Part # 5019-22
Manufacturer Code 319-4100B
Waterway Strainer Lid – Clear, Round, 2-Ear Design
INYO #5019-22 | Waterway #319-3260
✅ OEM-Style Replacement Lid for Multiple Waterway Pump Strainer Housings
The Waterway 319-3260 strainer lid is a clear, round pump lid featuring two side ears and four evenly spaced grip slots on the top for easy removal. It fits a variety of Waterway pump strainer housings and provides a tight, see-through seal to monitor basket fill levels.
Product Features
✅ Clear Round Lid with Grip Slots
➡️ 4 grip slots on top for tool-free access
➡️ See-through design allows visual inspection of basket
✅ Two-Ear Locking Tabs
➡️ One ear on each side for secure fit
➡️ Fits twist-lock style pump housings
✅ Durable Molded Construction
➡️ UV- and chemical-resistant plastic
➡️ Rib-reinforced for strength and durability
Dimensions
| Measurement | Value |
|---|---|
| Outside Diameter | 7-3/4" |
| Maximum Width (Ear to Ear) | 9-1/2" |
| Height | 7/8" |
| Molded Number | 319-3260 (on ear – faint) |
Compatibility
✔️ Used On:
➡️ Multiple Waterway pump strainer housings
➡️ Confirmed fit for models originally using part #319-3260
⚠️ Note: This lid is very similar to Waterway part 5032-39 (SVL Strainer Lid) but is smaller in diameter. Always measure your existing lid and confirm part number to ensure proper fit.
This New Style lid replaces either of these old-style lids.
New Style Lid Old Style Lid version 1 Old Style Lid version 2
I need the oring that fits to this lid, any ideas?
Reply
Hello Richard, I believe the lid you need is the Lid O-ring, 6" 5050-14A.
Reply
I need the strainer housing but the only part # i can find is on the lid. Any idea how I can find out which housing I need as I see there are several different ones. My lid has the part #319-3260. Its a waterway pump by the way
Reply
Seth, This lid can be used on several different Waterway Pumps. If you can send us photos of the housing I can try to locate the correct housing.
Reply
How would i know if my trap is full? Will the water stop flowing into the pool.
Reply
The water will definitely slow down, depending on how full you are talking about. It is better for the motor if water not flowing does not happen. It would put unneeded stress on it and possibility cause the motor to fail prematurely. If you see a decrease in the returning water, please empty the basket as soon as possible.
Reply
This product is no longer available, is there a substitute?
Reply
Hi Roy, We researched this lid and found that the 319-3260 was replaced by the 319-4100 and this lid is a direct replacement. So we have re-activated this product and when placing an order we will ship the new 319-4100 lid which is shown in the photo on this page.
Reply
We have the above ground hi flo pump it is a replacement for the original pump, We are having problems with when I connect the vacuum hose it sucks air. I googled the problem and found finally an answer that fits our issue. They said that the o ring in the filter basket/lid needed replacement and that fixed it. I see this replacement is made a bit sturdier than our lid. Does it also come with the o ring? we have been afraid the lid might break so I thought I should just get the whole lid in case
Reply
Hi Sue, The Waterway Hi-Flo Lid (319-3260) does not come with the Lid O-ring (5050-14A) it is sold separately. You can start with replacing the lid and o-ring to see if that will solve your problem.
Reply
The Most Recent Reviews
(5 out of 5 stars) perfect locking system on the cap
Reviewed By: Johanna H. from clemmons,nc ()
i have a mirana above ground pool that is 8 yrs old. i am starting to replace parts due to the age of pool. some parts are hard to find. this lid is exactly what i was looking for and better than the old one
Was this review helpful to you?