I have a Hayward Super Pump (SP-1610-Z1-M) 1.5 HP. Can you please inform me as to what bearings I should order for replacement. Thank you.
Reply
Hi Rick, You would require one 203 Bearing and one 204 Bearing.
Reply
I have a power flo matrix 1hp. A.O. smith motor. The motor bearings are going out, what bearings do I need.
A.O. Smith #SP1510Z1XEHC
Part #O-196035-20
Frame Code #P48Y
Thanks
Scott
Reply
Your motor would require two of the 6203 Motor Bearings.
Reply
I don't know if dis is the right bearing bat I need a bearing for a American products motor type cx cat/n B661 or8661 part/n 8-165198 and the price tank you
Reply
Hi Juan, I am showing that your motor uses two of the 6203 Motor Bearings.
Reply
i have a century lasar ,a o smith 2 hp
bn37 i need both bearings which one will fit
thanks
Reply
You would need two of the 6203 Bearings for the BN37 motor.
Reply
I have a century/aosmith pump motor b2853.which bearings do I need?
Reply
Hi, You will need 2 203 Bearing (62032RS) for the B2853 motor.
Reply
I have a Intek 633T motor what bearings do I need?
Reply
Hi JohnK, We do not have that information on the Intex Krystal Clear 633T Filter Pump. You would have to contact Intex at (800) 234-6839 for that information.
Reply
hi there i have a century B2853 pool motor and needs the bearings for it is this the right part #
Reply
Hi Jose, Based on the information we have the B2853 would use one 203 Bearing (62032RS) on either end.
Reply
I have a A.O. Smith E-Plus 2 hp 1.30 SF pump, S/N BZ05-21, P/N 7-177452-03, Type CX FRY56Y, 3400rpm. I need both bearings and there is no designation on the bearrings?
Reply
Hi Kort, The motor with p/n 7-177452-03 will use (1) 203 Bearing (62032RS) on the shaft end and opposite shaft end.
Reply
I have both a Pentair Challenger 2.0 HP pump and a Challenger 1.5 HP pump. Which motor bearings go with each of those models?
Reply
Hi Craig, If you can provide the motor's Part, CAT, or MOD number we can located the bearings.
Reply
Can you please tell me which motor bearings I need for a Hayward SP2610X15
Thank you
Reply
Hi Vince, You will need (2) 203 Bearing, one on either end the motor used on the SP2610X15.
Reply
I have a Haward Super Pump 1 hp SP1607Z. What bearings would I need to rebuild the motor. Thank you
Reply
Paul, If you have an uprated 1 HP motor with a SF of 1.1 (see motor label), its bearings are 604005-001 front and back.
Reply
What motor bearings would I need for a US Motors 1081 pool motor. not sure what you need from the label, but it is a 1 HP, S.F. 1.40 RPM 3450, model K63CXEPY - 4766, CAT No EB654.
Reply
Hi Chris, We do not have the bearing specs or part list for the US Motors so can't confirm if this bearing will fit.
Reply
Century Centurion motor bearings are noisy. Please describe the bearing type and part numbers for front and back of the motor horizontal mount pool/spa duty:
Pump Motor A.0.Smith Part No. 0-193994-06 HP: 2 Frame: Y56Y RPM 3450
Reply
What bearings would I need for a AO Smith century two speed motor cat B985 with a HP 2.0-.33 RPM 3450/1725 volts 230 FR Y56Y
Reply
Hi. The B985 motor uses the 304 Bearing on the Shaft End and the 203 Bearing on the opposite shaft end.
Reply
Have a Magnetek century spa &pool pump with noisey bearings numbers on bearings are ntn 6203L6 and can not fne where can I find or what can I use
Reply
Hello Don, we have a Bearing, 203 (62032rs) (Single) if you would like to just double check with Century you can contact them 937-667-2431
Reply
I have a Pentair model# LA01N 3/4 HP motor serial# 1-22-K06. what bearings do I need? Also, are there any additional parts I need when I replace these? Thank you in advance.
Tim
Reply
I have a 3/4 hp china infinity pool pump sp-600 series need 2 bearing and seal my bearing part #6202RZ bom 019 3a
sealed . the pump seal # LX that all I have
mike can you help
thank you
Reply
Hi, Mike. Based on the specs I was able to locate on the 6202RZ bearings, this 202-LL bearing can work as a replacement.
Reply
I have an A.O. Smith pump motor- part 7-177452-03 RPM-3450 volts 208-230, for a 2 HP whisperflo pump. what bearings will I need and is it easy to replace the bearings?
Reply
You will need two of bearing part number 5270-31 and as far as difficulty, it ultimately depends on how handy you are. Here are the 2 guides that we have made for replacing pool pump bearings so you may asses the difficulty for yourself.
Reply
I have an AO Smith electric motor for my pool pump 1 hp., 230/115 volt, 1 phase, motor #168453, 3450 rpm, motor package #355340S, Code J. Can you tell me what bearings and seal I need for this motor? Are they difficult to install?
Reply
Hi David, the bearings on this page are not the correct bearings, you will require two of these 203 Pool Motor Bearings we would need to know the make and model of your pump to be able to suggest the proper seal kit. The bearings are not the easiest thing to install, we do have a Video on How to Install Pool Motor Bearings which you should find helpful.
Reply
I have a waterway SD-20-2N11CD center discharge pool pump, what bearings do I need for replacement.
Reply
Hi, Joe. The motor for the SD-20-2N11CD pump uses the Single Sealed 203 Bearing - 10000379. We do not carry this bearing.
Reply
I would like to find the bearings for a magnetec M century motor. Part # 8-177132-01, Serial BG4-171 I hope this is enough information. Thank you.
Reply
Hi Jim, You will require two of these 203 Pool Motor Bearings for the motor you have listed.
Reply
I have a Hayward EcoStar SPX3400Z1ECM 2.7 Hp that needs motor bearings. I don't see a listing for it...could you tell me which bearings I need?
Reply
Ted, The Hayward SPX3400Z1ECM Motor uses (1) 6203 and (1) 6204 bearings.
Reply
Which bearings for wfe-8?
Reply
Hello Tina - You would require two 203 bearings for the Pentair WFE-8 motor.
Reply
I'm looking for bearings for a Sta-Rite DJAYFA-0101 pump. Can you point me in the right direction? Thanks.
Reply
Hi, Unfortunately, we do not sell replacement bearings for the motors used with Sta-Rite DJAYFA-0101.
Reply
I'm trying to track down which bearings I need for a BN37 7-177782-03 R48Y CSM the HP and SF are blank on the form on the side.
Reply
Hi, this fall I might overall a similar hayward dual speed pool motor with the following ID: SP-1610-Z2-M* (can't read the last *). There's also a A.O Smith ID: C*8L2N130. I believe it's C48L2N130 which you have listed on your web site. Do I need the same bearings has the SP-1610-Z-1M (203 and 204).
Thanks.
Reply
Hi, Michael. The same size bearings are used in the dual speed motor as well.
Reply
Hi I am looking for the bearings for my Hayward/Century motor SP1515-z-1-ESC. it is the 1.5hp please help. thanks
Reply
Hi. Unfortunately, our listing does not list the bearing for OEM motor. You will have got take the motor apart to confirm the bearing size.
Reply
what bearings would I need for my CAT-B121 3/4 hp motor, type - CX for the pool& spa. , 230/115 volt, code J, ENCL -DP, FR- s560, FORM kjm, SER- BU 11-20, PH-1
Reply
What's part bearing number for PENTAIR motor # 193508
Reply
Hello, This will be the bearings you will need, http://www.inyopools.com/Products/07501352012909.htm You will need two of them.
Reply
saw this bearing is rated for 2hp...my pump is a 3hp motor will this still work on motor bn61 a.c smith,,
Reply
Hi Kevin, The BN61 motor requires two of this 203 Bearing
Reply
Looking for bearing 6202Z
Reply
We do not offer the specific 6202Z Single Shield Ball Bearings, the inner diameter is 15mm, outer diameter is 35mm. We have the Motor Bearing, Generic 6202, 15mm Id, 35mm Od ( NA-6202-LL) http://www.inyopools.com/Products/00101352088111.htm
Reply
Can you tell me what bearings fit an A O Smith 196035 pool pump motor.
.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
.jpeg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "U.S. Seal Manufacturing Bearing, 202 Ntn 6202-ll (6202)")
Hello Danny. The correct motor bearing compatible with the AO Smith motor 196035 is Century Motors Bearing 203 (single) -62032RS part # 5270-31. The motor requires a quantity of 2 to complete the project. Bearing, 203 (Single) - 62032RS
Reply
3/4 hp USQ 1072, which bearings to order.
Reply
Hello Ed. The Century Motors 3/4 HP model USQ 1072 would require quantity two (2) of the U.S. Seal Bearing part number 6203. Bearing, 203 (Single) - 62032RS Attached please find an exploded parts diagram for the USQ 1072. Century / A.O Smith USQ 1072
Reply
Which bearings would I use for my SP3220Z1DV motor?
-0f707167-2f79-40bb-9b02-0ed20d1cbff4.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
-0f707167-2f79-40bb-9b02-0ed20d1cbff4.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "U.S. Seal Manufacturing Bearing, 202 Ntn 6202-ll (6202)")
Your motor will take two of these 6203 Pool Motor Bearings. We have put together a couple of videos on How to Replace Pool Motor bearings which you may find helpful when you tackle this project. Video on How to Replace Motor Bearings - Part 1 and Video on How to Replace Motor Bearings - Part 2
Reply
what is bearing(s) required for Century motor B-229SE
Reply
Hi John, you would need a Bearing, 203 (Single) - 62032RS for the outside bearing and a Bearing, 304 Ntn-6304-ll (6304) for the service (shaft) end bearing.
Reply
I have a Century 1.5HP pool motor F56AC20Z01. I want to buy replacement bearings. Would you be able to provide me with the part numbers?
Thanks
Hello, your B2854 motor will take two of the Pool Pump Motor Bearing, 1.5748" OD - 6203, which is part number 5270-31.
Reply
