-L and Intex saltwater system. What pump should I get to fit hoses and size of pool. TY
Reply
Hi, Loedi. We will need to know the make and model of the sand filter tank in order to size a pump for your pool.
Reply
I have a Hayward power flo matrix 1.5hp 115 volts 15 amp. It is currently not working. What is the best replacement for this that is inexpensive? Thanks
Reply
I have a Hayward pump Modle#SP1593
1.5HP
115 volts
15.0 Amps
My plug is no good and I need to order a new one. It is shorting out my outlet. He promgs in the plug are burnt. Do you have a replacement plug I can purchase
Reply
Hi, Tom. You can use either the Standard 3-Prong - PL3547 or Twist Lock - 3-Prong 3' Pump Power Cord - SPX1550WA1.
Reply
Currently have an SP15931TLFP; which pumps can be used for replacement
Jo, I would suggest either the PowerFlo Matrix Pump 1.5 HP - SP1593 or the Power-Flo LX 1 1/2 HP, 115V, 1 Spd. Pump - W3SP1580X15 to replace your existing SP15931TLFP pump.
Reply
what size timer do you need for may PowerFlo Pump 1.5 hp ?
Reply
Hi Bill, I would suggest using any Internmatic 110 volt pool timer that you can view by clicking here.
Reply
I currently have a Hayward Power Flo Matrix sp1515-Z-1-ESC that died on me at the end of last season. As I open the pool this seasonI am looking to purchase a new pool pump. What pool pump would be the best and right replacement for my current pump? Thanks,
The PowerFlo Matrix Pump 1.5 HP - SP1593 - W3SP1593 or PowerFlo Matrix Pump 1.5 HP Dual Speed - SP15932S - W3SP15932S The dual speed is required for California orders, they must adhere to Title 20 Compliance.
Reply
.i have a hayward power-flo matrix SP1510Z1XEHC what pump would be best to replace it with?
Reply
Would this pump be a good fit with the Hayward C-550 cartridge filter?
Reply
Hi Emily as long as you have an above ground pool and your pump will be placed below the water level of your pool then yes this would be a good fit for the C-550 filter.
Reply
CAN THIS PUMP BE CONVERTED TO HORIZONTAL DISCHARGE?
Reply
Hi, John. Yes, the discharge of this pump can be rotated horizontally. Instructions are available in our How To Rotate the discharge port on your Hayward Matrix Pump Guide.
Reply
What size are the input and output screw connections?
Reply
Hello Ronald. The Hayward 1.5 Power-Flo Matrix Pump, Above Ground Pool, 115 Volt - W3SP1593 has a 1.5" diameter inlet/outlet port size. The Hayward Union Connectors (Set Of 2) - SP1500UNPAK2 are compatible with the external inlet/outlet port threads. Attached please find the Hayward PowerFlo Matrix Pump exploded parts diagram for reference.
Reply
