Can you replace single speed pump motor with dual speed pump motor?
Reply
Yes but you can't go with a higher HP than the single speed motor. For example if you have a 1 HP single speed you cannot go with a 1.5 HP dual speed motor; you would be able to use a 1 HP dual speed motor. Customer would need to purchase a toggle switch or timer to switch from high speed to low speed.
Reply
I'm trying to find a replacement motor for my pool pump but my model number doesn't match what you have listed as the model number. My model number begins with a C48 and yours begins with an SP. Please help.
Reply
What we have listed on our chart pages is the pump model number. The model number you have will just identify the motor. If you look on the plastic housing on the pump there should be a sticker which will have the pump model number. You can usually find this by the discharge port on the pump. Once you locate it you can choose the correct replacement motor. Be certain to change the shaft seal and gaskets as needed. You can use our >How to guide if you need help.
Reply
I need to get a spa motor for our hottub, its BN37V1, and I also need a pump, but having a hard time finding one. Do you have any pumps to go with the motor? And what is the cost. I will need both.
Thanks
Reply
Hi Joe, Yes the AquaFlo Spa Pump has the BN37 Motor this would be the complete spa pump and motor.
Reply
I am in the market for a capacitor for the Magnetek Century a/c motor model 7-193077-01. If you could help, I would appreciate it. thanks
Reply
This motor runs extremely hot in my hot tub. can you explain if this is normal. very hot to the touch.
Reply
Hello, The motors will run hot to the touch. If the thermal overload does not shut the motor off, it is within normal operating temperature.
Reply
i need to replace a Magnetek Century Electric laser xl spa motor. the P/N # is: SP 1510-Z-2-4XLE
the part # is: 9-1-73632-02
HP 1.0 / .16, SF 1.00, RPM 3450 / 1725 , FR Y48Y , 115 volts, 10.3 / 3.1 amps, PH 1
Can you tell me which moter would be best replacement. My motor is about 11 3/4" long and won't fit if longer. thanks
Reply
Hi, The 1 HP 2 Speed 115V Thru-Bolt Motor (BN37) would be the correct replacement motor.
Reply
I have a manga tech motor in my jacuzzi that has part number 7-177782-03. Can you tell me the replacement motor I need with this info?
Thanks, Mike
Reply
I need to replace a Hayward Magnitek Dual Power 1 Hp Motor 115V Serial Number BN9-29. What should I be looking at?
Reply
We would need to know the part or catalog number from the motor label to ID the correct motor.
Reply
I need to replace a Proline SKP712.2 above ground 2 speed pump motor. The model # is PE71-III-H. It is an Emerson motor with a model # of C55CXKEF-4876. It doesn't give me the HP, but I expect it to be 1 HP. Its. 115 volt 2 speed. MFG #ME08C and is a 48Y frame motor. 16.0/4.8 amps. Do you have something that will cross to this?
Reply
Hi George, Based on your amp draw you will need this BN50 1.5 HP Dual Speed 115V Replacement Motor I would also suggest replacing your shaft seal when you replace your motor and you would need the Proline PE71 Shaft Seal
Reply
Need new motor/pump assembly for 24' round 52" pool. Old pump is Waterway, 2HP, 2-speed, Hi Flo SD 1502189245. We always run it on high to move 30 GPM in 8 hours. Low doesn't cut it; barely moves the water. We want our next model to be timer compatible. Looking at Hayward Power Flo Matrix. Need a pump with horizontal fixture. Is 2HP too much? Thinking dual speed, 1.5HP would be better. We got the 2HP our local store had on shelf. What do you recommend? Which timer do we need to match? Thx :)
Reply
Hi, Laura. A 2HP pump could be too big depending on the size of your filter.
Reply
I have a jacuzzi above ground pool filter unit with Magnetek 7-186654-01 1 HP 2 speed motor. When I searched on this model number, the present site came up but I don't see my model number listed. Would the BN37 be the correct replacement?
Reply
Hi Phil, Yes this BN37 motor is the correct replacement motor for your Magnetek 7-186654-01 1 HP 2 speed motor.
Reply
We have a model number LEA-30 pump and would like to know what motor fits it
Reply
Hello Mary - The BN37 will work if you have a thru-bolt style 48Y frame 1HP 2-speed 115v motor. Check the specifications on your current motor to see if these match.
Reply
I ordered a BN37 pump and impeller turns counter clock wise. How do I wire it to turn Clockwise? I have a 3 wire power cord Green,White & Black The lable states:
Ground
# 1 High Speed I attached White Wire to # 1
# 5 Common I attached Black Wire to # 5
# 6 Low Speed No Wire attached
This now turnes Counter Clockwise. How do I change to Clockwise?
Thanks so much for your help.
Reply
Hi, Robert. These motor can not be wired for a reverse rotation, it will only rotate in a counterclockwise rotation.
Reply
I have a Jacuzi/Magnetec motor 7-181326-01, 2-speed, 1 HP (I think, 115V motor that I want to replace. Is the BN37 the correct replacement?
Reply
I have a 1.5 hp 2 spd pump 115 v, 60 hz, 12.0/3.1 amps p/n 7-181327-03. What would a correct replacement be?
Reply
Can BN37V1 2sp 1hp replace Sta-rite ABG4E7-2A4SP through bolt. Im in Calif. Can a 1.5 hp 2sp, 115v in BN37
also replace stay-rite ?
Reply
Hi there, I have a Hayward power flo II SP1515-Z-24-e 1.5 hp dual speed 3450/1725. Looking for a replacement motor, what I don't see is the shaft length in the descriptions. My shaft length is 2.25" from the motor face to the end of the shaft with 3/8-16 thread. what do you recommend?
Reply
Hi. Ben. The shaft length is 2.38".
Reply
Hello I have a 1.4hp motor The switch burned up... I need a wiring diagram to repair power cord to switch and switch to motor please and thank you
Reply
Re: listed pump. How much is it to include the power cord and and off switch already attached to the motor. OR do you have other like motors that come as a complete system?
Reply
Hi, Dave K. Unfortunately, there is not a replacement motor available with a power cord and or switch already attached. These parts will have to be purchased separately and then installed on the motor.
Reply
Hello Dave,
I have a BN37 1.5 hp, RPM 3450/1725 AMP 11.0/2.9 part #7-177782.03, Frame R48Y. Apparently this model is discontinued. If possible I would like to g to a 2HP without changing any plumbing. 1 1/2 Inlet and outlet FMCP wertend NEW.
Reply
I have a Hayward Power Flo Pump with an A O Smith motor model number C48L2A29 (also has SP-1510-Z24-XE written on the label). Is the BN37V1 the correct odor replacement part?
I have a Hayward SP-1510-Z-2-XE spa pump with a motor Mod S48LA210 - 110v- 11.6/3.3 amp - 1 1/6hp . The motor shaft is pitted and I must frequently change out the mechanical seals. What would be a replacement for this unit?
Reply
I have a Pentair Optiflow pump with a single-speed 115V 1.0hp 48Y (BN25V1) motor. Can I install this two-speed motor with toggle switch 18313301 in its place?
Reply
Are any other parts required to install pump?
Reply
Hi Deborah, could send a few photos... a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
I am looking for a pool pump motor Mod # ST1072. It connects to a pump with 6 bolts.
Reply
Hi David, the correct replacement single speed motor for your motor ST1072 is actually the ST1072. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
believe this is same motor but mine is1 1/2 hp . do you have this in 1 1/2
Reply
Could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
I have a Waterway PH2100-3 pump that I would like to replace the motor on. Can I replace the BN36 with a BN37V1? Attached pictures are my current motor's nameplates.
Hi, Yes you can upgrade your 3/4 HP BN36 motor to this 1 HP BN37 motor. You will need to upgrade your impeller to a 1 HP impeller to take advantage of the higher flow of the 1 HP motor, you will require this 1 HP Waterway Hi-Flo II Impeller. When replacing your motor you will also require this Waterway Hi-Flo II Shaft Seal.
Reply
Why does the sticker on my pump say "1.0 HP - 0.12 SPL"? You said it is 3/4" HP? 8.8 amps at 115V indicate 1.0 HP.
Reply
Waterway uses a SPL HP Rating where a 1 HP is equivalent to a 3/4 HP standard motor. The industry has done away with SPL HP and gone to standard HP ratings. Please be assured this is the correct replacement. If you want to dig into this more we did write this article on Why Your Spa Pump's HP is a Lie which gives more detail.
Reply
I have the pictured below pump , would the century 1.0 be the same to replace motor with? What is the oblong box on top of new pump? I also have a side hook up to filter , can this be turned to meet the set up I have? Thank you
Century 1.0 HP Thru-Bolt 48Y Dual Speed Low Amps Motor - BN37V1
Hello Lou Ann. The Century 1.0 HP Thru-Bolt 48Y Dual Speed Low Amps Motor - BN37V1 is a compatible motor replacement for the Century Motors motor model BN37, 7-177782-03. The motor's capacitor is located underneath the capacitor housing (oblong box). It is recommended that the Closure O-ring (O-108) (154493) - 071422 and Pump Shaft Seal 5/8" - PS-1000 be replaced concurrent with the new motor installation. The side discharge is a function of the pump's wet end and not the orientation of the motor. The BN37V1 is compatible with the Waterway Hi-Flo AG Side Discharge Pump
Reply
Would this be a correct replacement for Hayward Power-Flow LX SP1540Z1B?
Hello Bill, the replacement motor for your motor model s48e48a04 is the BN24V1. We also recommend replacing the seals and gaskets when replacing a pool pump motor. For your Hayward PowerFlo LX pump that will be part numbers 5111-03 and 3262-17. I have also emailed you an estimate connected to your account with us that you can convert to an order if you would like. Items are in stock and ready to ship.
Reply
