Part # SP2607X10
Warranty 10 Year Warranty On Strainer Housing, 1 Year Warranty on Motor
The Hayward Super Pump is one of our best-selling pumps. This is a basic, reliable pump for a single body of water. It can be used for an in-ground pool or spa, or as a dedicated pump for a waterfall.
Hayward Super Pump Application:
Add On Options:
Hayward Super Pump Features:
Hayward Super Pump Overall Dimensions
Click here for more Hayward Pool Pumps
can 1 HP super pump be replaced by 2HP model, have a 50,000 gallon pool with DE60 Hayward filter?
Hi. Yes, it can if your system and filter can handle the water flow. Use these following guide to determine, How To Measure Total Dynamic Head With Gauges, How Do I Calculate Feet of Head for My Pool?, How to Size a Pool Pump for Your In-Ground Pool, and How To Size a Pool Filter.
If my voltage to my Hayward superpump is 243 after the timer, is that too much for this 230 motor? Have you ever heard of this being a problem?
Hi, Lisa. That is not too much, the motor can operate at 10% above the rated voltage which is 253. However, it can cause the motor to run hotter/higher amps at the higher voltage and will shorten the life of the motor over time
I have a 17000 - 18000 gallon pool with a sand filter Hayward model S-220T , 52 GPM flow . What size Hayward super pump do I need ?
18x36 inground pool. Purex Nautilus 36 DE filter which will handle 72 gallons per minute. My pool is about 27000 gals. Feet of head is difficult to estimate but I think about 50. Will a Hayward 2607 1 hp meet my needs? A pool tech told me it would. I need an answer ASAP because the pool company will replace with a 2610 1.5 hp if needed. There are no fountains or accessories and just one skimmer. I run my Polaris with a separate booster pump. Thanks
Hi, Gerald. With 50 feet of head using the SP2607X10 pump, your flow rate will be about 50 GPM. This pump will turn over your pool is approximately 9 hours. So it will be sufficient for your pool. The SP2610X15 will also be sufficient with approximately 65 GPM.
Will this Hayward Super Pump SP2607X10 work with your Hayward S244T sand filter or should I go with the 270T ? Replacing a Hayward S200 that's on it's last leg after 20 years of good service.
I have a question about replacing my 1 hp hayward pump with a pureline. Since the pureline has 2" conns., if I use a 2"m X 1 1/2"f reducer bushing, will that change the alignment of the union elbow from the pump to the filter? i still want to use the EC-65 base. Thanks!
Vinny, Using reducers should not affect the alignment of the plumbing. The Pureline Prime and Super Pump housing are similar in dimension. The only difference is the female threaded port size on the pump.
I am going to need to replace my Hayward SP2807X10 pump. Is the Hayward SP2607X10 a comparable pump for a replacement?
Hi Gene, The SP2607X10 a comparable pump for replacing your SP2807X10. However, we would suggest the PL2601 PureLine Prime 1 HP as a replacement, the reason being is that we found the PureLine to be extremely reliable and the price is actually less than the Hayward.
Would this be a match plumbing wise for a Waterway SVL56 1hp pump or would re-plumbing be required?
Hi, FranticGolf. You will need to re-plumb if you switch to the Hayward Super Pump.
will I be able to replace a sta-rite 3/4 hp with this pump with no additional plumbing
Hello, The ports on both pumps do not line up so re-plumbing will be necessary.
Can I buy the electric end with the impeller there is nothing bad with my housing
Hello Mike - Unfortunately, the motor is not sold with the impeller and other parts assembled. You would have to get each item individually and then put it together. You can find all of the available items on the Hayward Super Pump Parts Page.
Can I buy the electric end with the impeller there is nothing bad with my housing
All motor orders come as just the motor. The pump parts have to be assembled to the motor.
If i change from a 1hp to 1.5 hp for 12,000 gal pool, and change from sand to cartridge filter, will it cause a problem?
Hello, As long as the new filter is sized for the higher horsepower pump, you will not have an issue.
After buying this, all i will have to do is take out the existing pump/motor then plumb the new pump/motor in and use the previous wiring?
Tyson, Yes, that is correct, Please note that this is a dual voltage motor and is preset to 230v. If you have 115v, you will need to follow the diagram on the motor to wire it for 115v.
my 1 hp pump died.will any 1 Hayward 1 hp super pump do the trick .my old one is a Hayward super also.
Hi. This Hayward Super Pump 1 HP - SP2607X10 will replace your existing Super Pump.
My pool is 50000 gallons with 120 ft of head i have a 2 hp super pump does this sound like I'm oversized
Hi, Mike. You will need to provide us with the FOH on the suction side and the filter model in order to determine if the 2 HP Super Pump is oversized.
will this pump be a direct replacement for my existing SP1607Z1M?
If this motor is mounted specifically to a Hayward Super Pump then yes this would be the direct replacement. You can also look into the Pureline Prime as a drop in replacement.
What is the replacement Super Pump for the Hayward SP1607Z1M 3/4 Super Pump ? I have had this pump for less than three years and the motor seized up and has to be replaced. I cannot find any replacements models for this motor, in fact when i enter the model number in the compatible model box it tells me that model number is not found. What gives ?
Based on the model number that you have provided this ia a 1 horse power. That Super pump model is SP2607X10. It is possible that you have a 3/4 hp full rated version which is equivalent to this one horse up rated version. Also here is the 3/4 horse power Super pump SP2605X7 but remember that technically this version is a different model hence having less horse power then the model number that you have provided.
I need a power cord for a Hayward sp2607x10 which has a c48k2n143b1 motor. What's the part number? the only power cords I see are the SPX1250WA and SPX1550WA1. Is either of these compatible?
Hi, Larry. If the pump is wired for 115 volts and will plug right into an outlet you can use either power cords depend on whether you have a standard or twist-lock outlet.
how do you remove the pump from the shaft on the motor
If it is a Super Pump then the ceramic part you will wedge out with a flat head screwdriver and the spring part of the shaft seal is pulled off of the impeller. Make sure the little rubber washer gets taken off of the impeller as well otherwise the new shaft seal will not slide on to the impeller all the way and it will leak.
How many GPM is the 1 hp Super Pump?
This pump has a max of 86 GPM. There is a chart on the product page that shows the GPM based on the feet of head if you have additional.
i have an 18 by 36 ft pool 8ft to 4 ft depth. how many hours should i run the pump?
Hi Alan, Rule of thumb is that the pool pump should run one hour for every 10 degrees of the outside temperature. Or you use our How To: Size a Pool Pump guide to calculate the flow rate to determine the run time.
Could you give me the RPM for this Hayward Superpump 1 HP
All single-speed pool pumps should have a motor with 3,450 pumps should have a motor with 3450 RPMs.
I am replacing old pump with a new one .old was 115v connection. MOVEED black pug from 240 to 115 arrow.connected green wire to green terminal. where does the the white wire and then black wire terminate? there is L1 and L2 does it make a difference?
Les, If you are wiring for 115v, as long as you have one wire on line 1 and the other on line 2, it will work. This video may help:https://www.inyopools.com/HowToPage/how_to_wire_a_pool_pump.aspx
I have a 20x40 in ground pool with water jets in the steps. What size pool pump do I need?
I have a 18 x 36 in ground pool, 4 ft deep shallow and 8 ft deep. I have a Hayward cartridge filter and 1 1/2 Hayward pool pump. The pump runs on 220 and the motor seems to be very hot. Can't put my hand on it. I go through a pump every 2 years. Any suggestions!!
Hi Denny, Several things can cause the motor to run hot, you can check out our Pool Motor Troubleshooting blog for more info.
I am replacing the motor on my SP2607X10 pump. I know I need to replace other items as well. Is there a kit with all the seals & gaskets that I need to replace as well?
I am getting ready to install a 14x28 foot in ground pool (around 15,000 gallons). The pump is a 1.5 hp with a flow rate of 88 gpm. I need a flow rate of 32 gpm to filter in 8 hrs. The max flow on my 24" filter is 45 gpm. I have 45 feet of head. Based on that a 1 hp pump would supply 50 gpm. Do I really need the 1.5 hp pump? At 42 feet of head it still pumps at 67 GPM. Isn't that to high?
The 1 HP would work just fine for that size of pool. You definitely need a 1.5 HP though if you start adding features such as, a fountain, a spa, solar heat pump, pool cleaner. Adding any of these features will require more horsepower since the flow rate will be divided up by each addition feature.
A cheaper pool pump I've looked at says it shouldn't be exposed to rain/ weather. Can the Hayward pump be completely exposed to the weather??
Hi Sandy, This pump can be placed outside exposed to the weather, however it will affect the life span of the pump. The less exposed it is the longer it will last.
what is the difference between the single and 2 speed Hayward motor?
Hi Fred, A single speed motor runs at 3450 RPM for the desired run time and a two-speed motor can run at 3450/1725/ RPM for the desired run time.
I have a 15k gallon pool with a 60 sqft Hayward DE filter. Thinking of replacing the pump to cut down on the electric bill. Currently, I have a PAC-FAB Challenger 2HP pump. Seems to me the pump and filter are overkill for the size of the pool. Can I use a lower HP pump on the 60 sqft filter? What pump would you suggest?
Hello Rich, yes you can go with a few different pumps, SP3007X10AZ, or SP3200VSP Offering up to 90% energy cost savings over single-speed pool pump alternatives via an integrated variable-speed drive and totally-enclosed, permanent magnet motor, TriStar VS is an ideal pool upgrade for those looking to reduce energy use and save money.
My current in ground pool has a pump that plugs into a regular outlet. Do your 3/4hp pumps require a 220 line? Also how about if I go up to a 1hp model?
Hello Rick - The 3/4HP and 1HP Hayward Super Pumps are dual voltage (115/230).
I have an old filter wet institute system in my inground swimming pool 24,000 gallons. I would like to replace this old wet institute with the Hayward system How big of a job is this
Hi Jill, the biggest question would be what is the current state of your plumbing, but normally this would be a relatively easy weekend DIY project. We have a good Video on How to Replace a Pool Pump which should give you a better idea of what is involved in this project.
How many gallons of water does a Hayward Super Pump, 1 HP self priming, pump per hour?
Please click here to view the Hayward Super Pump curve.
What is the overall length
Hi Loyd. The overall length of a Hayward Super Pump 1 HP Single Speed is 24".
I have an 18' x 36' in ground pool that is 3' in shallow end of pool and 8' in deep end. I have a Jandy ei salt machine. My flow light will not go off on the salt machine. My current pump is a 1 hp. One of the trouble shooting answers to the Jandy Salt machine says that when the flow light stays on it could be that the pump is not strong enough. Based upon what I have provided do you think I need a 1 1/2 hp pump?
Hi Bo, The very first thing I would do is follow the steps in our guide on How to Correct Low Pool Pressure many times these simple steps will fix your flow issue.
Hello please help,i have unground pool 16/38 and 8 feet down about 24.000 gallons water, also have sand filter 18'' 150 lb sand,which best pump i need to buy???? Thank you.
Hi Lora, As long as this pump will not be powering any water features like waterfalls, solar or spa jets then the 1 HP Hayward Super Pump on this page would be my recommendation.
I need to replace my AO Smith pump C48k2n143b1n, sp-1607-21-m is this the right item?
Yes if you were looking to replace the complete pump which includes the pump housing, basket and motor then this would be the correct pump.
I am thinking on buying a new pump. I have very little to no suction at that skimmer. I have blown the line and it is not plugged. I have replaced all fittings and valves and still not very good suction. The drain one at the bottom of pool works great. Without skimmer working I can't clean pool. I was wondering if a bigger pump would help. I currently have a 1hp.
Lloyd what is the distance of pipe from the pump to the skimmer which is have the bad flow? What is the distance of pipe from the pump to the main drain? Do you know the pipe size for the skimmer line? How about pipe size for the main drain line? What happens when you turn your diverter valve so you shut off the main drain and all of the suction is going to the skimmer?
We are building a pool... So the dimensions are 24 x 10 and 5 feet deep... What's the best pump please
If you do not have any water features likes waterfalls, solar, runs of pipe exceeding 70' or spa jets then I love the 1 HP Hayward Super Pump.
Replacing a Whisperflo WF-26 1.5 hp. Would the SP2607X10 1 hp pump be a good replacement? GPM=45 & Distance to Head=approx. 43' If so, what is the price of the pump with an EE motor?
If you don't need the additional .5hp and the 1/2" of pipe size for the in and outlet, the Hayward 1 HP Single Speed Super Pump will be an option. The Hayward 1 HP Single Super 2 Pump will be the better replacement. Hayward Super 2 EE Pump 1 HP Single Speed
I currently have a 1 HP Pac Fac Pinnacle pump would the 1 HP Hayward Super Pump be a comparable replacement?
Hi Patrick - Yes the Hayward 1 HP Super Pump would be a great replacement for the discontinued 1 HP Pac Fab Pinnacle Pump.
just want to make sure i am ordering the correct item. my current pump as the model number as SP2607X10 and the serial number as 21120805002046020. its labeled as a hayward pool produtcs item. please advised, thank you.
Hello Shawn - The Hayward SP2607X10 is the correct replacement pump.
I have a Hayward SP1607X10. Is that a previous version of sp2607X10? Will parts for one be the same as parts for the other?
You are correct that is the predecessor to the to the sp2607x10. The parts will work for either pump.
How much is the power consumption difference each hour between 1.5 HP and 1 HP pool pump by KW.
A typical 1 HP pump has a power consumption of 1.5 Killowatts per hour (KWH) and a 1.5 HP pump is at about 2.3 KWH
How many hours per day should I run my pump?
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Less than 1 hr
Screwdriver, Socket Set
My old pump was smoking. It was very rusted and I needed to replace the motor. I searched the internet and found the best value with INYO. I had just ordered a new filter (old one cracked when it rains it pours) and was very satisfied with INYOPools service. I took a picture of the wiring before disconnecting the old pump to insure I was able to install the new pump correctly. The new pump was delivered in just 2 days and works great. The screws to remove the back cover of the old pump were rusted and very difficult to remove. I put some grease on the screws of the new pump and covered them with duct tape to avoid this in the future.
(4 out of 5 stars) hayward pump
Reviewed By: pumba from youngstown ohio ()
Pros: great price, durable pump, brand new!
Cons: a little wait for delivery but not bad
mostly i was looking for a better price on a replacement pump for my pool. i save about $150 by ordering from inyopools. i was a bit worried that it might not be what they said, but it was in fact new, in original packaging, durable, warranted, and shipped right to my home
(5 out of 5 stars)
Reviewed By: ()
I have a small in-ground pool with Spa-Jets. After lots of use, the motor finally gave out so I had to replace it. I bought the complete pump and removed the filter housing and just replaced the motor and pump so I didn't have to change or adapt the plumbing. That made the replacement Super Pump Motor super easy. Anyone need the filter housing?
(5 out of 5 stars) Workhorse Pump
Reviewed By: Benjamin R. from Caldwell, NJ ()
I ordered this pump to replace an existing Hayward Super Pump. I had never done any type of pool plumbing but the videos seemed to simplify the whole process. The Super Pump itself worked perfectly fine. One nit. Watch that the drain plug is completely closed. Mine wasn't and I saw what I thought was a good sized leak. Closing it rectified the problem. I installed this pump with two unions to make future pump maintenance easy. One recommendation I would make it is wire the pump before the plumbing. In my case, it was a little difficult getting the wire into the pump housing.