Part # 4628-21
Manufacturer Code 39262605K
Alternate Part #'s 39262605K, 39262605R, 39262605RKIT, 4628-21, 601796, JAC-051-2677
INYO # 4628-21 JACUZZI #39262605K
Jacuzzi DVK-7 valve cover kit includes a complete key, cover and handle assembly. This kit will fit both the bolt-on and clamp-on versions of the DVK-7.
The DVK-7 valve is used on a number of Jacuzzi sand filters including the Sand Trap, Laser, and MFM mdoels.
Parts Included:
The handle on our Jandy part number H0323300 broke. Seeing as this is the only
Issue, will this part fit?
The DVK7 Complete Cover Kit - 39262605K will work on your valve, but you can also get just the Handle Repair Kit (39251707rkit). Our guide on How To Replace a Pool Multiport Valve Spring will give you some great tips on how to replace the handle or the assembly.
Reply
What do the six positions do. I have no manual and it was never explained.
Reply
Hi Bill. The filter valve works as follows: 1). FILTER gives a downward flow through the filter bed and gradually restricts the flow of water until backwashing. 2). BACKWASH gives an upward flow through the filter bed that removes the dirt from the sand and carries it to waste. 3). DRAIN is for pumping water from the pool. 4). WHIRLPOOL returns the water to the pool unfiltered. 5). WINTERIZE allows air to leave or enter the tank to help priming and draining. Only to be used when pump is off. 6). RINSE settles the filter bed after backwashing and carries any remaining dirt to waste. 7). TEST prevents backflow of water from pool during pump maintenance if the filter is below water level. The manual for the DVK7 valve used mostly on the Laser sand filters is here.
Reply
will this part fit:
SFTM-MPV (Multiport Valve assembly)
Zodiac/Jandy part #: H0323300 (Valve handle assembly)
Reply
Hi Kim, No this will not fit your valve. You will need to replace your complete valve with this SFTM Replacement Valve.
Reply
Hi does this part fit the Jacuzzi 250L sand filter and does it include the o-ring?
Yes, the DVK7 Complete Cover Kit - 39262605K is the correct replacement part for your DVK-7 valve.
Reply
The cover kit I have has the same number without the K at the end. It is 39-2626-05
Is this the same part as indicated on this site that includes the K?
Reply
Hi Frank, The part # with and without the K will be the exact same thing so you will be fine ordering this part #.
Reply
Last summer I replaced only the part with the spider gasket but i continue to have water leaking at times when i go back to filter after backwashing and rinsing. Do you think getting the entire replacement part address this?
Reply
So usually replacing the spider gasket resolves this issue but sometimes having the originally manufacture assembled valve has the best quality, so I would say that if this has been giving you some trouble to replace the entire assembly.
Reply
What cover kit would replace jacuzzi laser sand filter 225 that is currently leaking at top. We've removed the cover and the number on dial is 39-2626-05 or 39-2626-06 (last number is not clear.
Reply
Hi. This DVK7 Complete Cover Kit - 39262605RKIT will replace the cover that you have on you current valve.
Reply
would this work on Jacuzzi Laser sand filter model 225L? I was looking at getting the 4628-13 key assembly w/gasket because i need new spider gasket,isn't this part included in this complete cover kit? My handle is in bad shape too and figured the labor to install this would be alot less expensive.
Reply
Yes, that will work on the Laser. Can you provide the part number from your valve so I can confirm that is the correct cover kit for your valve. If you do not have that information you can attach a picture of the valve so I can identify it for you.
Reply
Would this work on the jacuzzi laser 190L series?
Reply
Hi, This Cover with will fit either the DVK-7 Bolt Sty. Valve (39262803) or the DVK-7 Clamp Sty. Valve (39263020K) which can work on the Jacuzzi Laser Series depending on which style you have.
Reply
I have the Jacuzzi 7port Model 39263009 DV Assembly that fits on a 225L. Currently leaks. What is the correct replacement model. Is it the 39262605rkit ?
Reply
Hi Larry, Yes this 39262605rkit would be the correct replacement for your Jacuzzi 39263009 valve. This item is the top half of the valve only but 99% of the time the issue with leaking is in the top half of the valve. By just replacing the top half of the valve you don't have the headache of getting involved with the plumbing.
Reply
Just purchased a DVK7 complete cover kit, but it came without any instructions for installing. Are there any instructions available?
Reply
Hello Carol - The installation of this assembly is not difficult. All you need to do is remove the 6 bolts from the old assembly and lift the top off of the valve. Place the new top assembly on the valve body and tighten the bolts.
Reply
I need to replace my original Jacuzzi 7-way filter valve, would installing the 39262605RKIT require any changes to my existing plumbing. Are the plumbing ports in the same exact positions as the original?
Reply
Our inground pool has a Jacuzzi sand filter (Model #DV Assy 7-Pos 1 1/2NPT)(Order #39263009) which is dated 2000.
I have a very small leak coming from the 7 position handle. No other leaks around the piping, of where the bolts attach to the head and tank.
Do you recommend a complete gasket rebuild kit to fix the leak? Do you carry?
Or do you recommend a complete head ass'y replacement. Do this unit that you carry replace my older Jacuzzi 39-2630-09 head?
Reply
I would suggest the complete cover kit here for the Jacuzzi 7 way valve http://www.inyopools.com/Products/07501352015807.htm as there are so many parts within in the top half of the valve which could be causing your leak. You may view the cover kit (Key D) as well as all the other parts of your valve here http://www.inyopools.com/pool_parts_7_way_dial.aspx
Reply
Less than 1 hr
Screwdriver, Wrench Set
Installed kit 14 March, yesterday. Even with no included instructions, the install was a no brainer (very easy). When pump activated and primed, ran for a while then shut off, prime held. The fault was with the grit and gravel bits that sloppy installers left in the system. The dial control could not seal properly.
Less than 1 hr
Screwdriver, Socket Set
Less than 1 hr
Screwdriver
Less than 1 hr
Screwdriver, Wrench Set
The Most Helpful Review
2 0
(5 out of 5 stars) This is the part for you!
Reviewed By: Chuck from Harleysville, PA ()
Pros: Super fast delivery, faster installation, reasonable price, high quality
Cons: NA
If your Jacuzzi/Carvin Dvk7 valve is leaking from the top handle assembly,this is the perfect part for you. It bypasses all of the plumbing efforts required of including a new valve body. This is really the guts of the unit so save yourself the time and money. A total of 10 minutes to swap out the old one which included rounding up a phillips screwdriver and 7/16" wrench.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Part was exactly what I needed. Great online customer service.
Was this review helpful to you?
(5 out of 5 stars) So simple to replace!
Reviewed By: Inyo Customer ()
So simple to replace! Even a pool novice can handle this one. If you can operate a screwdriver you can replace this part!
Was this review helpful to you?
(5 out of 5 stars) Super fast delivery, faster installation, reasonable price, high quality
Reviewed By: Chuck from Harleysville PA ()
Pros: Super easy install
Cons: Not purchasing sooner :)
If your Jacuzzi/Carvin Dvk7 valve is leaking from the top handle assembly,this is the perfect part for you. It bypasses all of the plumbing efforts required of including a new valve body. This is really the guts of the unit so save yourself the time and money. A total of 10 minutes to swap out the old one which included rounding up a phillips screwdriver and 7/16" wrench.
Was this review helpful to you?
1 0
(5 out of 5 stars) Inexpensive repair
Reviewed By: Kurtis H. from Mary Esther, FL ()
Plug and play! New pressure gage was nice bonus!
Was this review helpful to you?
(5 out of 5 stars) Valve replacement kit
Reviewed By: Lind G. ()
My valve handle broke and I could not get the pin out. Couldn't get a replacement valve (delivery was weeks because Jacuzzi was out of business). This kit allowed me to change the guts out on the valve and get back in business within 15 minutes. Solved a big problem for me because I couldn't backwash my filter w/o the handle.
Was this review helpful to you?
2 0
(5 out of 5 stars) Exactly what I needed to get my pool wooking again
Reviewed By: Ray W. ()
Pros: easy install with no worry about getting the gasket or spring installed correctly..
Cons: None
Wasn't sure if I needed just the spring or gasket but after talking to a inyopools rep I decided to just get the complete cover kit. I'm glad i took his advice. The spring and gasket came installed and it only took 5 minutes and we were back in business.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Joel F. from Hartford, WI ()
Pros: Perfect mactching parts replacement
Cons: none
The parts ordered matched up perfectly and the job was completed in 30 minutes- Thanks again for all your help! HIGHLY RECOMENDED!
Was this review helpful to you?