$184.99

Qty:

By Pentair Pool Products


Details

Top

Part # 4600-2506

Manufacturer Code 262506

Dimensions 10" x 6-1/2"

Alternate Part #'s 26-110-1218, 26-2506, 262506, 272526, PAC-06-248, PAC06248, PEN262506

Product Description

Pentair valve with 6-1/2" flange used on the following sand filters:

  • Sand Dollar
  • Tagelus
  • Meteor
  • Sta-Rite Crystal-Flo II
  • Muskin FS683B
  • Please note: the original stainless steel clamp is discontinued and has been replaced by the plastic clamp.

Generic Valve -PL0700

Product Specifications

Plumbing Size:
1 1/2 in.
Valve Location:
Top Mount
Valve Type:
Multiport
Used On:
Sand Filters Sta-Rite Cristal Flo II, Pentair Tagelus, Sand Dollar and Meteor
Top

?     Asked on 1/23/2012by Guest

How do I bleed air with a Tagelus multiport valve?
 Reply

A  Answered on 1/23/2012 by InyoPools Product Specialist Patrick P.

Tagelus multiport valves before 1993 did not have an air bleeder valve and had to self-purge the air through the return lines. If your valve is 1993 or after, there is an air bleeder valve towards the bottom of the valve next to the lower port - about the size of a quarter. Turn knob counter-clockwise to release air.
 Reply


?     Asked on 1/23/2013by Guest

Will this valve fit on a Purex Triton Tagelus filter?
 Reply

A  Answered on 1/23/2013 by InyoPools Product Specialist Patrick P.

Yes, the 262506 valve will fit he Pentair/Purex Tagelus as long as your existing valve is the clamp on style.
 Reply


?     Asked on 1/23/2015by Hernan

Does this valve fit in a PAC-FAB Model TA 35D?? Can I have access to a diagram??
 Reply

A  Answered on 1/23/2015 by InyoPools Product Specialist Alex V.

Herman, Yes, the 4600-2506 is one of several valves that will fit. We do have a  Pentair Tagelus Parts Page.
 Reply


?     Asked on 5/19/2015by Inyo Visitor

I have a Tagelus-Dynamo model TA40 Will this modle fit mine It's a 24 round
 Reply

A  Answered on 5/19/2015 by InyoPools Product Specialist Patrick P.

You will need to look at the Tagelus Valve Options at the Top of This Page. First you will need to determine if your valve is clamp on or screw on, if it is clamp on then your choice would be this valve. If you have a screw on valve you would then need to determine if your filter is from prior to Nov. 1991 or after Nov. 1991. You can also determine this based on if you have V Threads on the Valve or Buttress Threads on the valve.
 Reply


?     Asked on 5/23/2015by john

looking for tangelus deluxe sand filterfiberglass part number 272526 complete valve assembly 1/12 pipe serial 05180881001605 size e different part no. now I guess
 Reply

A  Answered on 5/23/2015 by InyoPools Product Specialist Patrick P.

Hi Joh, this would be the correct replacement valve for the 272526 valve assembly on a Tagelus Deluxe sand filter.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Nut Drivers

1     0

Valve old and worn out. Leaking everywhere.

Written on 4/26/2021 by Guest

Removed all pipes from old valve. Removed old valve. Pre fitted new valve for correct positioning. Secured valve with split ring. Removed old thread tape. Applied new thread tape. Installed piping to new valve. Installed gauge using thread tape. Checked pipes. Stated pump. Checked for leaks

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers

2     1

6 Position Valve was leaking at handle. Replacement valve was a near match.

Written on 7/24/2019 by Guest

Removed clamp that holds valve in place. Wiggle it until old valve came free. Lubed all connecting fittings and o-ring on new valve, positioned the valve, and pushed firmly into place.

You can tell when you have valve in place because the clamp will not fit until you have new valve positioned properly. Tighten clamp with screws provided making sure you get nuts in recess on clamp. Reconnected the plumbing with unions removed from the old valve. Open vent turn pump on and close vent. Check for leaks. Job is now complete..

Were these instructions helpful? 
 

Difficulty

Est. Repair Time

1 to 2 hrs

Tools Needed

Screwdriver, Pliers

0     3

Replacing Top Mount

Written on 4/4/2019 by Guest

I removed the old top mount, placed the new top mount on the PVC pipe in my filter, attached and secured the collar and finally attached all other PVC pipes.

Were these instructions helpful? 
 

Top

Review Summary

 (Average 4.96  out of 5 stars)
22 Rating
5 star:
 
(21)
4 star:
 
(1)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Helpful Review


The Most Recent Reviews