Tune Up Kit Sta-Rite P4E & P4EA Max-E-Glas II / DuraGlas II - GOKIT38

$38.75

IN STOCK
FREE SHIPPING

Part # GOKIT38

By Aladdin

  4.67 Average  

Details

Top

Part # GOKIT38

Alternate Part #'s 65038, GO KIT 38, PL1038, 90-249-3038, ALDGO-KIT38, APCK1033, SPG-601-5038

Product Description

Standard tune up kit for the Sta-Rite P4E & P4EA Max-E-Glas II / DuraGlas II pumps includes the shaft seal and all o-rings, gaskets and lubricant.

We highly recommend replacing the shaft seal, o-rings and gaskets when replacing your motor.  If you use your old shaft seal, it will not mate up properly with the new motor and may leak.

This Tune Up Kit Works on These Pumps:

  • All Sta-Rite Dura-Glas II & Max-E-Glas II 1/2 HP - 3 HP single and dual speed models.
  • All Sta-Rite P4R & P4E Series Pumps 1/2 HP - 3 HP single and dual speed models.
  • Note: Sta-Rite Dura-Glas and Max-E-Glas pumps use GOKIT6

Tune Up Kit Includes:

  • Motor Shaft Seal -(PS201)
  • Seal Plate Housing O-Ring
  • Diffuser O-Ring
  • Lid O-Ring
  • Lubricant

For More Pool Pump Motors

Top

?     Asked on 10/11/2022by David

Looking for the correct tune up kit for the following pumps Sta-rite Dura-glas II - Model 800564 Sta-rite Dura-glas II - Model 5P4R6H Photos attached Thanks so much David

 Reply

A  Answered on 10/11/2022 by InyoPools Product Specialist Hector F.

Hello David, this is the correct tune up kit for the Sta-Rite Duraglass II pool pump series. 
 Reply


?     Asked on 5/10/2022by Inyo Visitor

Hello, I was looking for the tune up kit once i replace my motor. The only numbers i could find were on the housing which are 17307-0010 and 17307-0010W. The pump that is attached is a Century B2848. The bearings went out after just a couple of years, any advice is greatly appreciated! Thanks!
 Reply

A  Answered on 5/10/2022 by InyoPools Product Specialist Craig C.

Hello.  The part numbers 17307-0010 and 17307-0010W cross-reference to the Sta-Rite Max-E-Pro Pump.   The Tune Up Kit Sta-Rite Max-E-Pro (Pre February 2015) - GOKIT79 contains the necessary seals and gasket to complete the motor replacement.    Please complete a visual comparison between the current pump and the Sta-Rite Max-E-Pro Pump exploded parts diagram.
 Reply


?     Asked on 7/13/2021by al marks

i have a K48L2PA105 dura glas pump. what tune up kit do i need?
 Reply

A  Answered on 7/13/2021 by InyoPools Product Specialist Robert M.

The Dura-Glas (not Dura-Glas II) model would use part number GOKIT54. It is designed for Dura-Glas models manufactured since 1998, but it will work on older models if you remove the cone from the seal plate.
 Reply


?     Asked on 4/13/2021by frederick knerr

i have a 3/4 hp Sta-Rite pump.Model No._ 2RA50-220L The best I can make out.Need a Tune Up kit. Does it include the basket lid cover seal?
 Reply

A  Answered on 4/19/2021 by InyoPools Product Specialist Matt S.

The necessary gasket kit for the Sta-Rite Dura-Glas and Max-E-Glas is the GOKIT54 
 Reply


?     Asked on 10/27/2020by George McLaughlin

How long should the motor shaft seal last?
 Reply

A  Answered on 11/9/2020 by InyoPools Product Specialist Megan C.

Hi George, the life of the shaft seal will vary depending on the pool chemistry, correct water levels in the pool, and pump maintenance. 
 Reply

  • Commented on 11/9/2020 by Product Owner

    I bought mine in May of 2020 and it went bad in August 2020.
     Reply

    • Commented on 11/10/2020 by InyoPools Product Specialist Megan C.

      The shaft seal can fail due to insufficient water levels ran through the pump, improper water chemistry, and if the seal plate & impeller on the pump are at 10+ years of age (hairline cracks on them too). They need to be replaced every 10-years along with the diffuser and impeller ring (not all pumps have impeller rings). Even simply mishandling the ceramic seal can cause failure almost immediately. We offer How to Replace a Shaft Seal https://www.youtube.com/watch?v=Moy34mj_7To&feature=em-subs_digest If you prefer you can replace the pump shaft seal and internal o-rings once per year as preventative maintenance, think of it as an oil charge for the car, except, you protecting the motor on the pump.
       Reply


?     Asked on 7/31/2020by Tony Spencer

What is correct motor and rebuild kit for a Sta Rite P4RA6E-186L? Thanks. Tony
 Reply

A  Answered on 10/26/2020 by InyoPools Product Specialist Hector F.

Hi Tony, often times these motors have been replaced from the original complete pump so to be sure, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
 Reply


?     Asked on 7/28/2020by Inyo Visitor

I have found two different versions of this in my searches. One is a the GO-KIT38V (which appears to be for salt water pools) and another labeled GO-KIT38-9 (which I assume is for non salt water pools. Can anyone confirm this, and also, can anyone confirm what version this one is as it is only listed as GO-KIT38 without the additional designation?
 Reply

A  Answered on 10/27/2020 by InyoPools Product Specialist Hector F.

Hello, this kit is for a standard chlorine swimming pool, Unfortunately, we do not carry the GOKIT38V however the only difference will be the saltwater heady duty shaft seal which is part number 5250-235
 Reply


?     Asked on 6/24/2020by dale rozman

Not sure witch ( go kit ) this pump uses I added some photos / only found one part number / any help is appreciated

 Reply

A  Answered on 11/11/2020 by InyoPools Product Specialist Hector F.

Hi Dale, the seal kit for your Sta-Rite Dura Glas/Max E Glas pool pump series is the GOKIT54. Be sure to remove the copper cone insert if you have one in the seal plate so that the shaft seal will fit. 
 Reply


?     Asked on 12/7/2019by Karen Dorriety

Will this kit fit on an AO Smith USQ1102 1 HP pump motor?
 Reply

A  Answered on 12/9/2019 by InyoPools Product Specialist Steve M.

Karen, I apologize, however the seals are specific to the pump side versus the motor portion. What is the brand and model number of the pump that your motor mounts to? 
 Reply


?     Asked on 11/29/2019by Inyo Visitor

I have a Sta-Rite P4E6E-1871 code1A02S. What is the correct Tune-Up Kit?
 Reply

A  Answered on 12/2/2019 by InyoPools Product Specialist Lennox H.

Hi. Yes, this is the correct kit for your model pump. 
 Reply


?     Asked on 9/16/2019by Matthew Hory

I have a sta rite P6E6E-206L code 034H0. Is this the correct tune up kit? Running a 2HP motor
 Reply

A  Answered on 9/17/2019 by InyoPools Product Specialist Hector F.

The correct tune-up kit will actually be the GOKIT79
 Reply


?     Asked on 5/18/2019by Greg Bronson

I have a SQ1152 motor on a pump I can't identify can you tell by the picture what it is? I checked the motor and it works fine but when I have it connected it wont pump water from the pool to use for my water fall feature.

 Reply

A  Answered on 5/18/2019 by InyoPools Product Specialist Lennox H.

Hi, Greg. You have the Sta-Rite Max-E-Glas or Dura-Glas pump which required Tune Up Kit - GOKIT6 (Pre-1998 or w/ Seal Insert) or GOKIT54 (Post-1998 w/o Seal Insert).
 Reply


?     Asked on 9/29/2018by I need the Shaft seal (37400-0027S),Does this tune up Kit has it?

Does The Motor Shaft Seal (PS-201 ) Same as: Shaft Seal (37400-0027S) ? What is the Shaft Seal (PS-201) Dimensions? The Shaft Seal (37400-0027S) Dimensions: 0.825" X 1.4". My pool pump : AO Smith USQ1252, 2.5 HP ,Housing Model: P4EAA6G-189L, what Is the correct impeller for our? I need a new Shaft Seal. Does this Tune Up Kit will works for our pool pump? Thanks!
 Reply

A  Answered on 10/6/2018 by InyoPools Product Specialist Lennox H.

Hi. The PS-201 and 37400-0027S Shaft Seal are interchangeable and the is included with this tune up kit. 
 Reply


?     Asked on 9/20/2018by Joe

Does this tuneup kit fit the AO Smith SQ1102. 1 HP, FR 48Y, SF 1.65 pump (C48L2PA105C4)?
 Reply

A  Answered on 9/21/2018 by InyoPools Product Specialist Lennox H.

Hi, Joe. We're unable to use the motor info to identify the pump's tune up kit. You will need to locate the pump housing model or name. 
 Reply


?     Asked on 5/29/2018by Inyo Visitor

Is this the correct kit for the Max-E-Pro 2HP pump?
 Reply

A  Answered on 5/29/2018 by InyoPools Product Specialist Hector F.

No, the actual correct gokit for your model pump is the GOKIT79
 Reply


?     Asked on 2/17/2018by Gary

Can I get this kit (GOKIT38) with this Shaft Seal PS-201V, 3/4" Shaft Size (PS-201V-CMS)? I am replacing the motor with A.O. Smith 1 H.P Square Flange Up Rate Motor - USQ1102 and have a saltwater pool and would like the extra protection. Thanks
 Reply

A  Answered on 2/19/2018 by InyoPools Product Specialist Hector F.

We, unfortunately, do not carry the saltwater kit version of that seal kit so the saltwater main seal would have to be purchased separately. 
 Reply


?     Asked on 11/6/2017by Jim martin

my stayright pool pump mpra6c-207L motor needs replaced. What motor do you recommend ? Do I need the tune up kit also?
 Reply

A  Answered on 11/6/2017 by InyoPools Product Specialist Lennox H.

Hi, Jim. The MPRA6G-207L model pump will use the USQ1202 motor. There is not a tune up kit available for that pump so you will have to purchase the seal and o-ring separately which are all listed on the Sta-Rite Dyna Pro/ Dyna Pro E Pump Parts Diagram page. 
 Reply


?     Asked on 10/15/2014by Guest

My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
 Reply

A  Answered on 10/15/2014 by InyoPools Product Specialist Patrick P.

The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
 Reply


?     Asked on 2/13/2012by Guest

I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
 Reply

A  Answered on 2/13/2012 by InyoPools Product Specialist Patrick P.

You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
 Reply


Top
Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Nut Drivers, Socket Set, Wrench Set

The pump was leaking throug and into the motor

Written on 6/24/2021 by Guest

Disassembled the pump and motor. Removed the diffuser and "O" ring-diffuser, and replaced O" ring;
Removed the impeller and shaft seal and replaced shaft seals and O" rings;
Removed the Seal Plate and water slinger and replaced slinger and O" rings;
Reassembled back the pump and motor.
Ran the filter and pump without any leaks

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.67  out of 5 stars)
18 Rating
5 star:
 
(14)
4 star:
 
(3)
3 star:
 
(0)
2 star:
 
(1)
1 star:
 
(0)

The Most Recent Reviews