Part # 4715
Alternate Part #'s 25913-154-000, JDY4715
Jandy NeverLube 4715 Three Port Valve 1-1/2" - 2" Positive Seal is designed and engineered to be totally maintenance-free. They're easy to install and easy to use. We use the best materials and best design for the ultimate combination of structural integrity and hydraulic flow.
Jandy 3-Way Neverlube Valve
DO YOU CARRY A NEVER LUBE JANDY VALVE WHERE THE MEASUREMENT INSIDE IS 2" FROM SIDE TO SIDE AND
1 1/2 INCH FOR THE ONE VALVE GOING TO THE WATER DISCHARGE OUT LINE??
PLEASE ADVISE
Reply
Hi Vic. Currently, all of the 3-way valves we stock have the same sized ports on all sides. This generic version of the Never Lube valve 3 Way Valve 1 1/2 Inside / 2 Outside 25913-154-000 - 4715 has ports that accept 1-1/2" pipe (glues to the inside of the port) or 2" pipe (which glues to the outside of the port). It is identical to the Never Lube valves and all parts are interchangeable.
Reply
Jandy 4715; Will a 2" pipe go directly onto the ports, or is a coupler needed? I find conflicting information. Thanks.
I have a Jandy valve now that has two 1.5 in, and a 1.5 into the pump. I want to replace it so I have a 2" pipe going into the pump.
Reply
A 2" pvc pipe would slip over the ports of this valve. A 1.5" pipe would slip into the ports. No coupler is needed for 1.5" or 2" pipe.
Reply
Hello, wondering can I use this diverter on a sump pump discharge line. Im trying to install a valve to divert the discharge of water from sump well during winter from outside the home to a stationary tub in basement. thanks
Reply
Hi, Sam. Yes, you can.
Reply
My Jandy 3 way valve leaks - is it most likely the O ring inside? My never lube valve has a #20 imprinted on the top edge - can you tell me which size it is?Watched the video to replace the guts of the valve - what is the item number for the replacement parts? Lastly my aqua pure chlorinator malfunctioned. The multi-prong plug literally melted away. Do you know what caused this. Can I replace the parts and wires myself or is it a difficult fix? Thank you.
Reply
Hi, Sam. You can use the Jandy Tune Up Kit (GOKIT72) to resolve the issue of the leaking valve. As for the AquaPure system, if the PCB send the incorrect voltage through the cable it can cause the cable to melt. The cable can be easily replaced if the prongs on the cell is bad then you will have to replace the entire cell.
Reply
Can these valves (4715) be reconfigured so that the "common" port is one of the sides of the tee rather than the bottom of the tee?
Reply
Dan, Yes it can. You'll have to remove the handle and adjust the diverter.
Reply
Can this valve be turned off so no water flows out?
Reply
Hello Bob,Yes, you can completely close one of the three ports. The handle on the valve has "Off" molded into the plastic, the location it is facing confirms that the port is closed off.
Reply
Just to be clear...We close off either one of the other two ports, correct?
Reply
I have this valve installed at my pump. I have a lot of air coming out of the pool jets and it doesn't stop. If I rotate the valve to vacuum and back to skimmer, it clears the air immediately. Do you have any suggestions?
Reply
I would recommend checking the gaskets/o-rings on the valve and pump housing. They may be letting air into the system.
Reply
Why do the Jandy valves list ID and OD for each valve?
Reply
Each Jandy valve is designed to connect to two different size pipes. For example on a valve shown with ID 1 1/2" and OD 2", a 1 1/2" pipe can be glued inside the port or a 2" pipe can be glued on the outside of the port.
Reply
I just bought a house with a pool. i'v never had a pool so my question is when the pump comes on automaticaly (it has a timer)what position is the jandy valve supposed to be turned to the main drain or skimmer?
Reply
You can turn the valve so that all the suction is going to the drain at the bottom of the pool, this will suck any dirt or debris on the bottom of the pool through the drain and clean through the filter. If you turn the valve so the suction is going to the skimmer then you will be pulling any leaves or debris off the surface of the pool. You can also set the valve in a half way position so you are pulling from both the skimmer and main drain. I hope this helps.
Reply
The Most Recent Reviews
(5 out of 5 stars) Highly recommended
Reviewed By: Inyo Customer ()
As advertised
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Pamela G. from online ()
Thank you for your online chat. It really helps.
Was this review helpful to you?
(5 out of 5 stars) Exactly what I was looking for
Reviewed By: KRISTY D. from Virginia ()
Pros: Same name brand as the one I had
Cons: none
Part was exactly what I needed. Chat helped me find it in just minutes.
Was this review helpful to you?
(5 out of 5 stars) Great Service
Reviewed By: Ron E. from Madison, AL ()
Pros: fat service, rightproduct
The Valves Arrived Extremely Fast. I Would Recommend Unhappily ToAnyoneForPollParts.
Was this review helpful to you?
(5 out of 5 stars) hands down best pool valve in the bussniess
Reviewed By: Joe L. from media pa ()
Hands down best pool valve by far
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Richard M. from Clarksville, AR ()
This was purchased to replace the same valve that had been in place for 15 years. I consider this good service
Was this review helpful to you?
(5 out of 5 stars) excellent multipostion valve
Reviewed By: WILLIAM K. from LA VERNE, CA ()
Pros: MULTISIZED PORTS AND EASY DISASSEMBLY
Cons: FINDING THE PROPER GLUE FOR A PVC/CPVC JOINT
THE VALVES ARE EXACTLY AS DESCRIBED AND THE MOVEMENT IS SMOOTH. THEY ARE EASILY DISASSEMBLED FOR INSTALLATION OR REPAIR.
Was this review helpful to you?
(5 out of 5 stars) Solid as a rock
Reviewed By: James V. from lambertville, MI ()
Pros: heavy duty, great quality
These valves are really heavy duty. Was very impressed with quality. The handles are probably not as heavy duty as the rest of the unit, but still acceptable. I'm just a pool-owner, so I don't work with these all the time - The one thing I struggled with was confirming that these valves actually do take either 1&1/2 or 2-inch pipe. (1&1/2 goes inside and 2-inch goes outside). They should make that clearer. I didn't want to buy them until I was sure how they worked.
Was this review helpful to you?
(5 out of 5 stars) great valve
Reviewed By: Christopher M. from North Babylon, NY ()
Pros: Very easy to turn
Cons: None
Used Hayward valves for years. Always difficult to turn. The Jandy valve is far superior.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: bbry3 from Titusville, FL ()
Pros: Great
Cons: None
I have 4 other valves and they work execelent. This will be an addition, worryfree valves. Keep up the good products.
Was this review helpful to you?
(5 out of 5 stars) 3 way valve
Reviewed By: JeffV from Indio, CA ()
Pros: Lifetime Guarentee
Well made and works as promised, easy to install and use.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Walter N. ()
Very high quality..Well worth the price
Was this review helpful to you?
5 0
(5 out of 5 stars) Jandy Valve
Reviewed By: Krazydoc from Anthony, NM ()
Pros: Eaxctly as described
Cons: None
I needed a replacement for some internal parts and the Inyo Pool price for the ENTIRE valve was less than the total for the indiidual parts!
Was this review helpful to you?
1 0
(5 out of 5 stars) Quality 3 way valve
Reviewed By: Jason from Jason, Claremont, NH ()
Pros: smooth operation, tight seals
Cons: price
This Jandy valve was easy to install and operate. the seals seem very tight and leak free, also the handle turns smoothly with little effort. this valve combined with the goldline 24V actuator was a winning combo for me.
Was this review helpful to you?