Diffuser - C1-200PA

$35.99

IN STOCK
FREE SHIPPING

Part # 5056-10C

By Val-Pak Products

  5 Average  

Details

Top

Part # 5056-10C

Manufacturer Code C1-200PA

Dimensions 6.5" O.D.

Alternate Part #'s 351021065, C1-200PA, C1200PA, STA1013716, 35-102-1065, PENC1-200PA, STA-101-3716

Product Description

INYO # 5056-10C STA-RITE # C1-200PA

This is a replacement diffuser for Sta-Rite Dura-Glas and Max-E-Glas pumps.  Works with the following models:

Dura-Glas 3/4 - 1.5 HP full rated and 1 - 2 HP uprated
Max-E-Glas 3/4 - 2 HP full rated and 1 - 2.5 HP uprated

Features:

  • 5 vanes on back, each approx 2-5/8" L
  • 5 reinforcing vanes on front
  • 5 screw holes on front
  • Inlet with brass sleeve

Dimensions:

  • 6-1/2" O.D.
  • 9/16" thick (from face to back of van at outside edge)
  • 1-7/8" (from back of vanes to front of intake)
  • 1-7/8" inlet I.D.
  • 2-1/4" inlet O.D.

Related Parts (sold separately):

5056-11 Diffuser O-ring

5056-22 Diffuser mounting screw (5 required)

5056-23 Screw Lock Washer (5 required)

Top

?     Asked on 6/28/2019by Caleb

Just want to make sure this is the correct diffuser for this pump. From what I see it is but would like to confirm before ordering. Thanks!

 Reply

A  Answered on 6/28/2019 by InyoPools Product Specialist Lennox H.

Hi, Caleb. This is the correct Diffuser for your model pump. 
 Reply

  • Commented on 6/28/2019 by Product Owner

    Thank you!
     Reply


?     Asked on 3/19/2019by Dallas Williams

Sorry for so many questions. From the my pump # in the pic., which diffuser would I need to get? Mine had a lot build up, or corrosion on it. Or, is it something that can be cleaned up and reused?

 Reply

A  Answered on 3/19/2019 by InyoPools Product Specialist Lennox H.

Hi, Dallas. This Diffuser - C1-200PA is the correct replacement. I'll recommend that you replace it. 
 Reply

  • Commented on 3/19/2019 by Product Owner

    Thanks again!
     Reply


?     Asked on 3/19/2019by Dallas Williams

Sorry for so many questions. From the my pump # in the pic., which diffuser would I need to get? Mine had a lot build up, or corrosion on it. Or, is it something that can be cleaned up and reused?
 Reply

A  Answered on 3/19/2019 by InyoPools Product Specialist Lennox H.

Hi, Dallas. This Diffuser - C1-200PA is the correct replacement. I'll recommend that you replace it.
 Reply


?     Asked on 1/23/2017by Joe greer

My diffuser has several small cracks in the inter circle of the unit but the washe is still tightly in place. I'm replacing the motor do I need a new diffuser? Order 704406
 Reply

A  Answered on 1/24/2017 by InyoPools Product Specialist Hector F.

It is possible that the diffuser will still work okay but if the cracks pass completely through the plastic then I would advise to replace it. Also since it may just be the beginning stages of wear and getting brittle then I would advise to replace the diffuser.
 Reply


?     Asked on 9/19/2016by Joe greer

My diffuser has several small cracks in the inter circle of the unit but the washe is still tightly in place. I'm replacing the motor do I need a new diffuser? Order 704406
 Reply

A  Answered on 10/3/2016 by InyoPools Product Specialist Stacey M.

Hello Joe, I would replace your diffuser if you start to see cracks like that with Diffuser, C1-271p1 Sta-rite (c1-271p1) part 5055-12.
 Reply


?     Asked on 1/24/2015by doug

i need an impellar for my sta rite( one and a half) hp pump.I am unable to read the part number on the impellar. However the part number on the diffuser is c1-200pa could you match an impellar for me by knowing only the diffuser part number. Please let me know if possible since I would like to order this part. Thanking you.
 Reply

A  Answered on 1/26/2015 by InyoPools Product Specialist Robert M.

Hello Doug - The impeller should be part number 5056-09D. Here is a link to view the measurements. This should help you verify the impeller.
 Reply


Top
Difficulty

Est. Repair Time

Less than 1 hr

Tools Needed

Screwdriver, Pliers, Socket Set, Adjustable Wrench

0     1

bushing was leaking

Written on 7/3/2018 by Guest

Turn power off. Take pump apart housing apart and then just unscrew part . Then TIP HOUSING ON SIDE SO GASKET STAYS IN PLACE PUT YOUR HOUSING BACK TOGETHER .

Were these instructions helpful? 
 

Top

Review Summary

 (Average 5  out of 5 stars)
9 Rating
5 star:
 
(9)
4 star:
 
(0)
3 star:
 
(0)
2 star:
 
(0)
1 star:
 
(0)

The Most Recent Reviews