From the picture on line it looks as if the impeller and diffuser are a kit with the o-rings. Am I correct on my assumption?
Reply
The 5020-142 is the impeller only. The diffuser and seals would need to be ordered separately.
Reply
I have Jandy 1.0 HP pump and 1.5 HP on my pool and spa.
The 1.0 HP pump has a screaming bearing and is down in pressure and can't purge its air. I pulled the 1.0 HP pump and slid over the 1.5 Pump into its place.
I want to upgrade the 1.0 HP to 1.5 HP by replacing the motor and changing the impeller. The motor is easy but can I just buy 1.5 impeller?
Reply
Hi Steve, The Impeller will include all the items pictured, it is not sold separately. You would also need to confirm if you have a 1.5 Full or Up-Rated motor, the impellers will be sized differently.
Reply
I want to buy Part number 5020-142 and wanted to verify what is included in the kit before placing my order. The picture online for this part number shows multiple items. Can you also verify this is the correct kit for the Jandy Stealth shpf1.5-2.
Reply
Hi Bill, This Impeller Kit (R0445304) is the correct kit for the Jandy SHPF15-2 pump. It includes the impeller, shaft seal, diffuser and the diffuser o-rings.
Reply
Is this the impeller for a Jandy PlusHP 1.5 HP pump? I'm replacing the motor with a B2854 and figured I might as well do the impeller too. And are the diffuser and o-rings separate?
Reply
I have the b129 motor and need a impeller. Which one would it be?
Reply
Hello Gary- We would need to know what pump you have in order to answer the question of which impeller you need. The motor is a part to the pump, but unfortunately does not provide enough information to determine the correct impeller.
Reply
Your picture actually show two different impellers. One looks like mine the other does not. Mine has the mold stamped # A0580903 is this the right replacement?
Reply
I have a Jandy PHPM2.0 2.0HP Pump New Style Ser #R10FA0686 with a AO Smith B2859 Motor. Are the following parts correct: Impeller Kit 5020-142, Shaft Seal 5020-087 and Backplate O-Ring 5020-136?
Reply
Hi, Bob. Yes, all those parts are correct for the PHPM2.0, Ser # R10FA0686.
Reply
Jandy Stealth SHPM2.0 Serial number R10FH1796
Is this set correct for the above listed pump?
Do the seals and o-rings come with this set as shown in the pictures? If not, need part numbers for those as well.
Thanks
Reply
Hi, J.O. Yes, this is the correct Impeller Kit - R0445304 for the SHPM2.0 pump.
Reply
I need to replace the 1.5 HP motor on my SHPF1.5 pool pump and, after disassembling the pump see that I should replace the impeller, shaft seal and other o-ring seals. I want to purchase the impeller but the photos for this item are confusing. It shows two different impellers and in the QA sometimes your product specialist says that this is just the impeller R0445304 and other times your product specialist has written the this kit includes the diffuser kit with bolts and O-rings. Which is it?
Reply
I HAVE JANDY PRO SERIES STEALTH MODEL #SHPM 1.5 SERIAL # U15FL 1689 AND IT HARD TIME KEEPING THE STAINER FILLED WITH WATER SO WILL A NEW IMPELLER & DEFUSER FIX IT ? I THINK THAT THE PART # R0445304 WOULD FIT BUT I DON'T KNOW WHAT SEAL TO GET
Reply
Hi, Fred. Replacing the Impeller Kit - R0445303 for the SHPM1.5 model can fix the issue if the impeller or diffuser is the caused. A suction leak can cause the same issue that you're having. I would recommend ruling that out before replacing the SHPM1.5 Impeller Kit - R0445303.
Reply
I have a Jandy model #SHPF2.0 Serial # JO6FK2743, and I've taken apart the pump and motor due to a vibrating thumping noise that was shaking the pipes, will this cure my problem? The main shaft bearing is smooth
Reply
When you disassembled the pump did you inspect the impeller and did it show signs of being broken? If it was it would cause vibration. Also did the pad the pump sits on shift? Over the winter settling may occur and the entire pump might not be sitting level.
Reply
Sorry but there is no way for us to answer your question "if it will cure your problem"? The kit you refer to does have an alt, part # R0807201 is the impeller & seal plate o-ring, part # R0445400 is the diffuser, part # 35-423-1088 is the shaft seal. Hopefully, this will cure your noise.
Reply
Thanks for the reply, the pad is bolted down and has been in service since 2007, I had all the equipment installed
Reply
I have a Jandy Stealth SHPM 2.0 pump S/N J06FI1393. Can you confirm the original replacement part for Impeller/Diffuser is R0445304? I believe it has been discontinued and would then be replaced by multiple parts including Impeller R0807201, diffuser R0445400. Can you confirm this to be accurate?
Can you also confirm the shaft seal kit is part R0445500?
Thanks
Reply
The information listed in the product description is accurate: Replace with P/N R0807201 - Impeller Kit and R0445400 - Diffuser. The Old Style Shaft Seal - R0445500 is the right shaft seal for that housing's serial number.
Reply
I have a Jandy SHPF 1.5 2 pump and need a diffuser/impeller kit. Your R0445304 is not available. What diffuser/impeller will work?
Reply
These parts are unfortunately no longer available. I would recommend contacting Jandy at 1 (800) 822-7933.
Reply
I have a handy shpf 2.0 (k07fb1695) that has a broken impeller/diffuser.
I believe (but not certain) that the R0445304 is the correct replacement, however it seems to be discontinued.
is the R0445304 the correct replacement for this serial number?
Thank you,
Colin
Reply
I have noticed that the volume of water coming out of the discharge when pumping water out of my pool is way down. Could it be my impeller? If so what other parts would i need when changing out?
Hello Roland. It is possible the impeller would need replacing. In that event, the Impeller Kit R0445400 is correct. Please also check for suction leaks (bubbles coming out of the returns), a clogged impeller, a dirty filter, and/or a valve on the discharge side of the pump that has been altered. These items would affect water flow back to the pool as well.
Reply
Will this be back in stock or has this been discontinued making my pump trash
Reply
Hello Rich. The Jandy Impeller and Diffuser Kit R0445304 has been discontinued by the manufacturer. The parts contained therein, the Impeller Kit R0807201 and Diffuser R0445400 are available as individual items. It is recommended that the motor shaft seal be replaced concurrent with any work completed on the impeller. Jandy Pump Shaft Seal 5/8" - R0479400
Reply
