Part # 94027115
Warranty 1 Year
Alternate Part #'s 15UMF-S, 15UMFS, 9402-7115
Patented air-cooled heat sink allows pump to run dry without damage to shaft seal. UNCONDITIONAL ONE YEAR WARRANTY AGAINST SEAL FAILURE.
Exclusive dual Ring-Lok™design gives "tool free" access to strainer basket and pump internals.
208 cu. in. (3411 cm3) heavy-duty strainer basketwith exclusive priming tubefor superior priming capabilities.
Exclusive flap prevents debris in the pump strainer, skimmer basket and filter from flowing back into the pool. The flap also prevents residual hot water in the heater from flowing into filter and causing damage to grids, valves, gaskets, etc.
Internal ribs in large strainer basket assure flow, even when filled with leaves and debris.
One-piece casee liminates bolts and gaskets and provides for quiet operation.
Flexible connections- 2" (51 mm) FNPT or 2" (51 mm) unions (included).
Floating eye seal between closed impeller and diffuser maximizes efficiency.
Maximum water temperature 104 °F (40 °C).
Energy saver motors(1/2 HP - 3 HP) are standard on single speed units.
Dimensions of the Jacuzzi Magnum Force pump
Performance of the Carvin Magnum Force pump
Is this a dual or var. pump? When I hit details it gives me Pure line info. Is this pump still available? Is it Calif. compliant?
Hi, Bill. This is a single speed pool pump, we do not have a dual speed version of this pump. However, their is a variable speed version that can be special ordered, the Magnum Force V Series 1.65HP Variable Speed Pump (15VMF-S) - 94026117. The PureLine Prime 2.7 HP Variable Speed Pool Pump - PL2606 is also a suitable option.
I have a jacuzzi magnum force 1.5 HP pump for inground pool. What pumps are a direct replacement for same hookup with inlet and outlets?
Hi Mark. The Carvin Magnum Force Pump will be a direct replacement. You will need to confirm the service factor of your pump to make sure you get the correct 1.5 hp model pump.
What pumps do yoU sell for my 300000 gal I ground that will run on 110 volt
Hi, Edward. We do have a few pumps that you can uses, however, we will first need to know the Total Dynamic Head (TDH) and the turnover rate. To calculate the TDH of your pool, use the info provided in these Inyo guides How To Measure Total Dynamic Head With Gauges and How Do I Calculate Feet of Head for My Pool?
I have Jacuzzi Magnum Force pump 1UMF-Spump with 7-184948-22 1HP motor. I am planning on adding solar collectors on my 2 story roof for heating the pool water, and they are recommending a 1.5 HP pump. Your recommendations for pump/motor replacement?
Hi, Greg. You will definitely need a larger pump. However, the size of the pump will be based on the number of panels, plumbing size, etc. You can use this Magnum Force Pump 1 1/2 HP Pump if they confirmed it will be sufficient.
Hey, I picked up a used Jacuzzi - 15UMF-5 / 94027115 date 23JUN00. I do not know if the motor is wired for 240 or 120 vac. How can I tell which one it is?
Hi, Rick. You can use the motor wiring diagram located on the motor to determine how to wire the motor based on your breaker. It can be wired for either 115 or 230 volts.
where can I find the motor support? Motor Support (12112405r000) Is this the correct one?
Hi, Mason. The Motor Support - 12112405R000 is the correct for the Magnum Force Pump. We do have them available.
part# 7-184949-22 hp 1.0 (1.65sf) what is replacement pump?
If you are needing the Magnum Force with this matching motor then this would be the correct complete pump. If you are needing the replacement motor then that would be the model 5222AX.
i need to replace a pool motor plus pump. The motor is a Century Centurion and the pump is a Jacuzzi - Magnum Force. The manufactures label for the motor shows 2.0 HP, but there is also a label that shows Total HP = 2.4. Question - what actual HP do i need? Thanks
Yes if you have a 2hp motor with a higher Service Factor then you would go with this unit. You can also go with Magnum Force V Series 2.7HP Variable Speed Pump (VMF-S2) - 94026140
Do you have this with a side mounted capacitor motor (shorter length) fully assembled? i'm limited on space
I'm sorry we do not have this available with a shorter capacitor.
What gauge wiring would you recommend for the 1.5 HP pump, with the 16/8 Amps ? Would this wiring work for 1.5 HP with a 18.6/9.3 Amps.?
Hi Bob for 230V wiring we suggest 14 gauge wire up to 50', 12 gauge wire up to 100', 10 gauge wire up to 150' and 8 gauge wire up to 200'.
What is the overall length? Motor + pump
The overall length is 27-18"
i have a pentair 3/4 hp pump can i replace it with a magnum 1 hp pump.
Jack, It would depend on the Pentair Pump that you have. The Magnum will replace the Pentair Whisperflo.
My pool pump & motor ran for nearly six hours with multiport valve on closed. I found the motor still running with no water in pump skimmer basket. I opened the lid and water rushed in from pool side. I Set multiflow to filter & turned back on. water began blowing out the band clamp between pump and motor with no pressure register to the filter tank gauge. I lost 3inches of water from pool. Is my pump shot or can it be repaired? What Parts do I get to systematically check out the pump function
John. I would consider the pump shot because it will be expensive to repair. You may have to replace the drive end which is the parts from the diffuser to the seal housing depending on what went bad.
Is the housing for magnum the same for all horsepower motors. I would like to downgrade from 1.5 to 3/4 horse power. Thanks
Hi, Frank. The housing is the same on all the different hp. To downsize the pump from 1.5 to 3/4 you'll need to replace the motor, impeller, diffuser, eye seal, and the pump seal and o-rings. Replacing the complete pump model # 94027107 may be cheaper.
The pump motor has died on my Magnum Force Pump 1 1/2 HP Pump - 94027115 unit. Please recommend a replacement motor. Thanks.
I have a 20,000 gal. in ground - my Jacuzzi Magnum Force pump lasted 15 years. Pool is run on salt chlorine generator. Numbers on pump are 1UMF-5 &94027110. Not sure of horsepower. Want to buy new pump from you. Will my current piping connections work with the new pumps? What horsepower do you recommend & which pump? I have a 200 pound sand filter - pool is not heated. Am running 230 volts Thanks
Hi, Stuart. You currently have a 1 HP Magnum Force Pump. Since that pump has worked for 15 years a would recommend replacing it with the same Magnum Force Pump 1 HP Pump - 94027110.
I have a magnum force jacuzzi 15umfs unit installed in 2001 when then the pool was built. I was told that a different type of pool pump like a 2phase Pentair is lower cost electricity and higher efficiency what do you think about updating it?Pentair IntelliFlo 3 HP Variable Speed Swimming Pool Pump 4x160 VS-3050 011018 is what I was considering. but I think that is a 3hp unit vs the old 1.5
Hi, Neil. If you do not want to get a 3 HP pump because it's more pump that you need, then you have several different options. The Raypak Variable Speed Pool Pump - PS165VSP is the best replacement we have available. You can view other variable speed pumps via this link > Variable Speed Pumps.
I have 13 y/o jacuzzi magnum force 94026115. Would a current Carvin jacuzzi be an exact replacement including the quick connect connectors? What is the model number to order from you?. I live in Carlsbad CA? Will your diy video help me in install. It seems like it would be easy as I do a lot around the house. I have experience with in ground sprinkler install and repair and this seems like it would be similar.
Bob, There is two other body style that are a little different. You should still be able to use it but confirm here.Jacuzzi Magnum Parts
Hi! I currently have a jacuzzi magnum force 1 1/ hp 3phase for the jets on my hot tub. If i would like to convert it to single phase, what would be the best option so I can still have the same force I am getting from my jets?
Hi Joe, This Jacuzzi Magnum Force Pump is the single phase option for the 1-1/2 Hp 3 Phase Jacuzzi Magnum Force pump with the same performance.
Sorry, that Magnum Force order number is 94027120. Thanks again. Jim
Jim, Yes the Jacuzzi 94027120 is the 2 HP Magnum Pump if you want the 1-1/2 HP version then the pump here i the pump you are looking for.
I'm replacing a Jacuzzi 2UMF-S Magnum Force pump with a 1 1/2 HP motor (looks like a replacement motor ((UST 1152)). Would your 1 1/2 Magnum Force pump be the ticket? Thank you.
Hi Jim, the 2UMF-S is the 2 HP Magnum Force Pump if you want to step down to 1-1/2 HP then this pump here is the correct pump.
Hi, I have a few questions. 1. Does this 'pump' include the motor, pump housing, impeller, basket, etc.? 2. My bad pump has a sticker that says '2004 Magnum Force 15UTMF-S' (not -S2), motor is two speed, 1.5 HP, Order# 94027215 Is this a standard setup? ( I see you have the 94027115 with this setup) 3. Local chain sold my wife just a motor, STS1152R, it looks compatible, but at $400, I'm wondering if you have the entire setup for a similar price and I can take the motor back. Thanks
Hi Robert, This is a complete pump with motor and housing. This pump is a single speed not a dual speed, we do not have model # 94027215 available.
is there a wiring diagram to wire my new Jacuzzi magnum 1.5 hp pump?
Hi Randy, The motor does has a wiring diagram on the motor label for field wiring instructions.
I've been led to believe by many people That Jacuzzi pool supplies are now obsolete! Some sources say it was sold to another provider. How are you able to supply replacements, or were you over stocked? Is it advisable to go from a 1hp to a 1.5hp Thanx much
Hello, The company, Carvin, is the only authorized manufacturer of Jacuzzi products. They are currently operating, supplying parts and products globally. We have an excellent blog post, "Can I Go With A Higher Horsepower Pump?", available on our website that will answer all of your questions on upgrading you current pool pump.
I currently have a 15 year old Jacuzzi 15UMF-S Magnum and I was wondering should i go back with the Jacuzzi Magnum or is it worth the extra money to get the Hayward Super Pump? The only reason I am looking around is because my local Pool Place wants almost 600 dollars for a 1.5hp Hayward Pump and that doesn't include install. Thanks!
Hello, Mike. When replacing the Swimming Pool Pump you will need to take into consideration the output Flow Rate of the pump and the Filter's capabilities of the Maximum Flow Rate of total Gallons Per Minute. The Jacuzzi Magnum chart indicates the Jacuzzi Magnum Pump 1 1/2 HP Pump PART# 94027115 will perform at 72GPM to 50' Resistance to Flow. I would best recommend replacing the pump with the Jacuzzi Magnum Pump 1 1/2 HP Pump. Both pump manufacturers offer great quality products, as I do not know any other information regarding your filtration system it is best to replace it with the same pump. If you would prefer to send us more information in about your system, please send an email to email@example.com
Is the Jacuzzi magnum 1.5hp pump the same as an old jacuzzi magnum plus 1.5hp? what is the difference between the two? Your help is appreciated in the purchasing decision.
Hi Mike, The difference between the Magnum and the Magnum Plus is that the Magnum Plus uses full rate motors and the Magnum uses Up Rate motors.
Hi, just bought a house with an in-ground pool. The pump is not working. The model is a Jacuzzi Magnum Plus 1UMP-S order no: 94026770. Do you have a replacement motor or what pump is compatible if I decide to replace the whole unit. Thanks in advance.
Hi Michelle, if you would like to replace the motor, you'll need the A.O. Smith 1 HP Round Flange Up Rate Motor (UST1102) and the Jacuzzi Magnum Tune Up Kit (GOKIT14). If you decide to replace the entire pump then the Jacuzzi Magnum Pump 1 HP Pump will be the correct replacement.
How do you change it to 110 volt?
If you are wiring for 115V, the three wires to the pool pump will be black, white and green. Attach the white wire to terminal 1 of Line 1 (L1). Attach the black wire to terminal 3 of Line 2 (L2). Attach the green wire under the Ground screw (GND). The black plug is shifted in position so the the black wire is attached to terminal 4 Line 2 (L2) and the white wire is attached to terminal 5. Note: in this position the white arrow on top of the 2 prong black plug is pointing at the 115V label.
We have a Jacuzzi Magnum pump with a Magnatek Century Centurion motor with part # 8-184948-21, HP?, Type CX, Volts: 230/115, AMP3: 3?.0/14.0 HZ:60, RPM:3450, TIME: CONT, CODE L, ENCL:DP FR: X56J. FO?:KJM, PH: 1, SERIAL: BP1-158 1081 POOL PUMP DUTYMOUNT HORIZ WITHVENT HOLES DOWN We are looking to replace the motor but cannot find information about a comparable one on the internet. Can you give us any insight as to what specs we need to look for to replace this motor
Jennifer,The cross reference for motor # 8-184948-21 is part # 5221ax on our site.
What pump do I need to replace a jacuzzi model S15LR-S
Hi Dave, The Jacuzzi S15LR-S 1-1/2 Hp 115/230v, No Cord (94027810) will be the correct replacement.
need to cross refrence a new pool pump. I need to replace a Magnetek Magnum Plus 15UMP-S order # 94026788
Hi Hans, The Jacuzzi Magnum Pump 1 1/2 HP Pump can replace your Magnum Plus 15Ump-S pump.
I see the pump comes with quick connect fittings. My plumbing is 1.5 inch PVC. Are they for 1.5 or 2 inch PVC?
they will be 2inch but you can put a reducer to make them 1.5 in
Hello I need to replace the strainer pot in Jacuzzi Magnum Force pump built 1/02/03. It has a 9" basket. What part should I order?
The correct Magnum Force Housing will beour part number 5064- 052.
How to install a new pump?
Our guide on "How to Replace a Pool Pump" will help explain the installation process.
How to drain the swimming pool?
Check out our guide on "How to Drain an Inground Pool".
I am replacing a Jacuzzi 15UMF-S Jacuzzi Magnum Force Pump. The order number matches your part number 94027115. Your pump is a Magnum not a Magnum Force. Is the Magnum Force no longer available?
Teyy, The Magnum and Magnum Force are the same model pump. The name has changed.
Is the Jacuzzi Magnum 94027115 115 or 230 volt?
The Jacuzzi Magnum 94027115 is dual voltage. The pump would arrive set on 230 volt but it can be easily changed to 115 in the field.
(5 out of 5 stars) SPa jet pump for condo
Reviewed By: Jim H. from Daytona Beach,FL ()
Pros: Quiet,easy install and small footprint
Cons: Getting the lid off basket
Powerful pump with a small footprint and very quiet we got it to replace spa jet pump for a condo association so it done well with all the on off on again from the owners come with it's own unions for a easy install out of are 4 pumps it is on cannot tell it is on, The only thing I'm not happy with is the lid to the basket. But little time figure it out.
(5 out of 5 stars) Very Satisfied
Reviewed By: Scott F. from Milwaukee Metro Area ()
Pros: Self Priming, Strainer Check Valve and air bleed off tube, quiet operation
Ordering was simple, delivery was quick and on time. Installed as a replacement for a 15+ Year old Jacuzzi Magnum that never missed a beat. The old pump was not winterized correctly otherwise I am sure it would have kept on going, no fault of the pump. I particularly like the way that the new strainer is designed with the check valve and the bleeder tube. Also the unit is for the most part self priming, unlike its older and now dead brother that I unfortunately killed myself.
(5 out of 5 stars) Exactly what I was hoping for...
Reviewed By: Robert S. from Troy, MI ()
Pros: Affordable, easy to install, works well
Cons: Pump comes with a separate plastic part to support the back, which should not be separate. Not a huge concern, and only "con" to this product.
I never shopped INYOPools before, so I want to comment on both the company and the pump. My first experience with this company was excellent. The new pool pump arrived in a timely manner, worked perfectly, and was easy to install. I upgraded from a 1hp to 1.5hp of the same brand and was pleased with the noticeable difference it made in my filtration system. I highly recommend this company, and the product.