Pureline Generic Super Pump™ Style Seal Plate - PL2670

$32.99

IN STOCK
FREE SHIPPING

Part # PL2670

By PureLine

  5 Average  

Details

Top

Part # PL2670

Alternate Part #'s SPX2600E5

Product Description

Pureline Generic Super Pump™ Style Replacement Seal Plate

This is an aftermarket generic Replacement Seal Plate compatible with the Hayward® Super Pump™ 2600 Series which fits Hayward® Super Pumps™ manufactured 1984 to present.

This seal plate is compatible with Super Pumps™ .33HP - 1.5 HP both full rate and up rate and for 2HP up rate.  The SPX1611E5 seal plate would be for the 2 HP full rate and 2.5 HP up rate models. This is the seal plate only and does not include any other parts or accessories.

Disclaimer:

All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.

Product Specifications

Manufacturer:
Pureline
Top

?     Asked on 10/30/2022by Inyo Visitor

my pump is leaking from the area of the shaft what do i need to replace and correct the issue.
 Reply

A  Answered on 10/30/2022 by InyoPools Product Specialist Hector F.

Hello, if you have a Hayward Super Pump series pump then the correct seal kit for a chlorine swimming pool is the GOKIT3. If you have a saltwater swimming pool then that will be the GOKIT3SALT
 Reply


?     Asked on 7/20/2021by Eric

Would replacing this plate (and seal) be a tight fit back on the motor, or should it slip on easy?
 Reply

A  Answered on 7/21/2021 by InyoPools Product Specialist Craig C.

Hello Eric.  The Pureline Super Pump Seal Plate with motor shaft seal installed should easily slide down the motor shaft and butt against the motor mounting plate.  Attached please find an exploded part diagram which may assist in visualizing how these parts are installed.    Hayward Super Pump SP1600 & SP2600 Series
 Reply


?     Asked on 7/14/2019by Larry Moore

I replaced the seal on the housing. I leaks worse now than before. What could it be?
 Reply

A  Answered on 7/14/2019 by InyoPools Product Specialist Lennox H.

Hi, Larry. The shaft seal could be installed incorrectly and or the seal plate could be warped. 
 Reply


?     Asked on 6/27/2019by MIke B

my pump is leaking do i need the seal kit to fix this ?

 Reply

A  Answered on 6/27/2019 by InyoPools Product Specialist Matt S.

If your pump is leaking from a seam, then a gasket most likely the problem. The gasket kit for the Hayward Super Pump is the GOKIT3 or the GOKIT3SALT. But I would try opening your pump to determine where the leak is coming from first; there may a crack in one of the hardware pieces.
 Reply


?     Asked on 6/17/2019by Jeff

Do I need to also purchase the bolts for the motor mount? This purchase will be used with the 2607c impeller and the Smith 1 HP motor. That grouping is replacing the old Hayward Super Pump. I already have the GoKit. Thanks
 Reply

A  Answered on 10/1/2019 by Industry Professional

You need to order screw for motor housing are 5110-15 screws for motor cap 5110-16 SEE PARTS BREAK DOWN 
 Reply


A  Answered on 9/30/2019 by Industry Professional

Yes you will need to purchase the bolts as well. 35-150-2036
 Reply


?     Asked on 5/19/2019by Inyo Visitor

i HAVE A 1 HP MOTOR, WHAT SEAL PLATE DO i NEED
 Reply

A  Answered on 5/19/2019 by InyoPools Product Specialist Hector F.

The seal plate will be based on the model name or number of the front pump housing that the motor bolts to. If you do not have that information then you can email pictures of it to upload@inyopools.com so we can identify it for you. 
 Reply


?     Asked on 8/21/2018by slade

Hello: I have a leak between my seal plate and motor mounting plate on my rs750. When I replace them do I use sealant, or just bolt them together.
 Reply

A  Answered on 8/22/2018 by InyoPools Product Specialist Hector F.

You do not need silicone for replacing these parts. Just standard o ring lubricant for the housing gasket.  
 Reply


?     Asked on 7/12/2017by Glenn Cullen

do you have a seal plate kit for saltwater. Description of the plate kit does no indicate seal is for saltwater.I need the motor mount, the seal mount plate, the seal for salt water, and the gaskets. If I order the salt tune up kit, and the seal plate kit, I end up with two seals, one fro salt, one not.
 Reply

A  Answered on 7/12/2017 by InyoPools Product Specialist Patrick P.

Hi Glenn, Unfortunately, we do not have a seal plate kit for saltwater. The seal that is in the kit can be used on salt pools but just won't last as long as the heavy duty seal included in the Tune Up Kit.
 Reply


?     Asked on 6/26/2017by vinny

are these pumps like car water pump when the seal goes bad does the water leak out the little hole in the bottom of the pump and if so how do you get the pump off in order to change the back seal
 Reply

A  Answered on 6/26/2017 by InyoPools Product Specialist Alex V.

Vinny, Yes these pumps are similar. What model pump do you have? The process to change the shaft seal can vary depending on the pump model. 
 Reply


?     Asked on 9/18/2015by Inyo Visitor

Does this include the impeller?
 Reply

A  Answered on 9/18/2015 by InyoPools Product Specialist Matt S.

The SPX1600SKIT1 Hayward Super Pump Seal Plate Kit does not include the impeller. The impeller must be purchased separately and matched with the motor's Horsepower output.
 Reply


?     Asked on 6/18/2015by Inyo Visitor

how do you remove the seal plate from the pump motor? I have a pump that is seized and want to remove the plate to see if I can manually turn the pump. However, I am unable to remove the plate from the Hayward motor.
 Reply

A  Answered on 6/18/2015 by InyoPools Product Specialist Dennis R.

See our guide on "How To Replace the Motor on Your Pool Pump". It shows you step by step how to replace a Hayward motor including how to remove the seal plate.
 Reply


?     Asked on 5/4/2015by Inyo Visitor

Their is water dripping between motor and plastic connection.
 Reply

A  Answered on 5/4/2015 by InyoPools Product Specialist Brian M.

The most likely case of the problem is a bad shaft seal.  It would be part number 5110-11 If, while you are inside the pump, you wish to replace all the o-rings, there is a kit called a GOKIT3
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Nut Drivers, Socket Set

Had leak

Written on 8/16/2019 by Guest

Replace the old one because it was leaking. Great fit.

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

4 to 8 hrs

Tools Needed

Screwdriver, Pliers, Socket Set, Wrench Set

Old motor went out. My seal plate was about 30 yrs old and looked like it was letting water seep by. So i decidec to rreplace it

Written on 3/18/2017 by Guest

I ordered new motor and seal plate and other parts and watched several of Inyo's how to video's and replaced all of the parts along with the motor. It was quite easy!

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
19 Rating
5 star:
 
(19)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews