Part # PL2673
Dimensions 3.6" X 1.9"
Alternate Part #'s 5110-09A, HAY1012048, SP2600B, SPX2600B
This is an Aftermarket Replacement Diffuser For the Hayward® Super Pump™ and not the Hayward® original O.E.M Diffuser.
Diffuser for 3/4 HP - 2.0 HP pumps (Years 1987 and Prior). Used on several Hayward® pumps including the Max-Flo, Super Pump, Power Flo II and Power Flo III as well as Leslie's® Hydramax pump.
Easy Homeowner Installation
Read our How-To-Guide: How To Replace A Pool Pump Diffuser
**Diffuser Gasket not included... Gasket needed is Diffuser Gasket) (O-141)**
Diffuser Gasket can also be found in the Gokit3 and Gokit3Salt
Disclaimer:
All manufacturers’ names, brand names, trademarks, images, symbols, descriptions, and part numbers are used herein for reference purposes only.
will this fit the SP2607X10A? or does the 10A even have such an item?
Reply
Rod, Yes this will work on the Hayward Super Pump.
Reply
Does it come with a diffuser gasket?
Reply
Hi, R. Bull. The Diffuser Gasket (SPX1600-R) is not included with the Diffuser.
Reply
Do you have any instructions about installing this part. I unscrewed everything and replaced the motor. I must have installed it wrong and friction from the spinning motor shredded my Impeller Diffuser and before I buy a replacement, I have to make sure I am not going to screw it up again. Maybe you have a schematic.
Reply
Please click here to view our how to guide video on changing the motor on the Super 2 which is similar to the Super Pump. In this video, you will also see how the impeller, shaft seal, diffuser and even wiring is done. Also click here to view the parts diagram for the Super pump.
Reply
I had the same problem with friction between the impeller and the diffuser, causing them both to be ruined. I noticed in the video there is a ring on the impeller between it in the diffuser. There is not one of these in the video, is this because the super pump does not have one? I hand tightened the impeller, what else could have caused them to become to close and rub ruining both parts? Thanks, Aaron
Reply
The SPX2600B is used for both Super II (uses impeller ring) and Super Pump (does not use impeller ring). The Super II models will use this diffuser for pumps from 1987 and prior 1/2HP-2.0HP. The Super pump models will use it for models 1984-to Present 1/3HP-2.0HP. If the pumps were not manufactured in the date ranges, possibly you have installed the incorrect parts.
Reply
will this fit a 2.0 hp?
Reply
Hi, Scott. This Diffuser is compatible with the 2HP Impeller - SPX2615C.
Reply
The Most Helpful Review
2 0
(5 out of 5 stars)
Reviewed By: Bob L. from Pompton Plains, NJ ()
Pros: perfefect replacement part
Great service from INYOpools - couldn't be more pleased w the fast delivery
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Important parts
Reviewed By: Inyo Customer ()
Just what I needed to rebuild my system. Mine was very etched.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Great replacement good quality
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Exactly what this DIY Guy needed!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Perfect Fit
Was this review helpful to you?
(5 out of 5 stars) WORKS GREAT!
Reviewed By: Inyo Customer ()
WORKS GREAT!
Was this review helpful to you?
(5 out of 5 stars) Identical to the original and no problem replacing the old one
Reviewed By: Inyo Customer ()
Identical to the original and no problem replacing the old one.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Great fittment for my 1.5 hp motor
Was this review helpful to you?