Part # 5056-06
Manufacturer Code 449
Dimensions 10" ID, 1/4"
Alternate Part #'s 30220, 31-358, 320-110, 320110, 35505-0422, 39006000, 92200180, CX900F, O-1082, O-240, U9-228A, U9228, U9228A, 90-423-5449, ALDO-240-0, APCO2082, SPG-601-1133
10 ID o-ring for a number of pool pumps and filters. Black rubber o-ring 1/4" thick.
Frequently Bought with O-rings
Magic Lube O-ring Lubricant 630
Commonly Used On
American Products Ultra-Flow
Hayward StarClear Plus
Martec/Sunfarrel Pool Master
hi, l have a sta rite pump model # P2RA5F-1251 can you provide me with the proper O ring #
I have a STA-RITE pump P4EA6E-150L. It has been leaking and I assume the O-rings need to be replaced. Is there a kit to replace all the O-rings?
I have a Sta Rite pump, model k4812pa105c3. I believe it is leaking from the O ring between the clamp and the motor. Can you provide me with the proper O Ring for this motor? Thanks
Hi, Ken. You will need to know the Sta-Rite housing model or seal plate number in order to locate the correct Housing O-ring. We're unable to use the motor model number.
I have a sta-Rite model F4E68-188L That I need the O ring for it appears flat instead of the oval. What is part number?
I can't find any kind of model number on my pump, but the seal plate O-ring for this pump is square not round. The seal plate is round and the O-ring is a circle but instead of being like a tube, the O-ring fits into a square channel which makes the O-ring itself more like a square tube in a circle shape. Will this O-ring fit my pump?
Is there always an o-ring between the seal plate before you put the clamp back on. I didnt see one but now that i have re-installed the ring it leakes. Im afraid to tighten the metal ring any tighter
Yes, more than likely there is an o-ring at the seal plate. It will just depend on which model pump housing that you have in order to cross reference which o-ring or seal is there. You can call in with that part number or if you cannot locate that housing model then you can email images through our support request page. Also sometimes you may just need to lube that seal.
Hello, I purchased a motor from you and installed into the Max-E-Pro housing, installed the O-Ring U9-228A, but the housing slowly loses water/pressure after I shut it off.
Any idea of what the problem could be? I'm quite sure the basket gasket is fine too.
There are a number of reasons as to why a pump may loose or have difficulty priming. Please review the results when you click here to see if that may assist in troubleshooting. If they do not then you may want to have a technician come to physically inspect your system.
I have a pump AO Smith SQ1202 and need to get an O ring. Will Part #5056-06 O Ring fit this pump?
Thanks in advance, Ruihong
Hi, Ruihong. You will need to provide us with the model of the pump housing, not the motor number in order for us to locate the correct o-rings. If you're unable to locate the model number of the pump you can send photos of the pump to email@example.com.
I have a sta-rite max-e-pro part # p6e6D-205L. It is leaking at the bottom around where the o-ring would be. Does replacing the o-ring usually fix the leak, and is this the right o-ring for my pump?
Hi, Yes, replacing the o-ring will stop the leak if that's what causing it nd this is the correct o-ring.
I have a sta-rite max-e-pro pump and need an o ring-#6? will this be the right one to order? mfg. code #449, 5056-06
Hi Marian, The Seal Plate O-ring (449) will be the correct o-ring for you Max-E-Pro Pump.