Impeller compatible with Hayward™ Super II 1.5 THP - SPX3010C

Part # 5110-10J

By PureLine

  4.75 Average  

Details

Top

Part # 5110-10J

Manufacturer Code SPX3010C

Dimensions 4.75" X 0.55"

Alternate Part #'s HAY1012071, PL2751, SP3010C, SPX3010C

Product Description

This Impeller is not the Hayward™ original Impeller and is an After-Market generic Impeller by Pureline

After-Market 1 HP full rate / 1.5 HP up rate impeller by PureLine used on the Hayward™ Super II and Super Spa pumps and Leslie's™ Hydromax II

Compatible With

  • Hayward™ Super II™ SP3000 Series
  • Leslie's™ Hydromax II
  • Hayward™ Sper Spa
  • Hayward™ RS Series

*Inyo Pools is not affiliated with Hayward® Industries Inc. The use of such trademarks herein is for informational purposes only, and the goods are not those of Hayward® Industries Inc, but rather they are simply compatible with the referenced Hayward® product.

.

Top

?     Asked on 5/3/2021by paul kazimiroff

Have a new Franklin Electric pump for an in ground jacuzzi replacing an old Franklin Electric pump same Model. Model # 1103092438. 3/4 hp S.F 1.5 hp 3450 FR 56 115/230 v. FLA 1015 SFA 12.8 /6.4 I need to replace the old impeller. No serial numbers on it nor make. Diameter is 4 3/4 in. Intake outer diameter 1 3/4 in . 2 1/4 in. total depth. 1/2 in. diameter shaft thread. Largest diameter wheel 5/8 in thick. The Hayward SPX3010C seems perfect. Is the intake OD 1.75 in. or less? THX
 Reply

A  Answered on 5/3/2021 by InyoPools Product Specialist Patrick P.

Hi Paul, Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply

  • Commented on 5/5/2021 by Product Owner

    detailed views of impeller that came with original Franklin Electric motor 1103092438 whose throat ring sheared off the 4.75 " circular impeller and drawing with measurements. looking to replace the impeller . I think the Hayward I mentioned in the prior note might fit.

     Reply

    • Commented on 5/5/2021 by InyoPools Product Specialist Patrick P.

      Hi Paul, Thanks for the photos! Can you pull any part #'s from the white label which is on the green pump housing, the label next to the discharge pipe on the green housing? Also, do you see any manufacturer names on the green pump housing like Marlow, Purex, Sta-Rite, Swimquip, Anthony, etc.. If you could click the reply link below post any of this additional requested information.
       Reply

      • Commented on 5/6/2021 by Product Owner

        The label on the filter housing cannot be read. Too faded. It is a Purex filter. Have included external and close up internal images with measuring tape against inflow opening in which the impeller inserts. Thus if you have an impeller that is 1.75 in OD maximum or less and the length of the impeller ( depth) along the shaft does not exceed 2.25 in it should work. Thanks.

         Reply

        • Commented on 5/7/2021 by InyoPools Product Specialist Patrick P.

          Hi Paul, Can you check to see if you can pull any part #'s from the basket, lid, impeller or any other parts? Normally these are stamped into the plastic or copper. Normally if we can get any of these part #'s it may lead us into the right direction.
           Reply


?     Asked on 4/30/2021by Josh Nowak

What impeller and seal player do I need for this Hayward super II 1.5 horsepower motor

 Reply

A  Answered on 5/1/2021 by InyoPools Product Specialist Patrick P.

Hi Josh, Thanks for the photos those are super helpful! You will need this Super II Pump™ Style Drive Train UpGrade Kit 1.5 THP - PL2762
 Reply


A  Answered on 5/1/2021 by Product Owner

Thanks - just to confirm I switched out the motor with the Century 1.5 HP Round Flange 56J Up Rate Motor - UST1152 Is this still the same kit for that motor?
 Reply

  • Commented on 5/1/2021 by InyoPools Product Specialist Patrick P.

    Hi Josh, Yes this is the kit that you would use with the UST1152 motor in conjunction with a Hayward Super II
     Reply


?     Asked on 5/20/2020by jeff

what is the part # for impeller ring on impellerSP3010C AND diffusersp30000bn
 Reply

A  Answered on 12/30/2020 by InyoPools Product Specialist Hector F.

Hi Jeff, in order to be sure we recommend the correct parts, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest using our live online chat feature. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 8/2/2019by CHRIS J WILDERMUTH

A similar question was asked but answered with suggesting downsizing a motor. However, my current motor which works is 1.0/1.4HP peak, but the current impeller is the SP3007-C rated for 3/4 HP. Can I upgrade to the SP3010-C? The Dimension photos aren't the same on the two products so I can't compare the sizes.
 Reply

A  Answered on 8/2/2019 by InyoPools Product Specialist Lennox H.

Hi, Chris. You can upgrade to the SPX3010C impeller, only if your filter is large enough to handle the water flow. 
 Reply

  • Commented on 8/2/2019 by Product Owner

    It is a Hayward StarClear C900 Plus. I believe it’s connected by 2” pipe. The pump is on the same level as the pool.
     Reply


?     Asked on 5/19/2019by Bob

My impeller has broken. I am having a time finding the replacement part. I replaced the motor, it's a Century UST1152 1.5 HP. My broken impeller has the part number Hayward SP2610-C. The motor had quit running and when I replaced the motor with the Century, that's when I saw the impeller was broken. Can you help with the correct impeller?
 Reply

A  Answered on 5/20/2019 by InyoPools Product Specialist Hector F.

The best way to really be sure as to which impeller that you need, we will need the model name or number of the front pump housing that the motor bolted to. If you are not sure of that model you can always email us pictures of it to upload@inyopools.com so we can identify it for you. 
 Reply


?     Asked on 8/30/2018by Inyo Visitor

Is it ok fot the full rate ST1152 motor total HP=2.2 running with this spx3010c imppeler? Will it make motor over heated or burned out prematurely?
 Reply

A  Answered on 8/31/2018 by InyoPools Product Specialist Lennox H.

Hi. You can use the ST1152 motor with this SPX3010C impeller without any issues. The motor will not overheat or burn out. 
 Reply


?     Asked on 7/6/2018by ed malley

got a lot of chatter coming from impeller area of hayward 11/2hp rs 1500 i replaced bearing last year when i had similar issue seemed to do the trick but now noise is back wondering if i should replace impeller
 Reply

A  Answered on 7/7/2018 by InyoPools Product Specialist Lennox H.

Hi, Ed. First, inspect the impeller and the impeller ring to see if something is caught in it or the impeller ring is worn and loose. 
 Reply


?     Asked on 6/22/2018by Nick

Replacing the impeller on my Hayward pump. Previous impeller was SP 3010-C. Could not find online other than SPX 3010-C. Is this the same (or can it be used?
 Reply

A  Answered on 6/22/2018 by InyoPools Product Specialist Lennox H.

Hi, Nick. Yes, this SPX3010C impeller is the correct replacement. 
 Reply


?     Asked on 7/10/2017by Mike Martinez

I replace the 1.5 HP motor on my 2015 Super II Pump, the other one burned out, now the out put on the pump with the new motor in very low, will hardly operate the pool cleaner?
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Lennox H.

Hi, Mike. Several system and equipment issues can lead to low water flow or pressure. I would recommend checking out these Inyo Blogs and Guides which can help you locate and correct the cause of this issue, Low Water Flow: Locate and Correct.
 Reply


?     Asked on 7/9/2017by Dave

Super II SP3007EEAZ pump with a 2-sp Century motor. Cat B975, part 177060. HP = 1.0-.12, SF 1.40. Changing the motor to a 1-speed ST1102; also rated 1 HP with SF = 1.5. Pump came with a SP3007-C impeller, which is apparently rated for .75 hp, not 1.0. Do I need to upgrade to a SP3010 impeller? Pump is already more than I need--pool's only 10,000 gallons, but OTOH, if I'm paying the same for electricity either way, maybe the more aggressive impeller, with shorter run-times, is indicated?
 Reply

A  Answered on 7/10/2017 by InyoPools Product Specialist Patrick P.

Hi Dave, If your impeller is a SP3007C impeller then you can go with the UST1102 1HP Single Speed Up Rate Motor which is less expensive and will cost you less to operate then the ST1102 Motor. When replacing your motor we suggest a Hayward Super II Seal Kit.
 Reply


?     Asked on 3/30/2017by shannon

can you use a hayward impeller on a century pump
 Reply

A  Answered on 3/30/2017 by InyoPools Product Specialist Matt S.

Yes, you can use a Hayward Impeller (pump part) on a Century motor. Century/A.O. Smith manufactures the motor, not the pump housing. To make sure you are looking at the right part, match the part number to the one on your current impeller. Or you use the pump housing's model number to find the correct parts breakdown on our pump part's page.
 Reply


?     Asked on 6/12/2016by nestor cruz

I am buying your pump motor # c48l2n134c1 need shat seals part #.
 Reply

A  Answered on 6/12/2016 by InyoPools Product Specialist Matt S.

To find the correct shaft seal, we need to know the model number or make and model of your pump's housing. This motor can be mounted on several pump housing, and each one can use a different shaft seal.
 Reply


?     Asked on 11/6/2015by Art

Do you have a impeller kit with all the part needed to replace impeller and defueser?
 Reply

A  Answered on 11/9/2015 by InyoPools Product Specialist Lennox H.

Hi Art, There is not a kit that includes the impeller and diffuser for the Hayward Super II Pump, these items will have to be purchased separately.
 Reply


?     Asked on 9/11/2015by Inyo Visitor

How tight should impeller be tightened?
 Reply

A  Answered on 9/15/2015 by InyoPools Product Specialist Lennox H.

Hi, The Impeller would be hand tightened onto the motor shaft.
 Reply


?     Asked on 5/27/2015by Roy Hughes

How do I remove the impeller from a Heywood pump\motor?
 Reply

A  Answered on 5/27/2015 by InyoPools Product Specialist Patrick P.

Hi Roy, Here we have a Video on How To Remove a Hayward Impeller which will go over all the steps you need to take to remove your impeller.
 Reply


?     Asked on 10/25/2014by Minh Vu

After I changed the new impeller, why is water leaking out from the bottom of the pump?
 Reply

A  Answered on 10/26/2014 by InyoPools Product Specialist Patrick P.

Hi Minh - This is most likely your shaft seal which needs to be replaced. If you have the Hayward Super II then you would need the Hayward Super II Shaft Seal we also carry a Hayward Super II Tune up Kit which includes the shaft seal as well as all the o-rings and gaskets for your pump. I typically would recommend going the Tune up Kit route as this will ensure that you are replacing all the items which typically cause this leak.
 Reply


Top

Review Summary

 (Average 4.75  out of 5 stars)
12 Rating
5 star:
 
(9)
4 star:
 
(3)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews