I am looking for a pressure gauge that fits a Hayward Sand Master Filter System (SM1700T or SM1900T.) Also can you recommended the amount and type of replacement sand?
Reply
This would be the correct pressure gauge for the Hayward Sand Master Filter System. The sand you would need is #20 Silica sand also called Pool Filter Sand, the amount of sand you would require would be dependent on if you have the SM1700T or SM1900T the label on your filter tank should have one of the model #'s notched out. If you have the SM1700T you require 100 lbs. of sand and the SM1900T requires 150 lbs. of sand. We also carry all of the parts for the Hayward Sand Master filter system
Reply
What should this pressure gauge 101d-204d read?
Reply
These pressure gauges run different pressures based on the specifications of the system but in general a pressure gauge can run anywhere from 5 psi up to 20 psi. The higher the pressure typically means there is something to be trouble shot in the system. If the gauge does not read anything when the pool pump is running, or is damaged then it needs to be replaced.
Reply
This says bottom mount, but mine mounts to the side. Any problem?
Reply
The term " bottom mount " simply means that the threaded part is on the bottom. If mounted to a side connection, it"s face will simply point straight up. If you wish for the face to point out, you would need a rear mounted pressure gauge. Either will work.
Reply
Will this fit s310s 500lb Hayward sand filter?
Reply
If you have the multiport that came with the filter ( either a SP0710X62 or SP0715X62 ) then yes, this would be the correct gauge for this application.
Reply
I have a Super Flow 100 lb. Canister Sand Filter and the Model is a PF-35. The part # for the pressure gauge used to be 15-2047. I also have a bottom gauge which I need to replace, which I cannot find a part # for. So I would need to gauges, would this one fit? Thanks Doug.
Reply
Hi Doug, Yes this would be the proper gauge for your PF-35 sand filter and should work for both of the gauges you need to replace.
Reply
WHAT SIZE THREADS ARE PRESSURE GAUGE THREADS THEY ARE NOT 1/4 OR 3/8 PIPE THREADS ARE THEY 9/16-18 THREADS FILTER TYPE HAYWARD S166T POOL FILTER
Reply
Rob, The thread size of these pressure gauge is 1/4 NPT. This Bottom Mount Pressure Gauge 0-60 1/4" NPT will replace your current pressure gauge on your Hayward S166T Sand Filter.
Reply
i have s flowmaster 5000 filter where can I get the plastic fitting the brass pressure gauge screws into
Reply
Hi Don, we show that the pressure gauge for the Anthony Flowmaster 5000 screws into this Anthony Flowmaster Brass Pressure Gauge Tee. This fitting is shown as key #21 in the Anthony Flowmaster 5000 Parts Diagram.
Reply
Why do they call it bottom mount? when in reality it gets mounted on the side of the multi port valve.
Reply
It is called a " bottom mount " because if you look at the gauge like a clock, the threaded part that " mounts " into the filter is at the six o'clock position or the " bottom " of the gauge / clock.
Reply
What is the normal reading
Reply
The "normal reading" for a pool varies greatly from pool to pool due to equipment and plumbing packages. But, most pools should clock-in at 10 and 15 psi during during normal operation.
Reply
I'm trying to combine a bottom mount gauge with a relief valve for a tc 300 ,what should i order
Reply
Hi, This Pressure gauge will work with the Air Bleed Tee for the Jacuzzi Tri-Clops TC-300.
Reply
My 0-60 pressure gauge is defective on my Hayward sand filter. I have a 0-100 pressure gauge that fits. Will it be sufficient?
Reply
Hi Jim, You 0-100 gauge can work if the thread size is the same. You filter only has a max operating pressure of 50 PSI so no need to use a gauge that goes to a 100.
Reply
Will this fit the S270T model?
Reply
Hello Phil- Yes the Bottom Mount Pressure Gauge 0-60 1/4" NPT (101D-204D) 4726-0 will fit your Hayward S270T.
Reply
my original guage simply rusted out within a year or so. Will this guage rust easily? Pool is salt water.
Reply
Hi, Chris. This pressure gauge does have a stainless steel trim which can rust over time. However, we have not had any complaints wih this part rusting.
Reply
Hi. My filter is the model S-190T EXP, the little cristal piece is broken, the one that is next to the Generic Bottom Preassure Gauge. How can I replace it, and where can I buy it if I am from Mexico City?
Reply
Hi. My filter is the model S-190T EXP, the little cristal piece is broken, the one that is next to this piece. Where can I buy it if I am in Mexico City?
Reply
Does this pressure gauge fit a Haywood S180T ? I couldn't find my model in the listing.
Reply
Hi will this pressure gauge fit a clear water high rate sand filter by waterway, 22 " diameter. serial no.80800422708 ?
Reply
I have a PAC-FAB PF50. If it's not too much trouble, I'd like a parts list for:
main O-ring (22in)
silicone for O-ring
bleeder valve below bottom-mount gauge
All laterals
Sand needed
I'm getting a lot of sand in my pool so it looks like I have a bad lateral or two. Since I have to open it up I thought I'd do a rebuild as the bleeder is rusty, the O-ring was hard to seal last time I opened it and the sand is about five years old.
You can view the parts diagram for the Pac Fab PF Stainless Sand and see the parts listing beneath it.
Reply
Will this gauge work on Nautilus NS 36 tank?
Reply
Will this pressure gauge work for a waterway millenium model# SD-10-2N11CB?
Reply
This gauge compatibility will actually be based on the filter or valve model that it is attached to.
Reply
It is Millenium Ultimate Granular Filtration but I don’t see a model number for it.
Reply
Hi Mary, could you post a few photos of your filter and gauge as well as photo of the label on the filter tank? Just click the reply link below to upload your photos. Once we get this information we can make the appropriate suggestion.
Reply
Photos added.
Hi Mary, Thank you for the photos yes this pressure gauge is the proper pressure gauge for the Waterway Millennium Sand Filter
Reply
Thank you! Can you also point me to the right O ring for the same tank?
Reply
Hi Mary, If you need the o-ring that goes between the Valve and the Filter Tank then you will need this Tank O-Ring if you are needing the Spider Gasket which goes on the inside of the valve then you will require this Waterway Spider Gasket w/ Diverter
Reply
Hayward "Micro Clear" de-3600, compatible? seems to be a difference vs. de-3600. Same?
Reply
Have Hayward vari-flow XL valve model numberSP0714G11M- what pressure gauge do I need to replace my old one?
Reply
Hi Carol, this is the correct replacement pressure gauge for your Hayward Vari-Flo XL model SP0714G11M multiport valve.
Reply
will this work for a sta rite T 200BP1 sand filter?
Reply
Hi Jean, We don't have confirmation that this pressure gauge will work on your filter. Here is the original pressure gauge that came with your filter and which we recommend - Sta-Rite Replacement Pressure Gauge
Reply
Is this gauge compatible with the Sta-Rite PXC75?
Reply
Hello. The Bottom Mount Pressure Gauge 101D-204D is compatible with the Sta-Rite Posi-Clear Filter PXC75. Please be certain to wrap the gauge threads with Teflon tape prior to installation for a proper seal.
Reply
