My existing top valve model number is 39263009 -DV-ASSY7-POS 1 1/2NPT which needs to be replaced. My tank model number is 94086250 which is fine. They are Jacuzzi.
Thank you
Reply
Bob, Based upon the model # you provided, the correct Jacuzzi replacement valve is part # 26-105-1018
Reply
Hello,
The valve assy. on my jacuzzi filter is leaking and need to replace it. Mine is fastened to the top of the filter canister with a 2 piece band with two clamping screws. #39263020K seems to be the right one, is that correct? It seems to be the only option not bolted down.
Thank you
Reply
Hi Paul, You are correct the Jacuzzi 39263020K valve on this page is the correct valve for the Jacuzzi Laser Clamp style filter.
Reply
the part number I need is 39-2630-20-R this part number has a K at the end, will this still work to replace mine?
Reply
Don, The Dvk-7c Valve, Clamp Type (39263020K) will not work because it is a clamp style and the Valve Dial 7 Position (39262803R) is a bolt style.
Reply
Will this valve replace my model #39263009 for my Laser 190 L filter?
Reply
Hello Gary, this valve will not work for your filter as the 39263009 is a bolt-on style Jacuzzi Laser Filter Valve and the this Jacuzzi 39263020K is for the Jacuzzi Laser Sand Filter Clamp Style. The correct replacement for your filter is the Jacuzzi 7-Way Valve 39262803R
Reply
I have a Jacuzzi sand filter on my swimming pool and I'm losing water through my drain line hose. The filter housing has a 7 position Dial Valve , Model # 39263009. Can you tell me if a bad gasket or O-ring seal would cause this problem. If so would I have to replace the entire valve or are there replacement Gaskets or O-rings that can be purchased separately to repair the existing valve.
Reply
Richard,You are correct in that the spider gasket within your valve may be the culprit causing the loss in water. We sell replacement parts for your valve, so ideally you would not have to replace the entire valve. All of the replacement parts we sell for your valve can be found on this page. The spider gasket is glued into the key assembly, which is the only way you can purchase it.
Reply
I have lazer tank the valve leaks there is a hole at gauge and I get air and water leak.is it a39-2630-20-r it clamps on you cant just buy gauge part thank you and do you have the valve
Reply
Hi Ted, If the valve body and the port for the pressure gauge is good you can replace just the pressure gauge. You can use either the Back Mount Pressure Gauge (102D-204D) or the Bottom Mount Pressure Gauge (101D-204D).
Reply
Hello, does this valve come complete with everything- including the pressure gauge & sight glass? How about the clamp and o-ring to connect?
Reply
Hi Rico, this valve comes with the pressure gauge and o-rings but does not come with the clamp. If you look at the Jacuzzi Laser Parts Diagram you can see that everything within Box #1 is included with the valve.
Reply
hi all i can find is my serial number 055711 can you tell me which valve i need i no its the clamp style thank you
Reply
Hello, we would need to know at least the model number of the filter to determine the correct valve replacement.
Reply
I have the Jacuzzi Flo Pro system SS240 and I need to replace the valve system. Which one do I buy. Do I need to measure the diameter of the unit?
Reply
Hi Cathy, The TM-12-H8, or 27515-154-000 Model valves are the valves that can be used with the Jacuzzi Flo Pro SS240 filter.
Reply
Hi. I am trying to find a spider gasket for a Jacuzzi model #ss240. do you carry this part?
Reply
Hi Erik, I will need to know the model of the valve that you have in order to locate the correct spider gasket.
Reply
I have a Jacuzzi 7 pos DV assy Model # 39-2631-05, clamp type, which is obsolete but it looks like this will work as a replacement. Can you please confirm. It is mounted to a Jacuzzi Laser L192C-7 Filter base. Thanks
Reply
Hi, Brian. This DVK-7C Valve, Clamp Type will fit on the Jacuzzi Laser L192C-7 filter tank.
Reply
I have a jacuzzi laser ll model 192 sand filter with a clamp on valve. Is this the correct replacement valve, mine is a little different looking it is more ball shaped on top. I probably only need a new diverted kit will the dvk6/7 kit work on mine? Considering that the entire valve is not much more $ I would probably consider replacing over rebuilding. Thank you
Reply
Hi, Randy. This DVK-7C Valve, Clamp Type is the correct replacement. It would be more convenient to replace the entire valve that rebuilding it.
Reply
I have a L192C clamp on valve with a split "to pool" connector. I guess I need a new valve, (link please) but wondered if you had a "screw over" link piece for that connector so I don't have to risk damaging a new one by screwing the hose link into it?
Reply
Hi, Richard. The L192C filter valve is p/n 39263020K. You can use the Union - 400-4060 with this valve.
Reply
I have a Jacuzzi Laser filter md# L250c-7c. Is the 39263020k the correct replacement value for my filter?
Reply
Hi, Ronnie. Yes, this DVK-7C Valve - 39263020K is the correct replacement for the L250C-7C filter.
Reply
will this fit a assy 7-POS 1-1/2NPT del/modele 263009
Reply
Hi, Tanya. This clamp style valve will not fit, you will need the Carvin 7-Pos Valve Bolt-On - 39262803R as the replacement.
Reply
Needing a new complete multiport for a jacuzzi L160C sand filter. The info on the multiport says part number 39263105 and DV ASSY 7 POS 11/2"V-FLN it clamps onto the tank. Can you tell me what I need?
Reply
Hi, Amy. This DVK-7C Clamp Style Valve - 39263020K is the correct replacement valve that you'll need for your filter.
Reply
hello, i have a jacuzzi pump and i need to replace the clamp between the spheric filter and the head. the model is dv 2dvk-c7, the diameter of the clamp is 21 cm
do you have it?
thanks
Reply
Hello Michele- The clamp for your Jacuzzi TM filter is Clamp Assembly (85813903).
Reply
If get this part from you and it is the wrong one can I return it???
Reply
Hi, Dott. Yes, you can. The product must be in new or unused condition with all original packaging. Please review our Return Policy.
Reply
Is this complete with all the internal components, or is it just the body or shell? I have a jandy 7 pos. That is cracked where the pressure gauge screws in..
model# 39263105 DV ASSY 7-POS 1.5
need to replace a multi valve system DV assy 7-pos 1-1/2 V-FL model # 39263030 - will this unit work?
Reply
Hi Paul, As long as your valve clamps onto the filter then this is the correct valve for you. If your valve bolts onto your filter then you would need this Jacuzzi 7 Way Bolt on Valve
Reply
I attached a picture of my jacuzzi multiport unit that is leaking from the handle. is is attached by a clamp. It seems to be the correct unit but my unit's model number is 39263030 and your unit is 39263020K. is this the new model number. Just want to be sure before i order the unit and end up with something i cannot send back b/c i opened the package. thank you for your help
Hi Paul, Thanks for the photos those are very helpful! Yes this will be the proper replacement valve for your valve shown in the photos.
Reply
Could you help me identify this model? I'm needing to replace it, and I think this is the correct replacement but am not sure.
Hi Julie, Thank you for the photos! The valve on this page is the correct replacement valve for your Jacuzzi 39263105 valve shown in your photos.
Reply
I have allantic pools by jacuzzi sand filter that leeks I need valve parts could you help me find them
Reply
Hi, Corina. Please provide the tank or valve model number or pictures so that we can identify the valve.
Reply
I have an old sand filter need a new top Mount valve. Filter mode : JACUZZI L192C-7C. What will be the right part number.
The DVK-7C Valve, Clamp Type - 39263020K is the correct replacement valve for your Jacuzzi Laser Clamp Style
Reply
I have a jacuzzi ss240-6 sand filter. Will this fit my filter?
We show that this filter will use this TM-12-H8 Valve
Reply
I have a Jacuzzi SS160-HK6-FP filter and need to replace te clamp on valve. Is this the correct assembly for that filter.
Reply
I have a Jacuzzi Brand Filter - 6 Position Dial -
Laser II-192-6-CP FIL
Will this work as a replacement?
Reply
Yes this would be the correct replacement valve for your Jacuzzi Laser II filter.
Reply
I have a Jacuzzi sand filter and trying find out if this would be the correct top Mount Valve the number 39263105
Hi Kathy, yes this will be the correct multiport valve replacement for your Jacuzzi multiport valve model 39263105.
Reply
Will this work on a Jacuzzi 191L filter? Or replace a Cantar DV Assy 7-pos 1-1/2 V-FL 39263030 valve?
Hi David, this is the correct replacement multiport valve for the Jacuzzi model 39263030 valve.
Reply
Sorry, I'm looking for valve #39263105, is it the same one? Is it the same as or the same as the Carvin valve? I appreciate your help with this question. Thank you
Hi Carlos, yes this is the correct replacement multiport valve for the Carvin valve model 39263105.
Reply
Is this the valve I need to replace mine? I just bought a new diverter kit and the valve was broken in the process. Does the new valve come with o-rings and all?
Yes, this is the correct replacement valve for your Jacuzzi filter and it includes the o-rings.
Reply
I have a 39263105 and I wanted to know is there a specific sand it needs and how much does it take and how often should it be changed.
thanks
Normally you will need to replace your sand every 5-7 years and you will use #20 Silica Sand also called pool sand. Here is a Video on How to Replace your Pool Filter Sand which you may find helpful.
Reply
I have a Jandy SFTM25 sand filter that i need to replace the multiport valve assembly on part number SFTM-MPV it also has a part number of 39263105 on a label on the side of the valve. This number 39263105 is listed on this part as well. If this is a direct replacement for mine will all of the plumbing be in the the same locations so i don't have to change anything. And does this also come with the clamp assembly as well, please advise. Also is this in stock and how long to ship, thank you.
Reply
Hi Gary, Yes this valve is in stock and is a sutiable replacement for your current valve. We cannot guarantee the port locations will be in the exact same spot as they have made a few modifications to these valves over the years. If you want to make sure you dont have to re-plumbing then you may consider going with this Jacuzzi Top Half Assembly which is the top half of the valve and all the guts. The clamp is not included and here is a link the Jandy SFTM25 Replacement Clamp
Reply
Is this just replacing the top handler for model # 39263105??
Reply
The DVK-7C Valve, Clamp Type - 39263020K(Without Valve Body O-Ring) is the top valve to replace the older model#39263105. The DVK7 Complete Cover Kit - 39262605K is the top key cover for the valve itself. Click here to view the parts page for the Jacuzzi 7 Way Dial https://www.inyopools.com/pool_parts_7_way_dial.aspx
Reply
Looking for a rebuild kit for a Jandy L250c-7c filter valve. The value will not switch from backwash regardless of handle position - suggestions? Appreciate the help!
Seth
.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&height=75&width=75&mode=pad)
.jpg?format=jpg&scale=both&anchor=middlecenter&autorotate=true&mode=pad&width=650&height=650 "Jacuzzi Inc. Jacuzzi Carvin DVK-7C Valve, Clamp Type Multiport Valve, 1-1/2\", 7 Position - 39263020K")
Hi Seth, this Diverter Repair Kit DV 6/7 - 39251509K is a good start to rebuild your Jacuzzi 7 Way Dial valve unless you need the handle and cover as well. This DVK7 Complete Cover Kit - 39262605K would get you going again if that is the case.
Reply
I know this is a replacement for the Carvin #39263105. Was wondering if my piping will hook up without having to modify it. Are the hook ups at the same place?
Reply
Hello David, yes this valve is a direct replacement for your Carvin/Jacuzzi alternate valve part number model 39263105. I have also emailed you an estimate that you can covert to an order if you would like. Item is currently in stock with an approximate delivery lead time of 2-5 business days.
Reply
