Part # 5270-31
Manufacturer Code 6203
Dimensions 17x40x12 mm
Alternate Part #'s 10000353, 1011956-001, 203LL, 35-125-2600, 38113, 604005-001, 604005001, 6203, 6203-2NSE9, ALA605002, APC6203, NA-6203-LL, NA6203LL, RBL-6203-LL, USS-60-5026
Bearing, 203 (Single) - 62032RS
Motor Bearing, 6203, 17mm ID, 40mm OD
I am in the Bahamas and not near a supplier. I want to be ready for a bearing failure on my pool pump motor. It is a Century UST1152. What would I need if a bearing goes bad?
Reply
Hello Tom. Attached please find the Century UST1152 exploded parts diagram. The Pool Pump Motor Bearing, 1.5748" OD - 6203 (qty 2 required) is the appropriate power end and opposite power end bearings. Attached please find brief tutorials How To Replace the Bearings in a Pool Pump Motor - Part I How To Replace the Bearings in a Pool Pump Motor - Part II WRITTEN BY: Inyo Pools
Reply
Salut, de quels numéros de roulement aurais-je besoin pour ma Superpump Hawyard 1 1/2 HP ? Le numéro de modèle est le : C48L2N134B3
Reply
Bonjour, les roulements dont vous aurez besoin pour le moteur C48L2N134B3 seront deux des Pool Pump Motor Bearing, 1.5748" OD - 6203.
Reply
What bearing do I need for a Century 1-177450-03 and what other parts would I replace on a wfe-4 during this service. Thanks Robert
Reply
Hello, the bearing you will need will be the Pool Pump Motor Bearing, 1.5748" OD - 6203; this will be the bearing for both the service end and the opposite service end of the motor. You will want to separate the motor from the housing to replace the bearings, and every time you separate the motor from the housing, you will want to replace the shaft seal-- the shaft seal you want would be the Pump Shaft Seal, Heavy Duty PS-1000-style for Saltwater Pools - PS-3865. Other than the bearings and seal, that should be all that you need.
Reply
What are the bearing parts numbers to order for bearing replacements on Century UST1202 model number K48M2N110C2?
Thanks
Reply
Hi Yves, the UST1202 motor uses this Bearing, 204 Ntn 6204-ll (6204-2rs) on the rear side and this Bearing, 203 (Single) - 62032RS in the front (shaft end). Don't forget to get a new shaft seal or Tune-Up Kit to keep leaks from ruining your new bearings.
Reply
I am looking for the correct replacement bearing size for the following Century motor:
Century HSQ165
Motor Mod: C48AB46A01
HP: 1.65
SF: 1
Thank you!
Photo attached
I'm looking for the bearings for a Hayward 1.5 hp Super Pump motor, model C48L2N134B3
Reply
Hello Ed, This motor uses 2 of the 203 Pool Motor Bearings. I have also emailed you an estimate connected to your account with us if you need to place an order for them. They are in stock and ready to ship.
Reply
what is the correct bearings for centrury pool &spa motor, SP3220Z1BE, part# 7-196338-24, hp 2.0, serial # 35116J2ML050020337, thank you
Reply
Looking for the ball bearings or tune-up kit for an AC Smith - Century Pool & Spa motor - SP3207Z1M - 1 HP - Part# 7-F56AA11A04-04?
Hello Michael, so tune up kits are based on the model of the front pump housing wet end the motor is attached to. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that. Also PART # 5270-31 MANUFACTURER CODE 6203 Bearing, 203 (Single) - 62032RS is the correct bearings for this motor.
Reply
I need pump bearings for a A.O. Smith B2852 3/4 HP Motor. What would you recommend ?
Reply
Looking for the bearings for a Century 7-177893-24 BN24 motor V48Y SERIAL 07314J2
Reply
Hello Giuseppe. The Century Motors model 7-177893-24 requires a quantity of two (2) Bearing, 203 (Single) - 62032RS
Reply
Is this the 2004-2011 Polaris PB4-60 model? Can you please confirm if this is the correct bearing p/n and what tune-up kit?
Hello. The Bearing, 203 (Single) - 62032RS (qty 2 required) is the correct Drive End and Opposite Drive End bearing for the motor model 0-173840-23. Attached please find a brief tutorial How To Determine the Date Range of a Polaris PB4-60 Booster Pump From the attached photos, your motor frame is a N56CZ, proceed to tutorial step 3. There is no bundled tune-up kit for any of the Polaris Booster Pump models. The motor shaft seal and Bracket to Volute O-Ring are identified in the exploded parts diagram for each model.
Reply
I have a Pentair Dynamo pump with a Century AO Smith motor (Part # 7-177961-23 1 HP 115 VOLTS RPM 3450). What bearings do I need and seal kit?
Reply
Hello Luke. The Bearing, 203 (Single) - 62032RS is the correct bearing replacement for the Century Motor 7-177961-23. The Tune Up Kit Purex - Triton Dynamo/Dynamite Dynatron - GOKIT46 is compatible with the Pentair Dynamo Pool Pump. Attached please find the Pentair/ Pac Fab Dynamo exploded parts diagram for reference.
Reply
I have a Century Motor B128, Part # 0-164303-23. What bearings will I need for the bearing replacement?
Reply
Hi Mark, this Bearing, 203 (Single) - 62032RS is the outside bearing and the Bearing, 304 Ntn-6304-ll (6304) is the service end bearing.
Reply
Will these bearings fit this motor?
Hi Donald, yes, the Bearing, 203 - 62032RS is used in your B668 motor.
Reply
I'm looking for front and rear replacement bearings for an AO Smith / Century B977 1 1/2 hp 2 speed pool / spa motor
Reply
Hi Joe, The B977 motor uses one of the 203 and one of the 304 ball bearings. Take a look at our videos on How to Replace Pool Motor Bearings Video Part 1 and How to Replace Pool Motor Bearings Video Part 2 for some helpful tips.
Reply
What are the bearings for a Century motor model USQ1102?
Reply
Hi Chris, the bearings and other parts for your USQ1102 motor are located on this page. It uses two of these Bearing, 203 (Single) - 62032RS. If you need it, our guide on How To Replace the Bearings in a Pool Pump Motor will guide you through the process.
Reply
I need to replace bearings on my pool pump:
Century
Part: 7-196445-05
Cat: B2984
Frame: Y56Y
I think the 6203RS should be the bearings?
What seal kit do I need?
Thanks
Reply
Hello Ben. The Century Motors Bearing 203, quantity 2 (two), is the correct bearing for the Century Motors motor model B2984. A seal kit would be specific to the manufacturer/model of the pump and not the motor. Please provide manufacturer/model information and a recommendation can be made. If that information is no longer visible or accessible, please provide several wide-angle pictures of the pump inclusive of the intake and discharge ports to assist in identification. Bearing, 203 (Single)
Reply
Looking for the bearings for a Century 7-177451-03 1.5 HP motor Y56Y
Reply
Hello. The bearing required for the Century Motors motor 7-177451-03 is the Century Motors Bearing 203 (62032RS). A quantity of 2 (two) is required. Attached please find an exploded parts diagram for the Century Motors Motor model B2842 (7-177451-03) for reference. B2842
Reply
I have a Whisper flow 8 2 Hp has a Century 7-177452 -03 motor 56 Y
Would like to know know what bearings are needed and also the re-seal kit to complete the job..
Thanks,
John
Hello John. The Century Motors motor model 7-177452-03 requires 2 qty Century Motors Bearing, 203 (Single) - 62032RS. Bearing, 203 (Single) - 62032RS Attached please find an exploded parts diagram for the Century Motors model 7-177452-03 (B2843) B2843 The GOKIT32 would provide the parts (seals and O-rings) required to complete this project. GOKIT32 Attached please find an exploded parts diagram for the Pentair Whisperflo pump Series. Whisperflo
Reply
Do you have the p/n for a Polaris Booster Pump Bearing? Pump is about 20 yrs old.
Reply
Hello Chris. Motor Bearings are specific to the motor manufacturer/model and not the Pump. The age of the pump is also a determining factor. The "typical" Polaris Booster Pump Motor requires two (2) 6203RS Bearings. Bearing, 203 (Single) - 62032RS Confirmation can be made during the replacement process. Attached please find 2 tutorials on the topic of motor bearing replacement. How To Replace the Bearings in a Pool Pump Motor - Part I How To Replace the Bearings in a Pool Pump Motor - Part II
Reply
Are these the correct bearings for a Century Centurion B2843 on a PAC-FAB Challenger 2 HP pump?
Reply
Hi Neal, yes, both ends of your B2843 motor use the Bearing, 203 (Single) - 62032RS.
Reply
I have a two speed century B2983 pump motor that I believe the bearings are going out what is the part number for these bearings? Is it the 203 bearing?
Reply
Hello Joseph. According to the manufacturer, the Drive End Bearing is the Bearing 304 Bearing, 304 Ntn-6304-ll (6304), the Opposite Drive End Bearing is the Bearing 203 Bearing, 203 (Single) - 62032RS for the Century Motors Dual Speed Motor model B2983.
Reply
Hi,
I need new shaft bearings for my MagneTek motor, part #8-187098-02, type CXPM. It looks to me like the correct bearings would be 203 (Single) - 62032RS. Can you let me know if this is correct, or which ones I would need?
Thanks for your help
Reply
Hello John. The Century Motors Bearing 203 (Single) 62032RS, requires quantity 2, is the correct motor bearing replacement for the Century Magnetek Motor model 8-187098-02.
Reply
Hi
Where is a video showing how to replace my pool bearings?
Reply
Hello Joel. Attached please find 2 videos relevant to the topic of replacing pool pump motor bearings. How To Replace the Bearings in a Pool Pump Motor - Part I How To Replace the Bearings in a Pool Pump Motor - Part II
Reply
Need to know what size bearings for my AO Smith Century Pool Pump. Thank you.
The 62032RS Bearing are the correct size for the SE and OSE for the QC1102 motor.
Reply
Hello I have a Hayward power flow matrix Dual speed motor. Model number W3SP15932S I am looking for a set of Shaft bearings. I also need a seal kit if you carry them. Can you help? I'm going to aired images of the specifications
Hello Peter. The Century Motors Bearing 203 (Single), requires 2, is the bearing replacement for the motor model 7-193347-01. The GOKIT74 includes the parts necessary to complete this project. Tune Up Kit Hayward PowerFlo Matrix Pump - GOKIT74 Attached please find an exploded parts diagram for the Hayward PowerFlo Matrix Pump for your reference. Hayward PowerFlo Matrix Pump
Reply
What bearings do I need to order from you for my Century Centurion Model #: B855
Part #: 7-177897-22
Thank you
Reply
Good day, yes the Bearing 203 (Single) - 62032RS would be the correct replacement.
Reply
I have a Pentair 11/2 hp superflow Pump model 340039. Motor# 196239. Which bearings do I need for this motor?
Hello Tim. The Front and Rear Bearing is Century Motors Bearing 203 (62032RS). Bearing, 203 (Single) - 62032RS Attached please find an exploded parts diagram for the Century Motor B2854, 196239. Century 56Y Up Rate Single Speed Series B2852, B2853, B2854, B2859, B855, B2840
Reply
Will these fit my pump? My pump is not even a year old. Now it sounds like a jet about to take off. Pretty sure its the bearings.
Yes, your Pentair Superflo 340038 would use two of these 203 bearings.
Reply
Hi! My Hayward 1 hp Super pump mdl # MC48K2N14381 needs new bearings. What 6203 bearings do I need? It appears as though there are different 6203 bearings? Do I need to replace any other parts to complete this repair?
Hi Sal, Your motor will take two of these 6203 Pool Motor Bearings. I would also suggest this Hayward Super Pump Seal Kit. We have put together a couple of videos on How to Replace Pool Motor bearings which you may find helpful when you tackle this project. Video on How to Replace Motor Bearings - Part 1 and Video on How to Replace Motor Bearings - Part 2
Reply
looking for bearings for century usq1202 K48M2PA105C5
Reply
A USQ1202 would use one 203 bearing and one 204 bearing.
Reply
What front and rear bearings do I need for this K48L2N104 Motor?
The K48L2N104 (CT1102) motor would require one 6203 bearing and one 6304 bearing.
Reply
What front and rear bearings do I need for this SQ1202 motor?
Hello Jolyon. The replacement bearings for the Century Motors model are one each of the following: Bearing 5270-01 Bearing, 203 (Single) - 62032RS Bearing 5270-32 Bearing, 204 Ntn 6204-ll (6204-2rs)
Reply
Hi - My Hayward Super Pump (SP2615X20) 2 HP pump has been making a real loud grinding noise for the past couple of weeks. I only bought it 5 years ago and very disappointed that it already starting it give me issues. See attached pictures for reference of make & model. Motor is Century K48M2N111.
A) Is this the correct ball bearing replacement for my motor?
B) Can you tell me correct impeller for my Super Pump
C) Any other parts I should also replace as I do this job
Thanks!
Hi Harry, yes these are the correct bearings and you will need 2 of these. I would also suggest this Hayward Super Pump Seal Kit and this 2 HP Hayward Super Pump Impeller.
Reply
Which bearings do I need to replace the ones on my pump? (See attached).
Thanks!
Hi Kurt, Unfortunately, we do not have confirmation on the HSQ220 on which bearings are used. We believe it requires 1 6203 Bearing and 1 6204 Bearing. However, it could be 2 6203 Bearings. We would suggest purchasing 2 6203 bearings and 1 6204 Bearing as when you remove the old bearings you should be able to match the bearings up to see which you require, by going this route you can have an extra bearing on hand or return the unneeded extra bearing.
Reply
What motor bearings fit the ao smith c48j2n131b3 (hayward sp1605z1mbk)? Do I also need to buy any gaskets/seals if I replace the bearings?
Reply
Hello. Century Motor Bearing, 203 (single) is the replacement bearing for the AO Smith motor C48J2N131B3. Bearing replacement requires a quantity of two (2). It is recommended that the motor shaft seal, pump gaskets, and O-rings be replaced as a part of this rebuild. These items are specific to the manufacturer make/model of the pump itself. Please provide this information and/or pictures of the pump inclusive of the inlet and discharge plumbing and a recommendation for these replacement parts can be provided.
Reply
Hi I am looking for replacement bearings for a 2004 AO smith motor , 7-187331-20 3/4 horse. Thanks !
Reply
Your B852 Motor (7-187331-20) requires two 203 bearings.
Reply
Wanted to know a what bearing would go to this pump and gasket seals, thanks!
Hello Marcus, yes the Century Motors Bearing, 203 (Single) - 62032RS would be correct.Thank you for the information on your motor. We will also need the make and model of your pump. This information is typically listed on a label on the housing area, opposite the motor. Once we have this information, we can better answer your questions/concerns. Please let us know if you need help locating this information on your pump.
Reply
I'm not sure if this is the info you needed for the pump, it was on opposite side of motor housing, I could not find any other info anywhere, maybe if when I take it apart , but also, how many bearings would I need for my motor?
Hi Marcus, we actually need an image of the front pump wet end housing that this motor is bolted to in order to confirm the correct seal kit for you. Also, you need two of these bearings for your motor.
Reply
I'm currently in the process of replacing the bearings on my Centurion B2842. I've found the bearings but I don't see any of the shims that fit between the bearings and housing. They are shown on the exploded parts for my motor but no number is assigned to them and they aren't listed. Can you tell me where I can get the shims that I need? Thanks.
Reply
We do not offer the Thru-bolt for this motor, the part number is 16285667. You may need to contact Regal Beloit directly for a dealer that stocks them https://www.arcat.com/arcatcos/cos47/arc47651.html
Reply
I want to replace bearings on my pool pump motor. Its a ao Smith sq1152 1.5 hp. I know the front and rear are different sizes. I just don't remember what sizes.
Good day, yes the Bearing, 203 (Single) - 62032RS would be the same for both the front and rear.
Reply
I have the century B2840, ordering the the front and rear bearings to replace , what seals do i need to order?
Thanks,
Casey
Reply
For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Looking for motor Bearings and new shaft seal for our pool pump. Centurion B855 motor with PAC-FAB Challenger 2 HP pump. Would you tell me which ones I need? Thank You
Reply
Hi Dana, this is the rear bearing for this motor and the front bearing is part number 5270-32. There are two shaft seal options. The standard one for a chlorine swimming pool is part number 5250-104 and for a saltwater pool is part number 5250-210.
Reply
Hi do you have any information on the bearing itself? What kind of material are the balls made of, number of balls, etc?
Reply
Hello Gage, Bearing Material would be Steel, Radial Ball Bearing, Double Sealed, Cage Material would be Pressed Steel.
Reply
Looking to replace bearing on this motor. What are the correct ones and what else should I replace like the orings and shaft seal?
Yes, this would be the correct bearings for the front and rear of the motor and in order to cross-reference the correct seal kit for yu, w will need the model name or number of the front pump housing wet end that the motor attaches to.
Reply
Thank you for your reply. I have never changed bearings on a motor in my life. I'm thinking of attempting to do myself to save money from changing out the entire motor. If I do should I also replace any seals also? I'm a little handy and will be careful to turn of all power and discharge the capacitor as in your videos.
Hi Louis, We actually have two videos on how to replace bearings in your pool motor which you should find very helpful when you tackle this project. Please find the video here.. How to Replace Pool Motor Bearings Video Part 1 and How to Replace Pool Motor Bearings Video Part 2. Thank you very much for the photos of your pump those were quite helpful. You have a Jandy Stealth and you will require this Jandy Stealth Shaft Seal when replacing your bearings.
Reply
I have a Hayward Superpump (SP2615X202S) with a Century sp1615z2msc 2 hp pump. Are these the correct bearings? Thank you.
The 7-177108-01 (aka, B977) uses one of the 203 and one of the 304 ball bearings.
Reply
Hi!
I have an
AO Smith
Part: 7-196337-20
Is this the right bearing for this motor?
Thanks
Yes, the 7-196337-20 pool pump motor uses two of the 62032RS (10000353) bearing.
Reply
Does it fit the AO Smith 7-17780302? Of course it takes two opposing ones.
I looked though the previous questions but it is quite long, I did not see it
Reply
Hi Bill, this is the correct bearings for the front and rear of the motor part number 177803,
Reply
I can't seem to find this Model pump anywhere. Can you tell me which bearings will work on this pump?
Thank you, and thanks for a great website!
Hello Juan, yes the Bearing, 203 (Single) - 62032RS would be correct. For both the front and back bearings.
Reply
I have a century centurion a.o. pool pump motor part # 193686-02 need motor bearings? thanks kent
Reply
I have a century centurion a o smith motor part # 193686-02 Need 2 bearings thanks kent
Reply
Hi. I need bearings for my SplaPool pump motor: 1.5HP, 115V, 60Hz, Single Phase, 9.5Amp, 3450RPM
Model #72730 ; Motor Model RS4G24913L
Is the 6203 bearing correct for this pump? It would be greatly appreciated.
Thanks in advance.
Chris
Reply
Unfortunately, we do not have the listing for the bearings to this motor. You will need to remove the bearings and check to see if the manufacturer listed the part numbers on each bearing. Please see How To Replace the Bearings in a Pool Pump Motor - Part I http://www.inyopools.com/HowToPage/how-to-replace-the-bearings-in-a-pool-pump-motor.aspx
Reply
I have two AO Smith motors/Hayward motors: Model numbers are: C48L2N131A1 and C48K2N143B1. Will this bearing fit both motors? Thanks, conrad
Reply
Hi Conrad, yes this 6203 bearing is compatible with both of these Century motors.
Reply
Need replacement bearings (front and back) for Century (AO Smith) motor 7-173840-23 (3/4 HP). Think Century part number is 10000353.Bearing MAY also be referred to as # 6203. Application is Polaris Booster Pump (PB4-60).
Need to know if you have them and the manufacturer(s) (very important). Interested in high quality bearings. NOT low quality bearings! Please provide INYOPool part #s to avoid ordering wrong bearing. SEE PICS of motor and plate!
Thanks!
Jeff
Hi Jeff, these are the correct bearings for the front and back of the B625 motor and are manufactured by the same quality motor manufacturer.
Reply
B129 motor on a Hayward North Star what are the two bearings needed ?
Would you know the bearings size for the motor of a Hayward Super Pump 1.5HP model C48L2N134B3? The other number on the motor is SP1610Z1MBK.
Hi Jean-Pierre, these are the correct bearings for your motor model C48L2N134B3.
Reply
will this bearing fit my hayward NorthStar 2hp motor
Reply
Hello, if you can provide us with the motor model, part, or catalog number then we can confirm the bearings needed. That should be located on the motor label.
Reply
I need a gasket for my Red Jacket well pump with a 1/2 HP AO Smith motor model C48J2EC11
Unfortunately, we do not sell seals for well or irrigation pumps. You may want to try a local irrigation or well service company.
Reply
Hi, Will these bearings work for my Hayward SuperPump II #C48K2N143B3? I see a few references to the "143B1", not sure if this is the same...
Hi Russell, yes these are the correct bearings for the motor model C48K2N143B3.
Reply
What is the rear bearing replacement for A O Smith motor 7-187563-02? Do you stock this part? Thanks
John Bivona
bivonaj@gmail.com
Reply
We will need the CAT# off of the Century or AO Smith motor label to review for the bearings. The number 7-187563-02 is a part number that could come from other manufacturer motors and should not be used to cross-reference bearings as the manufacturers could use different bearings. We may not have all bearing numbers to provide and may need to remove them from the motor first to check the numbers on them. Please see How To Replace the Bearings in a Pool Pump Motor - Part I http://www.inyopools.com/HowToPage/how-to-replace-the-bearings-in-a-pool-pump-motor.aspx
Reply
I plan on ordering a B2841V1 motor but want to make sure I get the correct shaft seal and other new gaskets that my be required to install the motor to the pump.
Could you send us a few photos of your pump? Please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Per you request I am attaching photos of the pump installation. I have ordered and received the B841 motor and 5270-1 bearing but note in your parts breakdown that I did not see a shaft seal. In your how to video of changing the bearing and seal it shows a shaft seal. Since I have a leak in the pump to the motor I want to make sure I have or need a shaft seal that I don't seem to see depicted on the parts breakdown.
The Tune Up Kit Pentair/Purex Whisperflo - GOKIT32 or GOKIT32SALT is recommended for the Whisperflo Pump. You will need a thin layer of Clear Silicone RTV applied to the Seal Plate for the metal backing of the shaft seal to bond with the plastic, without the sealant it will leak.
Reply
I have an old 2HP AO Smith SP1620-Z-1-BNSC. Which replacement bearings should I buy?
Reply
Your motor will require one of this 6203 bearing as well as this one of this 6304 Bearing
Reply
I have a Pentair 1/2 hp motor (motor# 177449) that needs new bearings. I understand that your 62032RS will replace 6203DW, is this correct? Also I would like to replace the motor shaft bearing shields. Could you tell me which shields to use?
Yes, the 6203DW is replaced by the Bearing, 203 (Single) - 62032RS Unfortunately, we do not have the Pentair Motor bearing list, you will need to contact them directly at 1.800.831.7133 for them as they private label their motors. Or you can use How To Replace the Bearings in a Pool Pump Motor - Part I http://www.inyopools.com/HowToPage/how-to-replace-the-bearings-in-a-pool-pump-motor.aspx to remove them then order based on the number you find on each front and rear bearing.
Reply
Hi, appreciate this site and it's resources.
I have an AO Smith 1HP motor that is needing some care.
SP-1607-Z1-M
Can I get the part #s for the bearings, end plate, seals?
Thank you very much.
Hi Alani, Thank you for the kind words! This 203 be the proper bearing for your motor. Please click here for all of the SP1607Z1M Motor Parts and click here to view all of the Hayward Super Pump Parts
Reply
I have a E.O. SMITH/CENTURY Hayward Super 2 pump motor #B2979 and would like to know the bearing P/N. the pump is SP3020X252 and the other number on the motor is 7-K56AB47A01-05.
I have a Hayward Northstar 2.5 hp pump. Part Number is 7-187939-03. What bearings does it use? Can you provide a complete rebuild kit, including diffuser, impeller, seals, bearings, and other parts that you would recommend to be replaced?
Does my Pentair pump with motor# 177451 use the same 203 bearings on both ends?
Pump model number is SF-N1-2AE/348025
I assume this is an A.O. Smith motor from info on the label?
Thanks
Reply
Will these bearings work on my Century motor SPX151515Z1E
I reached out to Hayward, but they just gave me the part number for the motor. Century hasn't responded to me yet.
Pump is a Hayward Power-Flo Matrix
6203 is correct but we are not able to determine if it is the 17mm I.D. bearing mfg # RBL-6203-LL or a 15.9 mm I.D. mfg # NA-6203-10-LL.
Reply
Century motor SQ1152, HP 1.5, Volts 230. Need all bearings and seals can you give me the part numbers please.
Reply
Do you know which bearings fit this unit?
I am looking for part numbers for the bearings, seals, and starting capacitor for an AO Smith B748/B2748 motor. Can you assist and also point me to a parts breakout for this?
Reply
We added a picture of the run capacitor (RD-35-370 ) 35-125-1135, the seals are based on the pump wet end & not the motor & we do not have a breakdown of the correct bearings for the motor. Generally, the techs in the field will pull the bearings & tell us what the size is.
It seems that nobody has bearing information for this particular pump. I contacted Century/Regal Beloit, and they were able to provide the information. The two bearings the B748 / B2748 motor uses are the double sealed 6203 and 6304. From what I gather, they are generally listed as 6203-2RS and 6304-2RS.
Reply
I need to know what bearings I need for 2 pumps
AOS 0-187624-01
AOS 0-187563-02
If they are different numbers can you tell me what part numbers i need for the front and rear bearings of each. thank you for the help.
Reply
Hello, Unfortunately, we would not carry those bearing on our website.
Reply
Sorry but we do not have a cross reference for motor bearings. The techs i the field pull the bearings & tell us what they have.
Reply
Is this the right bearing for my motor?
Century UST1102 1 HP
Motor Mod C48K2N143C1C
Reply
Yes, the Bearing, 203 (Single) - 62032RS is correct for the UST1102 it uses the same bearing for both the shaft and opposite shaft end of the motor. How To Replace the Bearings in a Pool Pump Motor - Part I
Reply
Hi, I'd like to confirm that this is the correct bearing for my pump. I have a AOS Centurion motor 168453 - Y56Y (picture attached). I think I need 2? Thanks in advance!
I am looking to replace the bearing for my pool pump model sp3215z1be, see attached picture. The pump works but is making very loud noise (like rust grinding noise). I am trying to avoid replacing the motor as nothing seems to be wrong, can you advise what is the bearing part number and any related "seals" o-ring that i might need for this job. Thanks
Sorry but the motor mfg does not list the bearings required. We are supplied the bearing information from the field techs to match.
Reply
I have a Century Pool and Spa motor 1081 Pool Pump Duty.
CAT B625
Part 0-173840-23
I need to replace the bearings and seal.
What should I get?
Thank you.
Hi, Chris. These 62032RS are the correct size for your motor. As for the seals, I will need to know which one of these model Booster Pumps you have.
Reply
Hello, I have a Century K48M2N110 which bearings need to be replaced (see picture here-attached). What are the right replacement bearings to order please? And what seal kit?
Thanks in advance.
Hi, Frank. The motor you have use (1) 6203-2RS and (1) 6204-2RS bearings. As for the seal kit, I will need to know the housing model or name that this motor is mount to.
Reply
Thanks Lennox for your quick feedback. The pump model is a Hayward SP3020
Reply
Frank, You will need the Hayward Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT.
Reply
I have an AO Smith (Century now I hear) C48L2PA105C4 and it sounds like the bearings are going. Can you give me the right part number so i can order?
Thanks!
Reply
I have an AO Smith motor .#187694 for my spa. What bearings do I need for this motor, and do you recommend anything else to be replaced at this time?
Reply
We are sorry but we are not able to confirm the correct bearing for your motor as the mfg does don publish a complete breakdown & the reason for that is that they use can/will change different manufacturers of seals o the same motor. We require techs in the field to pull the bearing & provide us the information on the bearing to match. Bearings also require a measurement as you can have as an example a 6203 bearing with a 40mm O.D. but you have an option of 17mm or 15.9mm I.D.
Reply
I have a AO Smith B129 pump that needs bearing replacement. What would the part number be? Also the seal kit while I have it apart.
Thanks.
What bearings should I use? Thanks.
Hello, These would be the bearings you will need, http://www.inyopools.com/Products/07501352012915.htmhttp://www.inyopools.com/SearchResults.aspx?KeyWords=10000353
Reply
Sorry but the motor mfg does not list the bearings as a replacement item on their motors. Techs in the field have to pull the bearings & then give us the information to match.
Reply
I am trying to identify which bearings I need to replace in my Hayward pump. I included a picture with the information on the pump. My pool does have a salt water generator. Thanks for any help!
Hello - your UST1152 (C48L2N134B1) uses two 203 motor bearings.
Reply
Will this part fit motor USN1252 for both the front and rear bearings? Or are does it require two different bearings?
Will this fit my motor?
Yes, the Hayward SPX1510Z1XE motor uses two, 203 motor bearings.
Reply
I have a Berkeley 2 HP Pump (Model 839524) with an AO Smith Motor number C48M2EC11C3. Which bearings do I need?
Thanks!
Reply
Hello - the C48M2EC11C3 motor uses, one 604005-001 and one, 100025-002 bearing.
Reply
Trying to figure out the bearings for my friends pump motor. Also a seal set since I'll be breaking it down
Thnx
We do not have a breakdown from the motor mfg to tell us the correct bearing. You will need to remove the bearings to I.D. There are several o-rings you will want to consider as well as the shaft seal replacement. See key #'s 3 - 90-423-5366, # 6 - 90-423-5338 x 2, # 16 - 90-423-5375, & the shaft seal key # 11 - 35-295-1168 (recommended)
Can you provide the part numbers for the motor bearings and pump seal for the Hayward pump model shown on the attached photo?
Hello - the SP1607Z2MSC uses two of the 203 motor bearings. The seals are matched to a pump housing instead of the motor. What is the model number of the pump housing this motor is bolting to?
Reply
Need bearings for Hayward SP1510Z1XBC. According to my research, they specify two different bearings. A Light Contact on the lead end and a full contact on the opposite end. I dont know what that means. Do you have these>
Reply
Hello, Unfortunately, we would not carry those bearings on our website. We recommend contacting the manufacturer with that question with that. You can reach them at 908-351-5400
Reply
I need bearings for a hayward 1hp powerflow lx ao smith part 7 193390-20 also need bearing puller and any seals. Pump is screaming right now. Neighbors not happy.
Thanks
Reply
Hello - the 7-193390-20 (1 HP Thru-Bolt 48Y Motor - BN25V1) requires two of the 203 bearings.
Reply
I have an A.O.Smith Cat 668 booster pump. Trying to determine bearing replacement. I think it is either 62032rs or 6203-625. Per motor schematics, shaft size is .625 inches. So I am thinking it is 6203-625.
Reply
I have a motor with an AO Smith motor with a motor number 177474 and a pump number sf-n1-a1/340038. What bearing kit and seal kit would need for this motor? And can you also recommend a pump rebuild kit for that pump model? Thank you
Hello - the 177474 Pentair SuperFlo motor uses two of the 203 bearings and requires the GOKIT78.
Reply
do these bearings fit 7-187098-02 motor?
Reply
Hello - The B2236 - 5 HP Thru-Bolt 56Y Dual Speed 230V motor uses 2 of the A.O. Smith Bearing, 203 (62032rs)
Reply
Is the Manufacturer Code 6203 some sort of generic manufacturing code used by multiple bearing manufacturers? I've seen it in DC motors. (I'm having trouble keeping bearings (SKF) in an Ironhorse DC motor). Who makes YOUR 6203 bearings?
Reply
Hi, Milo. The number on the bearing 6203 is the bearing size or style. These bearings are manufactured by US Seal.
Reply
hi, pleace need bearin fom C48H2EC23, AO Smith, Electric Motor
is 6203 2RS two pcs?
Reply
Hi Pablo, This 62032RS Bearing is the proper bearing for your C48H2EC23 motor this is for one bearing and you will require 2 bearings for your motor.
Reply
do you carry replacement bearings for a Polaris booster motor Model PB-4 152-2? If not, can you suggest someone that might? Thank you!
Reply
Hi, Phil. You will need to provide us with the motor Part or CAT number in order for us to locate the bearings.
Reply
Looks like the Century/AO smith ECM16CU motor requires different bearings: 6203DG and 6203DW bearings. Will this work for one of them? What about the other bearing?
Reply
This bearing is not compatible.
Reply
Ok thanks. Do you offer bearings for this motor? Can you point me to them?
Reply
Hi William, We don't carry the bearings on the variable motors, we put together a Video on Can I Replace my Variable Speed Pool Pump Motor which explains why we don't carry these bearings.
Reply
Is this the correct bearing for a Pentair Whisperflow 1/2 HP engine: Pulb Model No WFE-2 and motor # 196232?
Reply
Hello, Unfortunately, we do not have the break down for that specific motor. We recommend contacting the manufacturer on that question, you can reach them at 937-667-2431.
Reply
I have a model c48k2n143 1 hp ao smith serial number 8k93 motor that I need to know what bearings are used. Thanks for your help..
Reply
Hi. These are the correct size bearings used with that model motor.
Reply
i have a Century pump SP1510Z1XBC part # Q-187872-21, what bearings do I need?
Reply
Hi Steve, Yes this is the bearing for your Century Motor SP1510Z1XBC part # Q-187872-21, two are required. We put together 2 videos on how to replace pool motor bearings which you may find helpful. Video on How to Replace Pool Motor Bearings Part 1 and Video on How to Replace Pool Motor Bearings Part 2
Reply
What bearing do I need for a centurion Pac-fab model 168454-25
Reply
Hello, Unfortunately, we do not have that information on that specific motor. We recommend contacting the manufacturer on that question. You can reach them at 937-667-2431
Reply
Need bearings for model number SP-15-1N11CC Insulated wet end pump
Reply
Hello, Unfortunately, nothing came up with the part number SP-15-1N11CC on my end. Can you please provide a picture of the motor label?
Reply
I have a AO Smith variable speed motor A.O. Smith (STS1152R - 56J - C Flange) that I used as a replacement for my Hayward Super Pump. The bearings are making a loud noise. Is this the right bearing? Thanks.
Reply
Due to the liability surrounding replacing motor bearings and other internal parts, the manufacturers do not give us the information to reference parts within these motors. For that reason you will need to call them for this information; AO Smith can be reached by calling 866-877-5216. We apologize for the inconvenience.
Reply
I need to replace the bearings in my pool motor. I was wondering what would be the correct replacement bearing for a SQ1152 motor? I need help. Thank you, Joe
Reply
what bearings do I need for the Century C48L2N134B1 AO Smith 1.5 hp motor
Reply
Hello, This would be the correct bearing for that motor. http://www.inyopools.com/Products/07501352012909.htm
Reply
Hi, would the 203 work as motor bearing replacement for the motor in the picture. That’s the only readable tag it has left.
Thanks in advance
Hi, MaxRo. These are the correct size replacement bearings. You will need (2).
Reply
Attached photo. Can you tell me which bearing I need for this motor.
These will be the correct bearings you will need, http://www2.inyopools.com/Products/07501352012909.htm
Reply
Can you tell me if this is the correct bearing for my motor? Thanks!
Tim
Unfortunately, we would not carry the bearings to this motor. We recommend contacting the manufacturer on that question, you can reach them at 1-800-831-7133
Reply
What bearings do I need for a Centurion SE pool pump motor 186467? It's 1.0 HP and 1.25 SF. I assume this is a Century motor? It's in an Ultra Flow pump made by American Products but also has Anthony Pools on the sticker.
Thanks.
Reply
Hi, Gary. These 62032RS bearing are the correct size for P/N 186467.
Reply
Hi,
I have an AO Smith motor on my above ground pool pump, CAT BN25 Part 177894 I need to replace the bearings in it. Can you tell me what bearings and seal to buy?
Reply
Hi, John. This is the correct size bearings for the CAT BN25 Part 177894 motor. As for the seals, I will need to know the pump housing model or name.
Reply
I am changing the motor bearings in my Hayward 2hp pool pump on the old bearing it says6203DW NSK where can I buy bearings? need ASAP
Reply
Hello, Can you please take a picture of the motor label? Or let me know of the part number on the motor portion? I will need this information in order find the correct bearing replacement for you.
Reply
Hi, What is the bearing part number for a Pentair 7-168454-25?
Reply
Hello, Unfortunately, we do have the parts break down for that motor. We recommend contacting the manufacturer on that question. You can reach them at 937-667-2431.
Reply
Are these the correct bearings for a AO Smith/Century UST1072 Motor Model C48J2N131C1C ?
Reply
Yes, this would be the correct bearings. You would need one for the front, and one for the rear of the motor.
Reply
Will this fit a century laser pool/spa motor 1081/1563 Part 7-184834-02. if so where can I find the other bearing and the seals?
Reply
Hi. Unfortunately, the only way we'll be able to confirm the bearing size is to get the number of them.
Reply
Hi,
I'm looking for bearings for an A.O. Smith 0-173840-23. Any help identifying the correct bearings would be appreciated!
Thanks!
Need Front and Rear bearings for a GE 2HP 56Z motor. I can see 6203Z on on the rear bearing but can't see any numbers on the front bearing. It is a "GE Commercial motor" and says "778 Jet Pump Motor" on the label. The model number is: 5KC48PN2145BX.
Thanks.
Reply
Hi, Ken. We will also need the ID and OD of the bearing since 6203Z is not cross referencing to any bearings we have.
Reply
So many numbers so confusing! Mine is C48K2N143B3 Hayward Superpump-II(two). Which bearings and shaft seal (saltwater) ?
Reply
Hello, You will need two of these bearings,http://www.inyopools.com/Products/07501352012909.htmThis will be the seal kit you will need for your super 2 pump for salt water pools,http://www.inyopools.com/Products/00100017069792.htm
Reply
Could you please tell me which bearings will fit my pump. Thank you!
Hi, Dallas. The OSE Bearing is 604005-001 and the SE Bearing is 100025-002.
Reply
Thank you!
Reply
Hi, I have Century Pool & Spa Pump with CAT B625 and Serial 12511CH and 3/4 hp for Polaris Vacuum booster. What type and how many bearing I need? Thanks
Reply
Hi Shah, you will need two of the 5270-31 bearings.
Reply
I have a Hayward Booster pump 6060 with an A. O. Smith motor C48D62A04 3/4 Hp. I need to replace the bearings and would like new Seals for the pump (Go Kit). Do you have what i need? Model numbers please? Is there anything else in there I need to consider changing while i have it apart
Thanks?
Reply
Hello, Can you please take a picture of the motor label on the booster pump?
Reply
I am looking for bearings for a century motor part no. 193994, can you identify?
Reply
Hello, You will need two of these, http://www.inyopools.com/Products/07501352012909.htm
Reply
I need bearings and seal kit for a Century B855 with Challenger High Head pump. Can you give the part numbers? Thanks!
Reply
Can you tell me if the 203 bearing will fit the pump represented by the attached pictures?
Thanks,
Bret Wiscomb
Hello, Unfortunately, we do not carry those bearings for above ground pool pumps.
Reply
I require motor bearings for a Pentair Sta-Rite PHK2RAY6F-103L pump with a AO Smith 177144 motor (1.5 HP, 230 V, Single phase, 2 speed motor). Could you tell me what bearings I require??
Reply
What bearings and seal kit do i need for this pb4-60. Thanks
Hi, Jeremy. These 6203RS bearing are the correct replacement for the motor in the picture. The seal kit will be based on the style or age of the pump. The Polaris Booster Pump Tune Up Kit - GOKIT71 will be used on model manufactured prior to 2011.
Reply
is this the correct bearing for my century C48L2N134B1, and are both front and rear the same?
Can't seem to confirm the correct bearings and shaft seal for a Century B2844 Part 0-196358-07 Frame Y56Y. I think the bearings are 203 and the shaft seal 200, but not completely positive. Can you confirm?
Reply
I have an A. O. Smith pump model B625 (Polaris booster pump). I need the front and rear bearings. Attached are the photos.They are NSK 418 2203DW
Hi, David. These 6203 are a suitable replacement for the B625 motor and will also replace the 6203DW bearings.
Reply
I have a century 3215z1be. Pic has the remaining details. And do i need one or two bearings, and any accompanying parts
Thanks!
You will require one 6203 Bearing and one 6204 Bearing for your Hayward Tristar Motor
Reply
Can you please tell me the bearings and seal part numbers, see attached photo. Thanks!
Hi Louie, For your motor, you will require one of this 203 bearing as well as one of the 6304 Bearing. We have a Video on How to Replace a Pool Motor Bearing which you should find helpful when you tackle this project.
Reply
I have a century 7-f56aa13a04-25 motor that needs new bearings. Do you have the replacement parts?
Nameplate picture attached for reference.
Hi Chris, You will require a quantity 2 of this 203 bearing as the proper replacement bearings for your motor. We do have a Video on How to Replace Pool Motor Bearings which you may find helpful when you tackle this job.
Reply
I am looking for the bearings for a pool pump motor AE100FHL. It's for a Sta-Rite Max-E-Glas Ii-Dura-Glas Ii Full-Rated Pump Parts-01 - P4E6F-188L 5 -152L 1-1/2hp
Part No: AE100FHL
Reply
I have a Hayward II super pump, 1.5hp, 2-speed, model SP3010x152az. I saw your video on replacing bearings, I can do that. I also saw your video that recommended not replacing the bearings yourself on variable speed motors. Does the 2-speed motor present the same problems as the variable speed motor when it comes to replacing the bearings for the DIYer? If I do replace the entire motor which model do I need, label is hard to read, AO Smith, probably SP1610-z-2-MBK (C or 0). Thanks
Reply
Hi, Richard M. Replacing the bearings on a dual speed motor is not as difficult as on a variable speed. The STS1102RV1 will be the replacement motor for model SP3010X152AZ.
Reply
I have an Hayward Super Pump (A.O Smith), model C48L2N134A4, 1,5 HP, SP-1610-Z1-MH. I have a salt system. The pump is very noisy. Do i need change the bearings? Can you tell me what i need to change and the parts number. Do you ship in to Canada? Thx
Reply
Hi, Sylvain. A loud motor usually is tied to bad bearings. These are the correct size bearing for your model motor. We can ship these bearing or the complete motor to Canada.
Reply
I have Polaris PB4-60 booster pump searial BZ07-02 part 7-173840-23 . says 1081 pool pump duty. This is older pump came with house, built about 1995. Would this bearing fit it?
Reply
Hi, Zee. Yes, these 6203RS bearings with fit your motor.
Reply
I want to repalce bearings for a SP-1610-Z1-MBK, could you tell me which bearings do I need and the other parts like seals etc? Do you ship to Canada? Thanks
Reply
I have a Century Centurion pool pump CAT B2853, PART 0-F56AA37A01-04, TYPE CX, FRAME P56Y, HP 1.0, what bearings will fit this motor? Thanks.
Reply
Looking for bearing number for Century stock# HSQ1152. SP3215Z1BE. Motor 7-196337-20. Pump seal number for Model SP3215EE.
Reply
I have a pentair 1 hp pump. A bad bearing NTN 6203 LH that went bad after a year. What is the replacement?
Reply
Hi, Derek. This 6203RS Bearing can be used as a replacement, you will just need to confirm the OD and ID.
Reply
I have a century 1081 pool and spa motor. Serial # BY04-28, Cat# B625, part 7-173840-23. What bearings and seal kit do I need?
Reply
This motor needs two bearing part number 5270-31 and for the seals, you will need to know the pump housing model name or number that the motor bolts to. If you do not know that you can email images of that to upload@inyopools.com so we can assist in confirming.
Reply
i have a (Hayward / A.O Smith) motor- sp1620-z-1-bns, it has started to make a squealing sound. I suspect I need new bearings
do you have any idea of which pair I need.
i think 6204 for the front and 6203 for the rear, but I am not sure, can you help me figure it out.
Reply
need bearings for a AO Smith EPC Model # SF-N1-1A Part # 340038 Motor# 196238 Thanks
Reply
Hi, Mike. These 6203RS bearings are the correct size for the motor you have. You will also need the SuperFlo Tune Up Kit - GOKIT78.
Reply
Hi i have a Pentair Dynamo 1hp pool pump part number 340197 need to know the size bearings it has and the seals
Reply
Loud squeal from pump / motor a Hayward super pump 3/4 hp serial # looks like C48J2N131 {label hard to read} on motor, pump you can't read at all. How would I go about finding the right bearings & seal kit? Thank You
Reply
Hi, Mike. These 62032RS bearings are the correct size, you will need two. You will also need the Hayward Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
I have a Pentair SuperFlo 1.5Hp that will hum - growl thee seems to be excessive play on the shaft. I suspect that the motor bearing are bad. What size bearings does the motor require
Reply
Hi, Joe. In order to locate the correct bearing, I will need to know the motor Part number.
Reply
I have a Magnetek Century 7-184843-03, the 6203 for the pump side fits fine but the 6304 is way to big. The original bearing if you call it that was destroyed so I can’t tell what it is.
Reply
Hi, John. You will need another 6203 bearing.
Reply
What size bearings do I need for an AO Smith K56N2N103, SER# 2E00?
Reply
Hi, Marina. These 6203RS will fit the K56N2N103 motor. You will need two, one for the shaft end and opposite shaft end.
Reply
I've got a couple of AO Smith K48M2A4 pump motors that need new bearings, I can see the numbers on one end calls for 6203 bearings, want to verify the same bearings on the pump end of the motor. Also need a couple of housing through bolts for same motor.
Reply
Hi, Shep. To confirm if these are the correct size, you will need to provide or verify the ID and OD.
Reply
i have a Century LASAR Pool/Spa Motor 1081/1563 Pump Duty manufactured by AO Smith for a Waterway wet end. motor info is as follows ...
Cat: BN37 Part # 7 -77783 -03 Frame R48Y any idea what bearings I would need to procure to perform a motor rebuild?
Reply
Hi, Ed. This 6203RS Bearing will fit the BN37 / Part # 7-177783-03.
Reply
I have a 1081 A.O.Smith pool motor 1 HP that need the bearings changed, what size bearings do I need?
Reply
Hi, Pam. You will need to provide the PART, MOD or CAT # of your motor in order for us to locate the correct bearings.
Reply
Which bearings will work in a Hayward Northstar A.O. Smith SP1615-Z-1-MNS, part # 7-187582-02? It has these specs 2HP, frame Y56J, Type CX, SF 1.20.
Thank you!
Reply
Will these bearings fit a AO Smith 7-177653-03 motor from a Hayward Super Pump SP2610x152S
Reply
Hi, Paul. It's possible, however, OEM motors are designed a little different. To confirm you will have to get the number from directly off of the bearings.
Reply
Regarding my question a few minutes ago, the number on the motor is SP1615Z2MSC. SERIAL # is 327093M
Reply
Hi Gus, Yes this would be the proper replacement bearing for your SP1615Z2MSC motor. We do have these two Bearing Videos which should help you out when you tackle this project. Video #1 How to Replace Pool Motor Bearings and Video #2 How to Replace Pool Motor Bearings.
Reply
are these the same as the 6203DW bearings like in yalls bearing replacement video? I need 2 6203DW bearing and want to be sure these will fit, and if not then which ones i need. thank you
Reply
Hi, JPowell. These can be used as a replacement, you'll just need to confirm the dimension. These are 17mm ID, 40mm OD.
Reply
Are these the correct bearings for a Hayward pump model# SP2607X10A, Hayward motor model# SP-1607-Z1-MBK, A.O. Smith motor model# C48K2N143B3? If not, which ones do I need? Thanks
Reply
Yes, this is the correct motor bearing. You would need two of them.
Reply
What bearing(s) (part Number) do I need for an AO Smith QC1102 pump motor and how many?
Reply
Hi, David. These 6203RS Bearings are the correct size for the QC1102. You will need two, one for the front and rear.
Reply
need motor bearings for Hayward super pump 1.5 hp model c48ln2134b1, and pump seal rebuild kit for same model sp2610x15
Reply
Hi, Steve. If you have the OEM Hayward motor, those use different bearings from the aftermarket Century UST1152 motor. The Century UST1152 aftermarket motor uses the 203 Bearing - 62032RS. You will also need to get the Hayward Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
I need new bearings for AO Smith motor 193994 (aka 7-193994-06), also is their a kit that goes with this?
Reply
HI, Lou. These bearing will fit the motor Part # 7-193994-06. I will need the model of the pump housing in order to locate the kit.
Reply
what bearings and seal kit do I need to rebuild a hayward super pump 1.5 hp SPX1610Z1M
Reply
You would need two of the bearing part number 5270-31, the seal kit for a saltwater pool is the GOKIT3SALT and the seal kit for the standard chlorine pool is the GOKIT3.
Reply
I need a set (2) of new bearings for my Hayward 1 HP Superpump Century MODEL C48K2N143B1 SER 10213J2. What part number of bearing should I request?
Reply
Good day, you will need two of the Bearing, 203 (62032rs) for that motor.
Reply
I have a AO SMITH centuriun 3 HP # 7-168888-07 is this the right bearing for me and do I need 2
Reply
I have a Hayward super pump II sp-1610-z1-be. It also says A.O. Smith model k48L2N104 I have a pic of the info tag but unable to post it. I need bearing part numbers and availability please
Reply
The A.O. Smith Model k48L2N104 will use two of the 1011956-001 - Bearing, 203 (62032rs) (Single) .
Reply
I need to replacement pool motor S?N CB03-15 HP 1.5 Part# 7-193233-02 self priming motor by A.O. Smith co. Hayward Super 2 Pump 3450RPM SP1615-Z-1-BNSC Use for pool water fall.
Thanks
Reply
With Motor AO Smith - Model K48L2N104 Serial# 01510FM - 1 hp that is connected to my Pool Pump "Hayward Model# S1000 Serial # 21110004050556006 if important.
Looking for the correct bearing. Is it a 6023, 6204 or 6304?
Thank you in advance,
Scott
Reply
I need to replace the bearings on my A.O. Smith STS1072RV1 motor (model number K48A73A01). Can you tell me which bearings I need?
Reply
Hello, this motor has been discontinued therefore I would be unable to find the proper parts for you. However, the replacement for this is STS1102.
Reply
I think these 5270-31 bearing may be correct for my motor. 8-177457-02. The century motor is on a Pentair Wisperflo 2.5 hp WFDS-30.
Thanks.
Reply
Hello I have a US Motors 1081 Pool motor Model c55cxkmc-5013 which bearings and seals do I need to purchase to replace front and back bearings.
Thanks
Reply
Hi, Ray. That model motor uses the 6203 Bearing on both ends.
Reply
Can you tell me what bearings I need for the Century A.O Smith motor reference as category USN1152, part #7-193685-02 Motor. Thank you
Reply
Hi, Dan. The USN1152 Motor uses (1) 304 Bearing (SE) and (1) 203 Bearing (OSE).
Reply
I have a Centurion 1081 uprate B2853 P56Y motor the part number on bearing is 6203DW (single light contact seal) would you have a bearing for this?
Reply
need replacement bearing for my ao smith motor model # c48k2n143b1
Reply
Hi, Ronald. These 203 Bearing are the correct size for the Century/A.O. Smith C48K2N143B1 aftermarket replacement motor. If you have an OEM motor with mod # C48K2N143B1 listed, these bearings will not fit.
Reply
what bearings do I need for B748 (7-186016-20)?
thank you
Reply
Hi, Lino. The Century B748 motor uses (1) 203 Bearing OSE and (1) 304 Bearing SE.
Reply
What bearings do I need for a Century Lasar BN50, Part #7-177803-02 1 1/2 hp pump motor.
Reply
Hi, Ryan. The BN50 Motor, Part #7-177803-02 uses the 203 Single Sealed Bearing (10000379) which we do not carry.
Reply
Can you please tell me the front shaft bearing needed for a century B854.....OF56AA40A01-24
Reply
Hi, Michael. The B854 Motor uses this 203 Bearing - 62032RS on both ends.
Reply
Can you tell me which bearings I need for my Century pool pump motor? The motor is cat B2840 P/N 0-F56AA42A01-20 Type CX Frame 56Y HP 2.5 SF1.04 PH 1 RPM 3450. I need both bearings. Thanks,
Steve
Reply
Hi, Steve. The B2840 motor uses the 304 Bearing - 10000445 (SE) and the 203 Bearing - 10000353 (OSE).
Reply
I have a Hayward Energy Flo RS self priming pump 1.5 HP motor serial 24814J2. It is making an awful noise. Purchased in 2014 according to Hayward it is a private label can you tell me the bearings I would need to replace. I read the comments and some needed 2 sets front and rear. How do you know if there are two sets needed. I cannot seem to find any schematics on this motor and I searched google.
you can respond to my e-mail address. would I be better off just buying another motor
Reply
Hi, Pam. Unfortunately, we're unable to locate the replacement bearing for the Hayward Energy Flo RS Pump.
Reply
I have a PB4 Polaris pump using an AO Smith 3/4 hp motor Will these fit? Do I need two? I haven't pulled the motor apart yet. Thanks
Reply
Hello Darren - Your Polaris motor would require two of the 203 bearings (5270-31).
Reply
I have an AO Smith pool motor that needs the bearing replaced. The motor number is 0-193984-25. What bearings do I need for this application? Thanks
Reply
Hi, Eric. Our listing shows that Part # 0-193984-25 uses these 203 Bearing on both ends.
Reply
I have a hayward RS 750 pump with a A.O. Smith K48K2N104 this is 3/4 hp I need to know which bearings I need for this motor as they are shot and need replacement (making noise) please advise.
Reply
Hi, Charlie. The K48K2N104 after market motor which is the CT1072 motor uses the 203 Bearing on the OSE and the 304 Bearing on the SE. The OEM motor may use different bearings.
Reply
I have an AO smith motor need motor bearings from the inside part is 0-173840-23 serial 04212ch are these bearings i need
Reply
Hi, Sammy. These 203 Bearing are the correct bearings for the Century Motor p/n 0-173840-23.
Reply
I have a Pentair Century 1hp motor #168887. Will these bearings fit?
Reply
Hi, Rhett. The Part # 168887 motor does use these 203 Bearing.
Reply
I have a century centurion A.O.Smith part # 7-187400-20 CAT# B668 what size bearing do I need? and how many? Thanks in advance.
Reply
Hi Ben, for your B668 motor you will require two of these 203 bearings.
Reply
I have a Hayward Super Pump II (SP-3010EEAZ) with motor SP-1610-Z1-BEE... which bearings does it use?
Reply
Hi, Steve.The Hayward OEM motor uses different bearings from the Century aftermarket replacement which uses the 203 Bearings and the 304 Bearing.
Reply
What are the bearing nos for a 2 HPCentury (AOSMITH) pump motor serial 119083M Century part no 7-196257-07 other number on the motor sticker is BB2843 thanks, mike
Reply
Hi, Mike. The Century B843 motor uses this 203 Bearing - 10000353 on both ends.
Reply
I have a AO SMITH CT1072 Mod K48K2N100A1, what are the right bearings please ?
Reply
Stephane, The CT1072 motor uses the 304 Bearing (SE) and the 203 Bearing (OSE).
Reply
Will these fit Hayward 1.5HP Power-FLO-LX, Model SP1515-Z-1-ES? AO Smith part # 7-193391-02.
Reply
Mike, The PowerFlo LX uses 2 different bearings depending on the age of the motor. Some of the motors use a 6203 bearing while other motors use a 6201 bearing. I would recommend calling Hayward with the serial number on the motor so that they can determine the age and let you know which bearing style you have. You can reach them at 888-429-9273.
Reply
I have a Hayward Super Pump with the AO Smith 7-177653-03 motor (230V 2 speed). What are the correct bearings for this motor?
Reply
Hi, Mike. I was not able to locate a motor with p/n 7-177653-03 so I'm unable to confirm the bearing size. Please double check the Part #.
Reply
I have a a o smith motor 7-184950 22 part number b-w2-28 serial number. 2 hp is this the correct bearing
Reply