I need to replace my the capacitor on my 1.5HP pool pump. Do you carry the capacitor I need?
Reply
Please note that capacitors store an electric charge and should be handled with the utmost caution and care. We do not encourage handling a capacitor without any type of safety measures in place and highly recommend contacting a professional service company for repair/replacement. For those that feel comfortable changing the capacitor here's >How to replace a pool pump capacitor. In order to match up the capacitor you will need more specifications on the capacitor. You will need to match the voltage, the MFD, whether or not the capacitor is a >run or >start type and the actual dimensions of the capacitor body.
Reply
I need to replace the start Capacitor on my A O Smith C48K2PA105C5 MOTOR.
It's 115/230 1hp USQ 1102 and the rating are unreadable on the capacitor.
How can I find out what rating I need?
Reply
Hi Steve, yes this is the correct start capacitor for the USQ1102 motor.
Reply
I need a capacitor for a Jacuzzi pool pump, A. O. Smith 1.5 hp 230/115v 3450RPM. Can you tell me the correct part number for this product?
Reply
Bryan, We will need to know the MFD and voltage of the capacitor or the catalog or part number of the motor to find the correct replacement capacitor.
Reply
Century motor 3.HP cat # SQ1302V1 I need to replace run start capacitor Can you tell me what one I need.
Thanks
Mike
Reply
Hi, Unfortunately we do not have what size capacitor is used on the A.O. Smith 3 H.P Square Flange Motor (SQ1302), you will need to provide us the specs off of the old capacitor.
Reply
Hello, I am tryong to find out which starter capacitor I need for a 1 HP Hayward Super Pump, self priming, 193E, Model C48K2N143B1. Thank you
Reply
Hi Dax, The 161-193 MFD 110-125 VAC Capacitor (BC-161) would be the correct capacitor for the C48K2N143B1 model motor.
Reply
I am looking for a replacement capacitor for 189-227MFD 110V AC 60HZ
can you recommend the correct one?
Reply
Hi Jay, The 189-227 MFD 120 V Start Capacitor (BC-189) will be the correct replacement capacitor.
Reply
I'm looking for part # 610807-11 capicitor
Reply
Hi Al, The 36-43 MFD 220-250v Start Capacitor will be the replacement capacitor for p/n 610807-11.
Reply
I'm looking for a replacement for what appears to be part number 680171-002, rated 161-192 mF. It is from and A.O. Smith 1HP single speed pump. There are a ton of other numbers on the old one, so I hope this is enough. It looks like a BC-161 will be it, but I want to be sure.
Reply
Hi Mark, This capacitor is the correct replacement for p/n 680171-002.
Reply
I need a new start capacitor for an a.o. smith C48L2P104 sta-rite 1-1/2 hp two speed. The numbers are worn off but looks something like 61XXXX-002. Can you verify what the capacitor part is? Thanks.
Reply
Hi Tom, The 64-77 MFD 220V Start Capacitor (BC-64M-250S) will be the correct start capacitor for C48L2P104 motor.
Reply
hi. I am trying to find a replacement motor start capacitor for pool pump it is a Doheny's 1.5 hp, 115/230v capacitor I removed was a NGM61b1D220124NNCA 124-148uf . motor set in 220v. 2 3/4 L x 1 7/16 w having trouble finding in 220v
Reply
Hi John, Just because the motor is set for 230 volts does not mean that you need a 220 volt capacitor. What is the voltage on the capacitor because I'm unable to find a 124-148 MFD 220 volt capacitor.
Reply
Which start capacitor do I need for Hayward super pump model c48j2n131b1. thank you
Reply
The correct start replacement start capacitor for the C48J2N131B1 (UST1072) is the BC-124, 124-149 Mfd 125v.
Reply
I am looking for a start capacitor for a 1hp ao smith usq1072 cd6ob1be124148aut-2... 124-148uf 50/60hz
Reply
I think you answered this in a previous question but I just want to make sure, I have a Hayward Super Pump C48L2N134B1 it is configured in 220V. Is the BC161 for both 220 AND 115 V configurations.
Reply
Yes, that would be the correct capacitor for that motor whether it's wired 115V or 220V.
Reply
I have a jandy plus hp.I am trying to find a start capicator for it. The model nunber is PHPM2.0 and the serial number is u13fc1567 and if you guys have any in stock.thank you
Reply
I am trying to confirm that it is the capacitor that is the problem and that the correct capacitor will be replaced. I have a marathon 5KC38SN6084AX, the has hummed for a while prior to starting, but now it only humms but does not start. there is no oil leakage or whole that i can see, and sometimes it starts, usually not in cold weather.
Reply
Yes Chris, Sounds like the capacitor. You will need the UF or MFD number off of your capacitor to identify the correct replacement.
Reply
Using a Multimeter, how can I determine that my capacitor is my problem and not something else, what setting and what reading. The pump hums but does not start, I understand that the problem could either be the capacitor or the motor itself. My capacitor is only about 4 months old, has a 161-193 MFD.
Thanks, David
Reply
Good afternoon David, Unfortunately there is no instructions on our site. You can find a few videos that show you how on you tube.
Reply
The start Capacitor blew up, I have a new one rated 161-193 MFD. I believe the pump is wired on a 220 VAC. I can no longer read the weather erased old capacitor. Can I install a 110VAC capacitor on a 220 volt running motor?
Reply
Hi, Dom. Most start capacitors for pool motors are rated at 125 volts. You can install an 110VAC start capacitor on a motor that is wored for 220 volts.
Reply
I am in the UK. I have an old Sta Rite pump. I think the capacitor isn't working as I am getting a humming sound but the pump doesn't start turning. The capacitor is Mepco/CentraLab 161-193MFD 110VAC 60Hz. It says replace with part 610807-2. Will this capacitor work?
Thanks
Reply
Hi, Mike. Based on the info provided from the existing motor capacitor, this BC-161 can be used as a replacement.
Reply
how do I know what capacitor to get when mine does not have a MFD number. The numbers on mine are NGM 61B1D 110161NNMO 161uf. 40/065/21 -0% + 20% 610807-002
Reply
Kevin, What is the make, model and age of the motor?
Reply
My Sta-Rite pump has a Mallory start Capacitor, label reads: 161-192MFD 110VAC, 610807-2 60HZ, 235-0027-01A. Which part number should I order?
Reply
Hi, Jim. This 161-193 MFD 110-125VAC Start Capacitor is the correct replacement that you can order.
Reply
I need a replacement for my Jucuzzi magnum force pool pump capacitor 161-192uf 110 vac 50/ 60hz
Reply
The Capacitor, MFD 161-193 (BC-161) 110-125VAC is suitable based on the specs that you provided. Please ensure to check the measurements are the same before ordering. The measurements of this capacitor are 1.5" L X 1.5" W X 3" D. How To Replace a Pool Pump Capacitor
Reply
What will be the proper replacement , the following is the information on the existing capacitor: CSC 325P306H37M30A4XAO,
628318-308
SH P2
30.0uf +-6% 370VAC/B
50/60 Hz internally protected 70C
Reply
Hi, Tim. This is not the correct capacitor, you will need the 30 MFD, 370 VAC Run Capacitor - 628318-308.
Reply
I have Hayward Superpump model C48L2N134B1 volt 115/230 RPM 3450 KW 1.10 HP 1 1/2 60hz SF 1.0 FR 56J PH 1 SP1610Z1M. Will this Start Capacitor work?
Reply
Yes, this is the correct capacitor for that motor.
Reply
looking to buy a new capacitor but wanted to try and move shaft first to see if its stuck , cant find any info on how to do that with a hayward super pump model #c48l2n134b1
the cap is 61b1d110161nnmo 110v ac 60hz, 161-193 mfd
Reply
If you click here you can view how to replace a capacitor that is on a motor very similar to yours. Also by clicking here, you will be directed to a guide for replacing an impeller. In that guide, you will see a few tips on how to grab the shaft at the rear of the motor. The replacement capacitor is part number 5270-14.
Reply
I have a 1.6 hp Hayward super pump. The pump starts, but within seconds trips the breaker. I have changed the circuit that it plugs into, and it tripped that one as well. When I took the housing off I could smell burning but couldn’t locate any singed wires. Could it be the capacitor? If not, is there something else I can look at?
Reply
Hi, Jen. The issue could be the capacitor or the winding. Use the following guides How to Test a Pool Pump Capacitor or How To Test a Pool Pump Motor - Winding Resistance to determine why your motor is tripping the breaker.
Reply
Can you please tell me which capacitor will fit and work with my Hayward super-pump 1HP model # C48K2N143B1 so I can order it form you.
Thanks
Reply
Hi, William. This BC-161 Start Capacitor is the correct replacement for MOD C48K2N143B1.
Reply
I have a Mallory 161-192 MFD starting capacitor. Will the 161-193 MFD work as a replacement? What is the difference?
Reply
Hi, Frank. Yes, you can use this capacitor if the current voltage is 110-125 volts. The 161-193 is slightly more powerful.
Reply
looking for starting cap for a C48L2N134C2 -- everything comes up with a 5270-14 cap but its for a 115 volt motor -- we have it on the high voltage -- will it work -- over the long term?
Reply
Hi, Russ. This is the correct replacement capacitor. The capacitor voltage is not relevant to the motor operating voltage.
Reply
I have Jet table saw with 13/4 h.p. CapacitorCAP 200 MFD. W.V. 125 V AC. .made by Ming Fun Electric Co. Ltd.
Thank you, David.
Reply
Hi. Unfortunately, we do not carry a replacement capacitor based on those specs.
Reply
I have a Hayward skimmer pump 1HP the capacitor needs replacing No. 61B1D110161NNAO WILL THIS CAPACITOR WORK what is the difference in the A & O for the part number
Reply
Hello, What is the model number of the motor? If you are unsure, can you please take a picture of the motor label?
Reply
Harris in-ground pump #156589 1.5 hp. Motor Start Capacitor by NGM 124-148 Part # 61B1D220124NNCA. Is this the right capacitor. Size is correct.
Reply
My 1hp Hayward pump would only hum and not start. I replaced the starter capacitor with the BC-161 I ordered from y’all. Now the motor runs for a few seconds and trips the breaker. Do I need a new motor or is there a run capacitor I don’t know about?
Reply
Hi, Dennis. Some motors are designed with either a start or run capacitor or both. If the motor is now tripping the breaker, it will need to be replaced.
Reply
I have a Hayward in ground Super pump 1hp (6 years old) that when i opened my pool yesterday just hummed. I think from looking around that i might need a start capacitor!? mine i took a picture of has a number on it 161--192 and a big number 61B1D110161NNCA. Do you have a replacment for this? Will your 161-193 MFD work for my pump? HELP!!
Reply
Hello, Can you please take a picture of the motor label so we can find the correct capacitor for you?
Reply
I have a Emerson 1081 pool pump model T55CXCJ-1345 that won’t start. The motor hums but won’t start . Could the capacitor on the top of the motor be the problem?
Reply
Yes, this would be the correct unit and the cheapest route to take.
Reply
Hello - I have a Hayward SP2607x10 1HP pump, and am getting a humming noise at times when starting. It eventually starts, but I think I am getting close to having to replace something. I figured I could try replacing the start capacitor, can you help confirm exactly what part number I could use?
Reply
Hi Jason, the start capacitor on this page would be the correct capacitor for your Hayward SP2607x10 1HP pump
Reply
I have a Hayward Model C48L2N134B1 1 1/2 hp Super pump.
Is this the correct capacitor for that model?
Here's what came out.
I have a magnatek 3/4 pump on my Polaris pool cleaner. Will the bc-161 work to replace my 124-149 MFD capacitor 0-125 volt capacitor
Reply
Hi Jon, This is NOT the proper capacitor for your polaris cleaner motor, you will need this BC-124 124-149 MFD Start Capacitor
Reply
my pool pumps runs for awhile then shuts down and then starts back up in about half hour this is repeated numerous times. my pump is about two years old. my pressure is good
Reply
Dennis, how old is the timer that is connected to the pump? When the pump shuts off does it trip the breaker?
Reply
I need a start capacitor for century B2847
Reply
Could you supply us the MFD rating, Part # and volts from the capacitor? Or if you could post a photo of the capacitor showing the data printed on it that would be helpful. To supply this information or photos then click the reply link below.
Reply
iT SAY THAT THIS CAPACITOR LISTED IS THE RIGHT ONE FOR 1.5 HP HAYWARD PUMP BUT I PURCHASED ONE AND IT WONT CONTINUE TO RUN THE PUMP
Reply
Most motors have both a start capacitor and a run capacitor it sounds like you may have switched out your start capacitor when you run capacitor needs to be replaced.
Reply
I have a 2 horsepower to Hayward Super Pump I believe the start
Capacitor
went on. I can't find a part number for a replacement, do you know what it is? And is there a run capacitor in this type of pump also?
Reply
So in order to cross reference the correct capacitor we would need the motor model, part number or catalog number.
Reply
What would be the correct start capacitor for Sta-Rite 3/4 HP model C48J2PA105CI motor? This runs the pump for the pool water falls.
Reply
I switched my Hayward pump from 110 to 220VAC. Followed the instructions for the jumper settings. Pump runs fine, but I have had two starter capacitors, 61-193 MFD (BC-161), go out in just a few months. Should I switch to a higher voltage rating cap? Never had a cap fail when it was 110.
Reply
What is the current voltage on the capacitor that you have?
Reply
No, stay with the same rating on your capacitor. Unfortunately there is no way to determine why you have gone thru 2 lately. It should have nothing to do with the change in voltage as the mfg chose that specifically for the dual voltage motor. Your motor windings could be going bad/weak, it could be the new capacitors themselves.
Reply
I have a Hayward super pump 3/4 hp motor. Model Number C48J2N131B1. Is the 161-193MFD (BC-161) the correct start up capacitor.
Reply
I have a NGM capacitor 61B1D220124NNCA which is rated as 124-148 uF and 220 V. Do you have a replacement --- running at 220 volt. Motor turned freely after shaft seal replacement.
Reply
The replacement start capacitor is the 124-149 MFD (BC-124)
Reply
What type of capacitor should I use for a Hayward SPX2707Z2M 1-Horsepower 2-Speed ?
The pump model info & the specific motor used do not reference the capacitor required. We match it based on the microfarads listed on the original, so if yours listed the 161-193 mfd, then 35-125-1020 is correct.
Reply
What start capacitor would I need for Heyward super pump C48k2n143b1 1hp
Reply
Hello,This will be the correct capacitor you will need for your motor. http://www.inyopools.com/Products/07501352014027.htm
Reply
I need a start capacitor for a Hayward c48j2n131. It’s a 3/4hp, 115/230v set up currently for 115v. Is BC 161 the right capacitor?
Thanks.
Reply
I have a Hayward Super Pump C48L2N134B1 (SP1610Z1M) that is causing issues tripping the breaker and im looking to replace the capacitor for it. it only happens when it starts up. What would be the capacitor model number?
Reply
I am having a hard time finding the same capacitor as the one in my picture with the measurements of 1 3/4" wide and 3 5/16" long. Please Help and Thank you in advance!
Hi, I have a hayward pump that won't start; the capacitor is 61B1D110161NNMO. I measure about 77 microfarads so seems to be my problem. I have a Hayward 1 1/2 horsepower pump that was converted to 208v (not by me); this capacitor is rated @ 110v, so I'm wondering if I should be replacing this capacitor with another model. Of course, the pump had been running for quite some time without problem, so perhaps the capacitor @ 110v is not an issue?
Thanks!
Dale
Reply
Voltage is not an issue even if the pump is 240 the capacitor is only on one leg and that one leg is only 120.
Reply
would this capacitor replace hayward super pump II. 2 H.P.. Does it matter if it says 161-193 uF ,or, 161-193 MFD
Jerry, after reviewing your photos the correct replacement is indeed the Start Capacitor 161-193 MFD - BC-161
Reply
What is the difference between the USQ 1152 and my UST 1152? Mine is a 1 1/2 hp amp PH 1 code M. I also
need the o-rings and the ceramic water seal and white plastic collar that fits on the difusser, The number on my motor
is W3SP3010X15AZ hope you can help.Maybe you might sell a kit made for this pump with all the parts i need.Right now i am getting a buzzing sound when i turn it on.Sorry no photos.
Reply
Hi, Johnny. The motor mounting flange is the difference. Your model pump uses Super II Tune Up Kit - GOKIT2 or GOKIT2SALT.
Reply
I have a Haywood Super Pump with a Century c48k2n143b1. I see you recommend a BC-161 capacitor for this motor. My question is that the capacitor is labelled for 110-125V but my motor is configured for 230V. Would a different capacitor be needed for 230V operation?
Reply
super 2 model c48m2n111a3 dose c stand for century motors? i have changed the seal and after completion the motor blow fuses but if i rotate the shaft once. it work for hours till the next cycle and again i need to rotate and keeps working till next what part i need to solve this misery. no humms all quiet
Reply
Hi Isaac, most often this is due to a failing or failed capacitor. Here is a guide that we put together called "How to Test a Pool Pump Capacitor" that should help with that.
Reply
I Have a Hayward superpump 1 hp. 61B1D110161NNAO.Is this the right one??
Reply
Hi Kevin, could you send us a few photos of your motor? Please take a close up shot of the motor label. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I have a Hayward Super Pump 1 hp self priming 10 ft lift, 115/230 volts, my capacitor is an NGM 161uf, -0 +20% 110 AC, 60HZ 610807-002, Am I looking at the right capacitor?
Reply
Hello Marvin, yes this is the correct replacement capacitor for your capacitor part number 610807-002.
Reply
I have a 7-187400-20, Century Centurion, AO Smith, 3/4HP pump that just hums. When I turn the exposed end of the axle with my fingers it will start. It runs quiet. But it will not start by itself. Is this the Capacitor and which spec do I need? The motor is 230/115V, 6.5/13amps 3450RPM.
Reply
Hi Michael, most often this is due to the capacitor failing. The part number for the capacitor on your motor part number 187400 is 628318-307.
Reply
my pump is on a timer when power comes on pump motor hums for two seconds then shuts off it does it agan on third try motor goes on and runs with no problem i have a start capacitor is the problem with the capacitor
Reply
Hi Tom, most often, this is a sign of a failing start capacitor. Here is a guide that we put together called "How to Test a Pool Pump Capacitor" that should assist.
Reply
Hello INYO,
What start capacitor do I need for an USQ1152? Old capacitor info is 61B1D110189NNAO, 189-227 UF, LOT092194.
Thank you most kindly for you help.
Also I have a STS1152R...what capacitor do I need for that one also?
Reply
What capacitor is for Waterway 3420820 pump...ao smith century lasar BN51 motor?
Hi Greg, Your BN51 Motor will use this 15769903 Capacitor NOT the 5270-14 capacitor on this page. We do have the 15769903 Capacitor in stock ready to ship! We also put together this Video On How to Replace a Pool Pump Capacitor which you may find helpful when you tackle this project.
Reply
I have a AO SMith ST1152 pump motor and have been using the BC-161 start capacitor. It runs at 240 volts. recently the capacitors have been failing every 2-3 months. Any ideas what might be going on?
Reply
Hello Brian, please review our PSC Ep. 86: Why is my pool pump motor capacitor failing? And Related Article: How to Test a Pool Pump Capacitor.
Reply
I am of need of a start capacitor for my Hayward Superpump . I cannot find the capacitor with the same specs as the one I pulled from the back of the pump. I have provided a picture. What is the correct start capacitor for my pump?
Thanks
Ben
Hello Ben, yes the U.S. Seal Manufacturing Start Capacitor 161-193 MFD - BC-161 would be the correct unit.
Reply
i have a old 1hp dyna-glas motor that needs a new capacitor, i believe it is just a run capacitor, is this the right one?
Reply
Hi Geremia, could you send us a photo of your motor? Please take a close up shot of the motor label. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I replaced the shaft seal and when I placed everything back, motor just hummed! I think I need a new capacitor. Which one should I get? Thanks a million!
Hi Grace, Thanks for the photos! This 5270-14 capacitor is the correct replacement capacitor for the one shown in your photo. Humming is a sign that your capacitor needs to be replaced. We have put together this Video on How to Replace a Pool Pump Capacitor which you may find helpful when you tackle this project.
Reply
I have an older wmc at5200 motor can you tell me which capacitor I would need?
.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "U.S. Seal Manufacturing Start Capacitor for Pool and Spa Pump Motor, 161-193 MFD, 110 to 125 Volt - BC-161")
We will need for you to remove the capacitor from your motor and give us the specs off of the capacitor for us to suggest the proper replacement. If you could supply the MFD, VAC and Model # from the capacitor that would be helpful. Please click the reply link below to supply this information.
Reply
Hello! I'm looking for a start capacitor for a 1 hp sta-rite pump, 61B1D110161NNAO.
Do you carry it? If not, do you know where it can be found?
Hi, Yes this is the correct replacement capacitor for your 680171-002 capacitor shown in your photos.
Reply
I have a century C48L2N134C1 pump. Which capacitor do I need. Pump is humming when turned on but not tripping.
Thanks for your help.
Reply
Hello Brad. The U.S. Seal Manufacturing Start Capacitor, part number 5270-14, is the correct replacement for the Century Motors model UST1152, C48L2N134C1.
Reply
I have Jandy PHPM2.0 pool pump with AO Smith/Centurian motor O-193987-24. I am looking for START capacitor. Can you please help? I called several times and no one seems to know. Thx a million!
Hello. The replacement capacitor for the A. O. Smith motor 0-193987-24 is the U. S. Seal Manufacturing Run Capacitor (Permanent Split) 30 MFD (5VR0303) (244). RUN CAPACITOR, 30 MFD (5VR0303) (2444). Please reference your capacitor MFD (UF) and voltage ratings for accuracy. How To Find The Correct Capacitor For Your Pool Pump Motor
Reply
Looking for the starter capacitor for a UST 1102 Hayward Pool Pump 1H Motor Model C48K2N143C1C Volts 115/230 RPM 3450
FR56J H260 Type UAK Do not have the Microfarad Rating.
Thank you for your help.
SS
Reply
Hello Stephen. The U. S. Seal Start Capacitor BC-191 is the start capacitor for the Hayward Pool Pump Motor model UST1102.
Reply
Hello,
I have a Hayward/AO Smith super pump. Model# C48K2N143B1. SP-1607-Z1-M.
I’m pretty sure I swapped the last capacitor out of an older pump but wanted to confirm the correct capacitor for this motor.
Thanks
Hello Rob. the U. S. Seal Manufacturing Start Capacitor 5270-14 is the correct capacitor for the Century Motors model C48K2N143B1. Attached please find an exploded parts diagram for the Century Motors UST1102 (C48K2N143B1) for reference. Century / A.O Smith UST Series
Reply
Is the Start Capacitor that I am inquiring about (Start Capacitor 161-193 MFD - BC-161) the replacement part for the pictures sent? Or do you carry the replacement if this isn't the right one?
Thx Eric
Hi Eric, yes, the Start Capacitor 161-193 MFD - BC-161 will be a perfect replacement for the one shown in your photo.
Reply
I need a capacitor for this one and a half hp Heyward Super pump see picture attached can you recommend a capacitor that is correct. Thanks Jim
Hi James. Yes, the Start Capacitor 161-193 MFD - BC-161 will work on your Hayward Super Pump motor C48L2N134B1.
Reply
I have a Hayward Super Pump, 1 1/2 HP, AO Smith. Model #C48L2N134B1. Above is the replacement for the start Capacitor that popped up when I googled the specs and your web site came up with this part. Can you confirm this from the Info I just gave you plus the Pics I am sending? If this isn't the correct part can you tell me which is? Sent this yesterday, haven't gotten a response from you, and Chat isn't working?
Thx Eric
Sorry about the delay, Eric. Yes, this Start Capacitor 161-193 MFD - BC-161 will work on your Hayward Super Pump motor C48L2N134B1.
Reply
I have a 1 hp dyna glas pump and it has a bad capacitor, 161-193 MFD but the old one is marked 110 volt, but I am running it on 220V. Is your capacitor for 220V?
Reply
Hello John. The U. S. Seal Manufacturing Start Capacitor 161-193 MFD - BC-161 110 volt, part number 5270-14 is the correct replacement. The key to identifying the correct capacitor replacement is matching the voltage and microfarad specifications. Regardless of the voltage being supplied to the pump motor, the capacitor ratings should always match, old to new.
Reply
My pool pump has a start capacitor NGM 61B1D220124NNCA 124-148uf 220VAC. The case is 1 7/16" x 2 3/4". I can find the capacitor in the correct uf/voltage and the case is to big. What do you suggest?
Reply
Hi Erik, unfortunately, we do not have a capacitor that is a match to the info provided.
Reply
Capacitor number for hayward pump model C48K2N143B1
Reply
