I recently changed my pool motor and gaskets. I made sure to lubricate all the gaskets with vaseline. A few days later water is leaking from the pump. What did I do wrong? Help please!!
Reply
You never want to use vaseline on any rubber gaskets or o-rings. Vaseline is petroleum based and will deteriorate the rubber quickly. Whenever you change the motor on a pool pump it is recommended that you replace the gaskets and shaft seal as well. A >Go-kit contains the shaft seal, packet of non-petroleum based lubricant and gaskets you will need for your pump. If you already have the gaskets, you can purchase >Magic Lube.
Reply
My pump is not priming even after cleaning impeller. Will purchasing this kit aid in fixing that problem?
Reply
The seal kit can help with loss of prime. I can't guarantee that it will solve your problem. The loss of prime could be from an air leak at the valves or plumbing in front of the pump.
Reply
I am looking for a seal kit for a Sta-Rite PE5D-124L pump. This pump has the copper insert that the seal sits in. Thanks Rit
Reply
Rit,If you have the PE5D-124L with the copper insert, the GOKIT6 would be the right kit.
Reply
How can I tell if the pump is pre 1998 if model number is not visible?
Reply
I am sorry, but the only way to tell is if your pump has this ( J32 ) insert or not. The pre-98 have it in place, the post-98 do not. The cone became unnecessary so Sta-rite made it no longer needed. The best solution is to order the Post-98 Go Kit and if you find you have the cone, simply remove it.
Reply
I am looking for a seal kit for a ste-rite A5F-125L.
Reply
Hi Wayne - Most likely you have a P2RA5F-125L pump which would be a Sta-Rite Dura Glas Pump. Here is the Dura Glas Seal kit for pre 1998 and here is the Dura Glas Seal kit for after 1998.
Reply
I am looking for a seal kit for Sta-Rite pump PE 5E-125 that is pre-1998. The guy that takes care of the pool said he thought the seal was a PS200. Is this Gokit 25 the correct kit?
Reply
Is the included shaft seal ps-100, ps-200, or ps-201?
I am looking for one for the motor A.O. Smith Centurion B8241.
If not compatible, which one I should choose? PS-100, PS-200, or PS-201?
Thanks,
Reply
Hi Chin, The Sta Rite Dura Glas & Max E Glas Pump Pre 1998 Tune Up Kit includes the PSR100 seal.
Reply
Hi. I have a Sta-rite pump model number P6R6G3-208. What would be the correct go-kit to replace my gaskets and shaft seal?
Thank you.
Reply
My Sta-Rite P2RA5E-124L this afternoon suddenly dropped its pump pressure from 11 PSI to 2 PSI. It is still pumping water but the volume is way down, a few air bubbles are present at the pool returns, all suction baskets have been cleaned and the sand filter backlashed. The pump sound is different but the motor seems fine. have owed his pool fro 38 years and have never seen this happen. What is your best guess as to the problem?
Reply
Sounds like you have an air leak somewhere Larry.
Reply
Looking at replacing my motor. It is a Marathone Electric Model C1245 1HP.(year 2012)
The pump is OEM and installed in 1988. Sta-Rite Duro-Glas/Max-E. So the seal kit is the -6. Question now. I have a salt pool so would I need a more durable seal ?
Thanks for the help.
Reply
I have a max e glas pe pump with ser number 8B87 and don't know wich seal kit I need.
Reply
Hello, if you have a Sta-Rite Dura-Glas and Max-E-Glas model P2R this is the GOKIT6 you need pre 1998 and if you have 98-present GOKIT54.
Reply
I have a max e glas pump mode PE XD 124UL. I think it's a pre 98, and has a copper cone seal piece, do I need to order a new one with the kit? the J3-2? Thanks!
Reply
Good morning Scot, Yes your right, and if you are replacing the motor. I recommend replacing the seal and all o-rings.
Reply
I have a Sta Rite pump 5E-125L. It has a copper cone What is the seal kit for it.
Reply
Hi. If you have the Sta-Rite Dura-Glas & Max-E-Glas pump with the copper seal insert then this is the correct tune up kit. However, with a partial model number I can not confirm if this is the correct kit.
Reply
I have a Max E Pro Pump P6RA6G-207L
Which go kit please?
Reply
Hi, Robert. The Sta-Rite Max-E-Pro Tune Up Kit - GOKIT79 is the kit for the P6RA6G-207L pump.
Reply
I have a stay-rite max-e-glas pump model # PEXYD-133L will this kit work for it ?
Reply
I've got a pool pump motor = Franklin P/N 1103675400 (2HP 220V). The pump housing has C03-137P on it. The Diffuser has a part number CI-200PA stamped on it. I'm not sure about the flow rate of this pump as I cannot see the P/N stamped on the impeller. I'm told that this is a Dura-Glas and it was installed in 1985. Not sure of model number (decal missing).
With the clues above, can you please tell me the GPM of this pump? Also, I would like to verify tune up kit is GOKIT6.
Thanks!
Reply
Hi, Craig. Unfortunately, we do not have the proper info needed to calculate the flow rate of your pump you have. You would need to calculate the feet of head of your pool using the steps in our How To Size a Pool Pump. Once you've calculated the feet of head of your pool you can use the performance curve on the Dura-Glas & Dura-Glas II Brochure key # D to determine the flow rate. I would recommend getting the 1998-Present Tune Up Kit GOKIT54 because it can be used with the pre-1998 by removing the seal insert.
Reply
Ordered the Century USQ1072 3/4 hp with square flange. which kit do I need to order for gasket, etc. replacement.
Thanks
Reply
Hello Bunk- The seals are based of your model pump not motor. What is the model of your pump?
Reply
I have a sta-rite duraglas P2RA5E-181L 1 HP pump that I will be replacing the motor. Which GOKIT please?
Reply
If you have the cone that is in between the seal plate and impeller then you go with the GOKIT6, if you do not have the cone you go with the GOKIT54.
Reply
Starbright SBP-100 fwl Low suction from pool. Filer.pump stored in a heated basement each winter. Originally purchased in 2004. Motor seems to running as it has in past years BUT Suction is not very strong this season. The filter basket front end of the pump was clogged with leaves in basket. Cleaned basket and checked hoses for additional debris. Suction is low ? Debris in impeller?
Reply
Hi, Francis. Debris in the impeller can lead to low water flow, also a clogged or dirty filter can lead to a reduced suction and water flow.
Reply
How can you tell if you have a pre-1998 pump. My pool was installed in 1996 and the pump was replaced on to three years later.
Reply
Hi Joe, Please watch our Video on How to Determine if You have a Pre 1998 or Post 1998 Sta Rite Pump. It goes into great detail on this topic.
Reply
hi ..i just bought a pool pump motor order number 770270..i want the tune up kit
how do i tell if i have pre 1998 unit ??
Reply
Hi, Alvaro. You only ordered the motor, there is no way to tell what tune up kit you'll need from the motor. You will need to provide the pump housing model # and serial number.
Reply
how do you find the date code?
Reply
Hi. Only if you have the original serial number you'll be able to confirm. However, you can also inspect the pump's seal for a Seal Insert - J3-2-50. If there is one you'll need to purchase GOKIT6 (Pre-1998) if there is not one then purchase GOKIT54 (Post-1998).
Reply
I would like to replace my pump motor (only) type B USQ1102, ser. 24113CH 1 hp. Which seal kit will I need to go with it? Also, is there an equivalent model which might offer better performance (greater suction, quieter, longer lasting, etc) which is worth the added cost to purchase?
Reply
We are unable to identify the tune-up kit by the motor model number. We will need the model number from the service tag on the pump housing. The pump housing is the part that the motor is mounted to by bolts or a clamp. If you need further assistance with locating the model number, you may email pictures of the pump to upload@inyopools.com The energy efficient single speed upgrade to the USQ1102 is the Energy Efficient A.O. Smith 1 H.P Square Flange Up Rate Motor - UQC1102 If you are able to wire in at 208-230 Volt you may be interested in the 1.65 HP Variable Speed Pool Pump Motor Square Flange - ECM16SQU
Reply
Will this pre- 1998 tune-up kit work on pump number P2RA5YF-125L? Thanks
Reply
Hi, Ray. It can if you have the Seal Insert should in the Sta-Rite Dura-Glas and Max-E-Glas Parts Diagram. If you do not have one, then you will need GOKIT54.
Reply
It looks like either tune up kit will fit the P2R series pumps, it this right that either kit will work?
Reply
I'm replacing the motor on my Sta Rite Max-E-Glas pump Model number PE 5D-124L. I found an extact motor replacement and need to get all the gaskets and seals. For this model which Kit would I need? Also does this come with everything I need gasket and seal wise to include the lube for the gaskets?
Hello, Can you please send a side view picture of the entire pump?
Reply
I'm trying to distinguish what go kit I need for my pump, but I cannot make out what model I have. Any help would be much appreciated!
Hi, You will require the Sta-Rite Dura Glas Tune-Up Kit. The Dura Glas has 2 tune-up kits one here which is the Dura Glas Tune Up Kit before 1998 and another one here which is the Dura Glas Tune Up Kit after 1998. We put together a Video on How to Determine if your Dura Glas Pump is before or after 1998 which should help you determine the proper tune-up kit you need.
Reply
my pump is a star-e-glas model PE50 but dont know how old they are (before 1998 or after ??).
can you help me figured out which kit will work ??
it runs 2hp motor
I include pump picture and label and motor
thanks
Denis fromm Quebec,Canada
Hi, Denis. To determine which seal kit you'll need, you will need to confirm if there is a Seal Insert in the center of the Seal Plate as shown as KEY # 7 on the Sta-Rite Dura-Glas and Max-E-Glas Parts Diagram. If you do not have one, purchase GOKIT54.
Reply
I have a Sta Rite Dura Glass pump P2R that's not pumping water through the filter. The motor is working as it should. The pump filter is clean and in place. I have my valve set to pull water from the skimmer, negative. Why ?
Reply
Hi, Elgin. Several factors can prevent a pump from priming. You can check out our How To Determine Why a Pool Pump Won't Prime guide to determine the cause and fix the problem.
Reply
Hello. I am trying to determine which rebuild kit to order for our pump. The pump sticker shows Model Number P2RA5F-125L. Not sure when the pump was new, as we bought the house last year. Any help would be great.
Thanks!
Reply
Hi Dave, Based on the year your pump was manufactured You will need this Sta-Rite Seal Kit Pre 1998 or this Sta-Rite Seal Kit 1998 and After. If you are not sure if your pump is from before or after 1998, then we put together this Video on How to Determine if your Sta-Rite Pump is Before or After 1998.
Reply
I have StaRite model P2RA5E-124L code 1F96T. Do I need the pre or post 1998 kit?
Reply
I have a hot tube with a MAX E GLASS pump and the Pump model is a PEXD - 124UL.
The tube is a Hot Springs I/O from about 1986 and I need the tune up kit.
What is the kit # required?
Reply
Hello,
I have an old 1987 Hot Springs Home Spa Model H with a model 1LC-UN2 Jacuzzi pump and a 1 hp, 120v, 1 speed, GE motor. I have a leak at the shaft seal and was looking to purchase a kit to replace all the seals. Any idea which kit i should order?
I would love to purchase a replacement pump/motor assembly but cannot find a replacement! If you have this information too that would be great!
Hi, Hanan. You have the Jacuzzi Model LC Series Pump, replacement parts are currently available.
Reply
Can I use a ps-200 seal and leave off the copper insert, on a pre-1998 DuraMax P2R pump?
Reply
Hi Steve, we do not show Duramax pool pump however the P2R is Duraglas. For the Duragass series, the PSR200 shaft seal is used on the newer generation models without the copper cone. The pre 98 series will use the PSR100 seal that uses the copper cone. Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I have an original sta-rite pump with a failing Marathon imPower motor. Since the Marathon motor is now discontinued, I am considering the V-Green 1.65 HP Square Flange 48Y Variable Speed Motor - ECM16SQU. If it makes sense to continue to use the existing sta-rite pump, I want to do a tune-up when I replace the motor. I need to confirm which kit. Picture attached. Thanks
Hi. I think I have a pre-1998 pump but am not sure. Would you kindly look at the attached pics and advise whether I should be ordering the pre 98 GOKIT along with the PSR100 seal that uses the copper cone. Thanks!
Hi Lawrence, so in order to confirm the date of manufacture, you will either need to know the serial number of the pump or by seeing if the original seal plate has a cone insert where the shaft seal is installed. When in doubt, purchase the GOKIT54 which is the newer kit, and simply remove that cone insert in the seal plate.
Reply
The Sta-rite pump is 1996. So which seal a nd kit do I need?
Reply
Hello Darale. In order to identify the correct seal kit just a bit more information may be required. If the pump is a Sta-rite Dura-Glas or Sta-Rite Max-E-Glas manufactured in 1996, the GOKIT6 is compatible. The GOKIT54 can also be used by simply removing the copper cone insert from the seal plate. At times, working with the copper cone insert can be problematic. If you are unsure of the pump model please send a few photos of your pump and motor. Please take a close-up of the motor label and a wide photo of the complete pump including the pipes going in and out of the pump. Once received we can make the proper recommendation. Tune Up Kit Sta-Rite Dura-Glas & Max-E-Glas Pump Pre 1998 - GOKIT6 Tune Up Kit Sta-Rite Dura-Glas & Max-E-Glas Pump 1998 To Present - GOKIT54
Reply
The pump is 1996. The motor is newer as it was replaced a few years ago.
If the copper cone is still in the seal plate, GOKIT6 would be correct. However, there is a chance it was removed when the motor was replaced last time. My suggestion would be to get the GOKIT54. The GOKIT54 will work if there isn't a copper cone and if there is a copper cone, you can remove the cone and still use the shaft seal from the GOKIT54.
Reply
Hi. I believe I have a pre-1998 Sta-Rite pump (however, I'm not sure). I have attached a few pics. Can you guide me as to what GOKIT I will need? For reference, I'm replacing the AO Smith motor K48K2PA101 with a Century QC1072. Thank you!
Hello Tommy. The GOKIT6 contains the appropriate parts for new motor installations on the Sta-Rite Max-E-Glas Pre 1998 pool pump.
Reply
Hello. I have need of the seals etc for my old hot tub pump. The table information is as follows:
STA-RITE. NPS4492
Motor K48K2PA101
AO Smith
The motor shaft diameter is the same and all other parts I see here appear to be identical. If you can help confirm I am getting the right items, it would be appreciated.
Reply
Hi Lola, the shaft seals are specific to the pumps and not the motors, and I can't find a cross-reference for the numbers you provided. Please send us pictures of your pump and any labels on it to upload@inyopools.com so we can be sure to recommend exactly what you need.
Reply
