What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
my pool pump is making a high pitched noise and it getting hot
it is working but very noisy
what could it be that is causing this noise ? the pump is about 12 yrs old 1.5 HP inground pool
Reply
Good afternoon. The high pitch noise is the bearing starting to go. I can not say how long you have before it gives out. It could be a matter of days or weeks. The bearing are starting to stick which in turn causes more heat.
Reply
Does this pump have a toogle switch to turn on or off? i have a pump now that i
have to pull the plug to shut off.
Reply
John- The 1/2 Hp W/ Switch (SPX1515Z1E, SP1515Z1E) part # 5111-87 does come with the switch to turn it on and off.
Reply
The motor on my Hayward SP1510z1 is making a lot of noise and need to replace it. What motor model should I get that would be compatable with the Hayward DE filter SYSTEM.
Reply
Hi Maria, The SPX1510Z1XE motor is the correct replacement compatible with your partial model number.
Reply
My motor # is SP1515-Z-1-EFTC. Part # 7-193771-02. 1.5 hp, 115 volts. What would be the right motor replacement for this? Thanks.
Reply
I have the Hayward Power Flow motor part number SPX1515Z-1-EFTC. This has 1.5 hp with switch and timer. What is the replacement motor with timer and switch?
Thanks
Reply
Yes that would be the correct replacement motor for your power flo.
Reply
Have a SP1515-Z-1-ECS Hayward Power-Flo Matrix is this the correct replacement? Thanks. Jcb.
Reply
I have a SP1515-Z-1-ECS Hayward Power-Flo Matrix. Is there a Dual speed replacement pump for it? Seems like dual speed is the way to go?
Reply
I have this motor and it ceased up yesterday then tripped the breaker. Every time we turned it back on it trips it right away. Would this be the motor or a breaker issue?
Reply
If the breaker is still tripping then it is not likely the breaker and more likely an electrical issue or the motor.
Reply
I have a sp-1515-z1b and i cant read the pump number i need a new seal kit and don't know which one i need the shaft is .500 diameter can you help?
Reply
Hi. We can identify the pump if you can send us pictures of the pump housing.
Reply
I have a Hayward SP1520Z24ESC two speed motor, the old part number is 7-193824-01. What is the correct replacement part?
Reply
Hi, Mark. The correct replacement motor is the SP1520Z1ESC motor.
Reply
I have a Hayward or AO smith motor SP1514Z2S4EC, What is the replacement part for this?? My Switch not working properly, can i just change out the switch?? if so, what is that part number for the dual speed pump?
Reply
Does the Century(Haywood power flo matrix) 1,5HP motor SPX1515Z1E have a start up cap? is it the beige ceramic one behind the endbell?
Reply
Hi, Steve. This Hayward motor does not have an external capacitor.
Reply
How to connect a Hayward motor SPX1515Z1E (115v only) to a 230v circuit breaker (4 wire - red, red, blk, green ), Do I just neglect one of the red wire?
Thanks!
Reply
Hello Tom, unfortunately there is no way to hook up something like a 115v to a 230 breaker, you would end up blowing out something.
Reply
i have a Hayward Power Flex Model # SP1515-Z-1-ES and my power switch went out. What is the replacement number ? I need to order a new one.
Reply
Hello Tabitha, I apologize, but just the switch is not available, the motor for this unit is Motor 1 1/2 Hp W/ Switch (SPX1515Z1E, SP1515Z1E).
Reply
My pump label said SP1515-z-1 ESC, Can I just replace the switch? If so, what is the part number? What are other replacements options for this pump?
Reply
What part number is the cord for pump SP1515-z-1-esc?
(6' with plug and receptacles. NOT the twist lock)
Reply
The part number is 3118-0 for the 3-Prong Pump Power Cord, 3', 14 GA, 115V (SPX1250WA)
Reply
I have a Sp1520Z24ESC pump that will work on high speed but trip's the breaker when switched to low speed what could be wring.
Reply
Hi, Bob. If this is a new pump then the wiring could be the issue. If not and it worked fine before, the motor is bad and will need to replace.
Reply
my haywood matrix power flow 1.5 hp , sp1515z1esc shuts off after i hour the timer is set for 8 hrs.
the electrical outlet has been replaced help
.
Reply
Hi, Fred. You can use the A.O. Smith Troubleshooting Manual to determine the what is causing the motor to turn off.
Reply
I need to replace a pool pump motor for a Hayward PowerFlo Matrix.
The Hayward pump number on the impeller housing is "SP15931TLFP.
The motor is A. O. Smith part number - 7-193391-02. (SP1515-Z-ESC)
Serial # is - CA02-25
H.P. = 1.5
Service frame - 1.00
FR - R84Y
Code - H
RPM - 3450
Type - SP
Time - cont.
HZ - 60
Insul class - B
Phase - 1
Is this replacement motor the one I need?
15 amps, 115 volts
Reply
I have 2 questions:how hard is it to change the new motor to the old housing? And can I use my power cord from my old pump for the new pump?
Reply
Hi, Ken. The difficulty level is based on the customer skill set. You can use your existing power cord with the new motor. Check out our How to Replace an Above Ground Pool Pump Motor.
Reply
I have an sp-1593. I was replacing the bearings and found that my engine cover has pretty much rusted onto the shroud assembly. Do you guys sell just the engine cover and through bolts?
Reply
Many design changes occur every few years, the motor manufacturers are not going to have these parts available separately. We would recommend a new motor.
Reply
I have a Hayward Pro-Flo Matrix that uses the Century sp1515Z1ESC motor which is only 3 years old and today the pump motor did not start and I have 120v into the motor. What could cause this and can it be repaired?
Reply
Possibly a start capacitor or insufficient voltage being delivered to the pump. look for burning on connecting wires and see if the cylindrical cap behind the end pack is leaking fluid.
Reply
I have a haward powerflo matrix pump model sp-1515-z1-FSU. Is your part SPX1515z1E the correct replacement? Is there anything else I should consider replacing as well?
Thanks,
TJ
Reply
Hi, TJ. This SPX1515Z1E is the correct replacement. You will also need the PowerFlo Matrix Pump Tune Up Kit - GOKIT74.
Reply
The bracket under the motor rusted off. do you have anything to replace it with? everything else works good. I don't want to replace the motor because of a broken support bracket.
Reply
Hi, Jerrie. Unfortunately, the base is not a replaceable part. You will have to rig something to support the motor or replace it.
Reply
The 3-prong plug on my motor SPX1515Z1E gets too hot and the prongs 'burn up", first...why is this (electrically), and if I were to replace the cord/plug, what size conductors and plug amp ratings would I use? 1.5 HP 115vac
Reply
I am not sure how you have it wired, however, it must connect only to a grounding-type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Do NOT bury the cord. Locate cord to minimize abuse from lawnmowers, hedge trimmers, and other equipment. Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI.
Reply
It looks like my pool pump motor went bad, it is a century motor, SP150Z24ESC, Part # 7-193824-01. The name plate says it is a 2HP motor, but when I cross it on your website a 1.5HP motor comes up. Is this correct?
Hi Rich, the correct replacement motor for your motor part number 193824 is the 5111-88. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Looking to replace my Hayward Power-Flo LX filter motor. Just trying to make sure I get the correct replacement motor. The manual parts list is shown below along with a picture of the motor.
1.5 HP OA Smith C48L2N134B1 ser: 14610CH; 115/230 volts
Hi Rick, The manual shows a Power Flo LX but your motor photo shows a super pump and these two pumps do use different motors. Can you confirm inf you need the motor for the Power Flo LX or the Hayward Super Pump?
Reply
OK, thanks for that clarification. The picture is the one currently being used on my filter. So that is the one I want to replace. Hopefully take the one off and put the new one on. I also believe there is a kit required to replace the mechanical seal, but not 100% sure.
Reply
Thanks Rick, You will need this UST1152 Replacement Motor and this Hayward Super Pump Seal Kit
Reply
Looking to replace Hayward Power Flo Matrix SP 1515-Z-1-ESC. Do you carry this motor?
Hi Santi, yes, this is the correct replacement motor for the motor included in your photo. You will also need a Hayward PowerFlo Matrix seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I need to get this pump as soon as possible. How long will shipping take?
Reply
Hi Rhonda, motor orders are delivered on average of 3 business days however you can expedite these. Once added to your cart you can select the shipping method with an estimated cost.
Reply
Help! Our motor has gotten really loud and I'm assuming we need to replace it. It has a switch and a 240 cord. Do you have a replacement for it? I'm including photos. Thank you!
Hi. I have a Hayward Power Flo LX model SP1514Z2S4EC and the motor has gotten really loud. When I search for this on your site, it brings me to a Single Speed motor, where the one I have is dual speed. Which would be the correct motor for this pump?
Hi Greg, thanks for the photo! You will require this Power Flo LX Dual Speed Replacement Motor as well as this Hayward Power Flo LX Shaft Seal.
Reply
I have a Hayward SPX1515Z1E Motor. Is this a capacitor start motor or Capacitor run motor ??
Reply
Hello Charles. According to the manufacturer, the Hayward Pool Products motor model SPX1515Z1E is Capacitor Start, Induction Run.
Reply
Hi -
I have a Hayward SP1515Z1BC and I see the SPX1515Z1E is the replacement motor. Do I need any other replacement parts to do this job correctly?
Reply
Hello Lisa. The Hayward Pool Products Motor model SPX1515Z1E is the correct motor replacement for the SP1515Z1BC. It is recommended that the motor shaft seal, housing o-ring, and strainer o-ring be replaced concurrent with the new motor. Attached please find an exploded parts diagram for the Hayward Power-Flo LX Pool Pump. Please note Key items numbers 3, 4, and 12. Hayward Power-Flo LX These are the parts necessary to complete this project.
Reply
