How many hours per day should I run my pump?
Reply
There are many factors to consider; bather load, gallons of water, pump horsepower, type and size of filter just to name a few. A good guideline is 8-10 hours a day. On the cooler days and early and late season, you can cut the run time down to 4-6 hours because there is usually less swimmers and cooler water requires less chemicals. In peak season, when it is the hottest, raising the run time to 10-12 hours per day will help to keep the pool clean and circulating during it’s time of heaviest use.
Reply
how many gal is the flow on pureline pool pump pl1502
Reply
Hi, The flow rate is based on the Feet of Head of the pool. You can view the pump performance curve located in the Product Description of this pump.
Reply
Can this motor be wired for 220V?
Reply
Hi Mark, No this motor cannot be wired 220V. I would suggest the PL1601 1.5 HP Pump if you need the motor to be wired 220V.
Reply
I have an eighteen ft diameter, 4 ft deep above ground pool. Is the volt pattern the same as the haywood? Is this the best one for our pool? Is it better to get 1HP or 1.5HP? Thanks, for your help. Donna Hight
Reply
Hi Donna, This pump would be the same voltage as the Hayward above ground pool pump, this pump is an 115V pump and uses a standard 3-prong plug. For your pool I would suggest the 1.5 HP pump as this will ensure that you have a large enough pump to properly circulate your pool.
Reply
I have a 30 foot Above Ground Pool. My pump motor has gone out. It is a 1 HP but have had some tell me that I need to go at least 1&1/2 HP. Is this what I need to do? I run my pump 24 hours a day during summer months. All so do I need anything more than just the pump?
Reply
Hi Teresa, Yes for a 30' round above ground pool we would suggest a 1.5 HP pump. If you are just looking to replace your pump then this is all you would need. If you are looking for a pump and filter then I would suggest the 1.5 HP Pump with 19" Sand Filter.
Reply
Need to replace my above ground pool pump. Is your pump adaptable to discharge from the side instead of the top to the filter?
Reply
Hi, the discharge port can be rotated so that you have a horizontal discharge. To do this you will need to permanently remove the Pool Pump Mounting Flange Key #15.
Reply
I currently have a jacuzzi 1 1/2 h.p. pump for a 24' round pool. I got the pump second hand and I have no idea of it's age. It has been leaking from the drain plug which is stripped out. It has a different plug from where it goes into the outlet (a.c. plug). Can this pumps plug be adapted to that outlet?
Reply
If you are needing a drain plug for your pump, I need the pump model. If you do not know please attach a picture of the complete pump so I can identify it for you.
Reply
Hi I have a new 21x54 round pool and now the pump died, can I replace it with a 1.5 horse if the old one was 1 horse???
Reply
Hi, Terry. Yes, you can if your filter is large enough to handle the water flow of a 1.5 hp pump.
Reply
Had asked previously if discharge could be changed from vertical to horizontal. (2nd question in Q&A) I was told that the discharge port could be rotated to horizontal. I noticed that the next to last question in the Q&A is answered by saying it could not be rotated. Answer soon please---need to order!
Reply
Hi, Neal. The discharge on this pump can be rotated to a horizontal discharge.
Reply
I have a 24 by 48 above ground pool and my jacuzzi laser sand filter system recently died will this be a good replacement for it pretty much Universal correct?
Reply
Hi Michael, Yes this pump would be sized properly for a 24' round, the ports are not going to line up exactly as your Jacuzzi pump. If your Jacuzzi pump has the discharge coming out of the top and you are using flexible hose from the filter to the pump then this pump should be good for you.
Reply
Is this pool pump quality as good as the Sta-Rite Dynamo 1.5 hp by Pentair? My pool is 33x52 round. Very good price on this pump! I'm very interested in this pump. Thanks
Reply
Hi Robin, In my experience the PureLine Pure Pro XL is every bit as good as the Sta-Rite Dynamo. The plumbing ports on the PureLin are not in the exact same spot so you may have a little re-plumbing.
Reply
I have a oval 18x33 20k gal approx I'm looking to turn over every 6-8 hrs I currently have a Hayward 1 1/2 hp is that size sufficient? I'm looking to replace what I have it doesn't seem to be keeping up
Reply
Hi Joe, You could upgrade to the 2 HP Waterway Above Ground Pool Pump or if you wanted to go with something a bit more powerful you could go with a 1 HP PureLine Prime Inground Pump this would require that you plumb with hard pvc plumbing.
Reply
yes i have and kayak 12+20 pool he an pump hp 1.5 next 185pl can you help me
Reply
Hi. If you're looking for a replacement pump for your pool I will need to know the size of the filter you have.
Reply
I have a 24 x 52 above ground pool with a sand dollar filter (sd-40) I need to replace the pump and sand in the filter. I went to a local store to buy sand and she said if the filter required 150 lbs of said then I need to change the pump from 1 hp to 1 1/2 hp. It says on the tag a design flow rate of 40 gpm. Can you recommend a pump?
Reply
Hi, Joey B. A 150 lb sand filter does not require a 1.5 hp pump, you can use a smaller pump as long as it does not exceed the flow rate of the sand filter. I would recommend staying with a 1 hp pump, the PL1501 would be my recommendation.
Reply
I have a 16 x 32 above ground pool that has a waterway hi-flo 1.5hp pump system w/ a 120 cartridge filter also from waterway. I am looking to replace the pump only and want to move it to a location above the waterline and about 40' from the skimmer. I'll eventually move the skimmer when I replace the liner, but not at the moment so it needs to have a 40'-45' run to the skimmer. I have wiring for both 110 and 220. I am looking at this pump and maybe a VSP. recommendations?
Thanks so much!
Reply
Hello Kevin- We were just speaking and the phone call dropped. As long as you can verify that the filter can accept a minimum of 80 gpm and you do, in fact, have 230v you can use the PureLine Prime Variable Speed Pool Pump 1.65 HP - PL2605.
Reply
Hi i have a sand filterPro 50D from GAME, which pump is a good replacement for this one?
Game: 4710
Model: 72715
Volts: 115V
Hz: 60
Amps: 3.6
HMax: 32.8ft (10M)
QMax: 40gpm (151 L/min)
Reply
will this pump work with 15 ft above ground pool.. 5000 gallon
Reply
Hi. A 1.5 HP Pump is too large for a 5000 gallon pool. I would recommend the VL40T32 or C2251540LSS systems.
Reply
What horse power do I need for a 18*4 above ground pool
Reply
Hi, Cynthia. You can use a 3/4 hp or higher pump depending on where the equipment will be positioned from the pool, filter size, and the additional features that the pump will be used to operate like a heater, pool cleaner etc. If you can provide us with that info we can tell you what size pump you'll need. You can also reference our How To Select Above Ground Pool Pumps Guide.
Reply
The pump I'm replacing is a Hayward 1.5 hp, 70 gpm. Will this pump be a good replacement? I have a 24 foot, 48" above ground.
Reply
Hi Randy, Yes the PureLine PL1502 would be a great replacement for a Hayward 1.5 pool pump being used on a 24' round pool.
Reply
i have a pentair 340210 pool pump 1.5 hp 115v - will your 1.5 HP Above Ground Pool Pump - PL1502 replace the pump i have and does it have an on and off switch on the pump
Reply
I need a pool pump the sta-rite gave out i need 1 1/2 hp pool is 12 ft deep by 36 long would this pump work on my pool
Reply
Hi, Rosa. Unfortunately, this pump will not work for an inground pool. We can help you find a suitable replacement if you can provide the make and model of your Sta-Rite pump.
Reply
I inherited taking care of a pool and I have had a Hayward/ DE pool filter system for 3 years and have struggled with it. From changing the DE, getting the filter opened to clean and guessing how much to add when backwashing. I am looking for possibly something easier for my new 24 x 52 AG pool. Any suggestions? Are replaceable filters any good? Any help is much appreciated!!
Reply
Marsha, Unfortunately, this pump would not work with a Hayward D.E filter because of the discharge location. I would recommend the Hayward Matrix pump.
Reply
I have a stay right pump 1 hp model number DYNN I’m sorry DYNII – and I – one/340197SR I was wondering if this pump would work on mine to replace the old one
Reply
Rick, You will be able to use the pump if you have a sand filer but you will have to replumb. If you are using a hose connections with unions, the unions will not fit this pump.
Reply
I have a Hayward 1.0 hp pump that has gone out my filter hold 150 lbs of sand interested in buying the 1.5 hp will they match up
Reply
Hi. A 1.5 HP Pump will be too larger for a 150 pound sand filter. I would recommend a smaller pump like a 3/4 or 1.
Reply
I currently have a pentair turbo king 1.5hp..1 1/2 " connections..Is this made like the turbo king far as my connections in the same spot going from pump to sand filter and from strainer basket to pool? Just wondering if i would have to redo my plumbing..
Reply
Hi Mel, This pump would be very similar to the Turbo King but the plumbing ports are not in the exact same position. If you are using flexible hoses going to and from the pump then this should be pretty easy. If you are using hard plumbing then you may have some minor re-plumbing to do.
Reply
I have a splash SuperPool will my hose connections work without modifications?
Thanks
Reply
Hi, Steve. If the hoses and plumbing connections for the Splash SuperPool are MPT, then you can use this pump with little to no modifications. If not then you will have to modify your system to use MPT fittings.
Reply
Does this pump have a high, low, and off switch?
Reply
This pump is a single speed so there is no high low switch and there is not an on/off switch either. Plugging these into a current with a switch or a timer is an ideal application.
Reply
Hi I have a 15'x 30' oval 48" deep above ground pool, will this pump work good for it and if so what is a good sand filter to go with it?
Reply
Hi Chad, Yes this would be a great pump for a 15'x 30' oval 48" deep above ground pool. If you wanted a pump and filter then I would suggest the PureLine PL1511 1 HP Pump and Sand Filter System another option if you wanted to purchase the filter separately would be the Hayward S180T Sand Filter.
Reply
Hello,
I have a 42,000 gallon inground pool. The deep end is 10' deep. I want to use the pump as a dedicated vacuum. Should I go with a 1 HP or 1.5 HP pump? Thank you.
Reply
Hi, Thomas, we suggest something like the 1.5 HP PureLine Prime Pump as you will need a self-priming pump. The PL1502 is a gravity fed pump typically used on above ground pools as the water is above the pump meaning that pump does not need to self-prime. However, for inground pools, the pump is normally at the same level or above the pool water and you will need a self-priming pump like the 1.5 HP PureLine Prime Pump.
Reply
Hi, I have a 23,000 gallon pool. My water pump went out last year and I’m purchasing a new one, would this one do the trick?
Reply
Hi Nancy, As long as your pool is an above ground pool then this pump would do the trick for a 23,000 gallon above ground pool.
Reply
I currently have a Hayward Power Flo Matrix 1.5 Hp, 115v, and 15 amp above ground pool pump. Would this be a compatible replacement for my existing pump.
Thanks,
Reply
Hi Megan, Yes this would be the pump we would suggest as a a compatible replacement for your Hayward Power Flo Matrix 1.5 Hp
Reply
Hi, I have an 18x33 above ground pool that is 4ft deep. I currently have a Jacuzzi Hurricane sand filter. The tag reads that the filter area sq ft is 2.64, needs 250lbs of sand, and the filter/backwash rate is 53 gpm. Would the pureline 1 1/2 hp pump work for my pool and current sand filter? Thanks in advance for your help!
Reply
Shannon, While the Pureline PL1502 will work, you may have to replumb if the pump to filter connection uses a special union connection.
Reply
Hello-I currently have an Echo 1.5 HP 60Hz 115 Volts 12 amp with a sand filter for a 18x34'x48" oval pool that needs replaced. Would this pump work as a replacement?
Reply
Hi Joe, Yes this would be a suitable replacement pump for and Echo 1.5 HP pump being used on a 18'x34'x48" above ground pool.
Reply
Is this pool pump compatible with a 15' round above ground pool?
Reply
Yes you could use this on a 15' round pool, you would also be able to get by with a 1 HP PL1501 Pump
Reply
Can you rotate the discharge port. Exiting from top no good for me.Need to rotate. Can you change direction without voiding warranty.
Reply
Hi John, Yes you can rotate the discharge on this pump without voiding the warranty. Here is a Step By Step Guide on How to Rotate the Discharge Port for PL1502 Pump which you may find helpful.
Reply
I have a 18x33 above the ground pool. I had a 1.5 hp motor in it before but it struggled with the vacuum of my pool. Would this one be capable because I was looking to upgrade to a 2 hp with two speeds?
Reply
Hi Roy, If you are looking for a 2 HP 2 Speed Pump then we would suggest something like the Waterway 2 HP 2 Speed Above Ground Pool Pump this PL1502 pump is a 1.5 HP Single Speed and we do not carry the PureLine Pure Pro XL in a 2 HP two speed.
Reply
I intend to use this in a trout pond for aeration and water flow. The pond is medium size. Will fit a hard pipe to the outflow and have the water shoot in the air and back into the pond. Will this work for that? Cheaper than a pond pump.
Reply
Hi Mike, This is a gravity fed pump so this pump would need to be placed below the water level. For example, on an above ground pool, the water is above the pump which allows the water to feed down to the pump. If your pump is going to be above the water level then I would suggest something like the PL1601 PureLine Pure Flow Pump.
Reply
i currently have a sta rite JWPAS5F-2A4 1 1/2 hp. Is this a good replacement? Thanks
Reply
Hi Steve, Yes the PureLine Pure Pro XL would be a good replacement for the sta rite JWPAS5F-2A4 1 1/2 hp pump.
Reply
I just opened my pool but I think I have one of my hoses to thepump hooked up wrong. do you have a diagragm showing how hoses go
Reply
Hi. You can use our How To Assemble A SandMan Pump Filter System guide as a reference.
Reply
Does the outlet have male threads also? I can't tell from the photos. I'm looking to replace the pump for my Pro Line cartridge filter and I need the outlet to have male threads
Reply
Hi Mark, Yes the outlet does have both Male and Female Threads.
Reply
I need to replace a Pro Line SK P711-15H pump that was attached to a Pro line 817-0150 N cartridge filter. Is this pump a match for what I need?
Reply
Hi, Mark B. This pump can be used as a replacement. You will need to rotate the discharge.
Reply
I have a pentair 340210 1.5 HP pool pump motor that has locked up. I was wondering if this pl1502 would be an adequate replacement and if it’d fit for a replacement.
Reply
Yes the PL1502 PureLine Pure Pro XL would be an adequate replacement for the Pentair Dynamo 340210 and would fit as a replacement.
Reply
I currently have a jacuzzi Laser DV Assay 7 POS 1-1/2 V Fling Tri and would like to replace it with the PL1502. Is this a compatible replacement for my jacuzzi sand filter.
Reply
As long as your Jacuzzi Laser Sand filter is being used on an above ground pool then yes the PL1502 would be compatible with your system.
Reply
This the pump and motors correct? Or is the motor a separate purchase??
Reply
Hi. This is the complete pump and motor. You can also purchase replacement parts, using the Replacement Parts Diagram.
Reply
Will this pump work to replace our Sta-Rite JWPA5F7L-2A1 pump?
Reply
I have an old Doughboy sandfilter with a power pak II pump I noticed that the hose hook ups are different. Mine just slide over and clamp down how do I hook my hoses to this pump.
Reply
I am going to order the PL1502 pump but also need the connections for my hose from the pool. What parts are they? Thank you
Reply
Hi Gail, If you need the hose from the pool to the pump then you will need one of these Above Ground Pool Hoses. If you need the fitting that goes into the pump that the hose slides onto then you will need this Above Ground Pool Pump Hose Fitting.
Reply
I currently have a splapool model 72730 is this a good replacement and does this have an on and off switch?
Reply
Hi, Terri. Yes, this Pure Pro XL Pump - PL1502 is a direct replacement to the SplaPool model 72730. It does not come with an On/Off switch.
Reply
Thank you for your answer to my last question. Which Hayward pump is comparable? Which one is better?
Reply
Is this an acceptable replacement for a Waterway EZ48?
1081 POOL MOTOR
CAT NO: EZBN50
Model #: C55CXKDF-4855
Reply
Hi, Chris. All the info that you provided cross references to the motor, you will need to provide us with the pump model.
Reply
Hi,Will this replace a Penrtair 340210.Also I need a twist plug .
Reply
Hi, Tom. You can use this pump as a replacement. However, you will have to use your existing or purchase a new Twist Lock Cord - SPX1550WA1.
Reply
where can I obtain 1 3/4" fittings coming up short on-line
Reply
Hi, Tony. Replacement parts for this pump are available using the Pure Pro XL Parts Diagram.
Reply
I have a 27' 54" Round Pool, will this work for my pool and run my Kontiki2 cleaner? I am switching from a Hayward 2 -.25 HP 2 Speed pump, but I understand SPL means I don't really use 2 HP. I only use high for my Kontiki2.
Reply
Hi, Sandra. Yes, this pump will be able to operate a Kontiki 2 cleaner with a large enough filter.
Reply
We just hooked up our new pump and it loses prime as soon as we turn it on. (Like 5-6 seconds). What could be causing this?
Reply
We've got the pump installed and working but it makes a gurgling sound at times when the skimmer makes a whirlpool. What could be the cause of this?
Reply
Usually, this is a sign of air being pulled into the skimmer by a bit too much suction.
Reply
Do you have this same pump with a side discharge and a 3 prong cord? no twitst cord
Reply
Hi, Conrad. This pump does include a 3 ft - 3 prong standard power cord. The discharge on this pump can be rotated to the side, instructions are provided in Inyo's How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump.
Reply
I have a Waterway PEW2150-3GRP pump with side discharge that I need to replace. Will this pump work as a drop-in single speed replacement assuming I rotate the discharge outlet and reuse the existing twist-lock power cord? Do I need any additional fittings or adapters?
Reply
Hi Andrew, Yes this will work as a drop in replacement for the Waterway PEW2150-3GRP pump as long as you rotate the discharge and replace the cord as you have stated.
Reply
will this pump work with the jacuzzi sher-120 filter?It has a horizontal dish charge?
Reply
Hi, Larry. This pump can be used with the Jacuzzi Sher-120 filter operating an above ground pool. The discharge can be rotated, instructions are available in our How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump guide.
Reply
Well this pump work with the Hayward filter model number S190TSCP backwashrate 25gpm flow rate 45 gpm I’ve heard you cannot have a pump out work the filter I’m not sure what the flow rate is on this pump
Reply
Hi, Dave M. This pump will work with the S190TSCP model filter.
Reply
Hi, I have a JWPAS5F-2A4 pump right now. Can I use this as a replacement pump? If so I would need adapter from 13/4" to 21/2". Do you sell these too?
Reply
Hi, Dave. This pump can be used as a replacement. I will need to know what type of adapter you will need. You can also provide us with pictures.
Reply
Looking at 1.5 hp pump PL1502. Our current pump has male 1-3/4" on both input and output. Will this pump work?
Reply
Hi, Jeannie. This pump can work can work if you have an above ground pool and a large enough filter.
Reply
I have a 24' Round above ground pool would this pump do a good job on that size pool?
Reply
Hello, I'm interested in the poop pump PL-1502 to replace my splapool pump model 72730. My pump has a side discharge (to the right). I understand your pump is a top discharge. Do you sell a side discharge option? Or can I rotate the PL-1502 discharge 90 degrees? Thanks for checking.
Reply
Hi Tim, The PL1502 is a direct replacement for the splapool pump model 72730. The discharge port on this pump can be easily changed from top discharge to side discharge by removing a few screws, so this pump should work perfectly for you.
Reply
Will this work as a replacement for my Hayward model O18787320, have it on the Hayward E200 sandfilter and a 16'x48" intex pool
Reply
The picture is my current pump that needs replaced, will this one work as the replacement?
Hi Brad, Yes this would be a direct replacement for your current pump and would be an easy swap out.
Reply
My pump brunet out 3 weeks after the warranty expired :/ would this one work as a replacement ? adding photo of pump and filter too. And If he does can I use the same hoses for it?
Hi, Thomas. You will need to provide the model of the pump wet end in order for us to locate a suitable replacement.
Reply
My pump brunet out last week and I'm trying to find a good replacement for it. Would this be a good one for a 15x34 pool. adding photo of my current pump
I was sent an email saying they needed this to help me find a pump to replace that burned out on me. It's a waterway outdoor pro model sd -15-1n11cc
Technically, the direct replacement is the model PD11506 but you can use this model also as a replacement. Just keep in mind that you may need to modify the connections because if you currently are using unions threading directly to the external part of the pump ports then those unions may not work.
Reply
Ok, I think I understand now about unions threading. the hose from the pump to the filter has one. But the one from the pool to the pump doesn't. I was going to post a photo but no op in reply
Reply
I don't think I understand what you are saying about threading. so I would have to change the hose from my pool to my pump and from the pump to my filter? Not sure about that. the hose from the pump to the filter came with the filter. I watched the guys unpack it. could you link to something that would explain this better? I tired google and got a lot of mixed stuff and video's of Rednecking a pool lol
Reply
can the housing be relocated?
Reply
Hi, Sylma. The housing cannot be relocated, however, the discharge can be rotated using the instructions in our How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump guide.
Reply
I have a Hayward Power-Flo LX pump sp1580Z2 (D). It is for my above ground pool which measures 41’ X 21’ X 4’ (22,000 gallons). It also has 1 1/2” female threaded intake from the side, and a 1 1/2” female outtake that goes out the top. Will The Pureline PL1502 work for me?
Hi Marty, The PL1502 would work for you from a flow standpoint and connection standpoint however the port locations are about 1" different than the Hayward Power Flo LX so you would have some re-plumbing to do.
Reply
I have a intex 16x 48 and a intex sand filter sf70110. Which pump do i buy. And what extra fitting will i need. My hayward burned out. Thank you
Reply
Does this model have dual speed options
Reply
Hi, Sherry, the dual speed option will be available in a few months. If that is too long to wait then you might consider the Waterway 2 HP Dual Speed Above Ground Pool Pump
Reply
3yrs old always runs , yesterday turned it on and only hear a hum, does not pump. Is a new capacitor to be considered?
Reply
Hi. Testing and or replacing the capacitor will be our first recommendation.
Reply
I would also try turning the motor with some pliers or a wrench. Some time the motor just gets stuck and needs to be broke loose.
Reply
I Have an above ground pool pump Hayward SP1580X15. Will this pump be a good alternate and work the same, same fittings , dimension etc? Thank you
Hello, Can you please send a picture of the motor label?
Reply
Hi, I have a Hayward EC40AC filter, which had been paired up with a 2 HP Proline Pump (see images attached). Now, thanks to your pump-sizing video, I think this pump was probably over-sized for this filter, which may explain why I kept kept getting DE blow-through when starting up the pump in years past. Need to replace the pump now, so is this 1.5 HP pump a better fit for this filter? Pool is a 30' round above ground. Thanks!
Is a twist plug connection available on this model?
Reply
Hi, Dave B. It is not, you will have to purchase and install a Twist-Lock Power Cord - SPX1550WA1 separately.
Reply
I have a Dirt Devil (Cantar) above ground pool pump/ filter system. I removed a defective A.O. Smith 1.5 HP, 2 speed 115V motor and need a replacement.
Wondering if this pump will be easy to swap out. I'm also wondering if I can purchase with a twist plug option.
Thanks!
Hi, Dave B. This PureLine PL1502 will not be a drop-in replacement due to the proprietary connections and design. You can use the SLR9 1.5 HP Horizontal Discharge - 94022435. It includes a standard power cord but it can be switched to a twist-lock cord.
Reply
Will this pump connect to my Intex sand filter
Reply
Hi Jason you would need to purchase the following Intex Pump Adapters for this to work.
Reply
Will this replace a Hayward Power Flo Matrix SP1593? Do I need any additional adapters?
Reply
Hi, Patrick. This Pump can be used to replace the Hayward Power Flo Matrix SP1593 model pump. You can reuse your Hose Connectors 1.5" - 4564 if used.
Reply
I need to replace a Sta-Rite Dynamo 1.5HP pump, would this be a suitable replacement and will the same connections and hoses work?
Reply
Hi Johnny, Yes the PureLine Pure Pro XL would be a suitable replacement pump for your Sta-Rite Dynamo 1.5HP pump. To determine if the connectors would hook up to your current system we would need a few photos. Please click on the reply link below and upload a few photos of your system, a wide shot, as well as a close up of the connectors, would be helpful. Once we get those photos we will let you know if the same connectors will work.
Reply
I have a century pool pump and it is needing to be replaced . Will the PL1502 be able to replace it
What is the model number of the pump housing? The pump housing info will help be a more significant help in determining the correct replacement.
Reply
I need to replace the lid and the basket inside the pump. Do you carry these and or is it an option to just replace these 2 items?
I have a Sta Rite Dynamo High Performance pump.
Reply
Yes you can replace these parts here is a link to purchase Parts for the Sta Rite Dynamo Pump
Reply
Will this pump replace model # S55CXRJC-8049?
Hi Christy, Yes the PL1502 would be the suitable replacement for your S55CXRJC-8049. The plumbing ports may not be in the exact same spot so you may have some minor re-plumbing but it should be minor.
Reply
I have a hayward high rate sand filter model # S180T & hayward pump SP1515-Z-1 will this pump work need to replace pump thanks
Reply
Hi Russ, yes this would be a great replacement for your Hayward SP1515-Z-1 being used with the S180T Sand Filter.
Reply
Is this pump powerful enough to use a 3 tier water fountain in my pool?
Reply
Hi Angie, Would it be possible to send a few photos of your pool and your fountain? This would help us make the proper determination. Do you have an inground or an above ground pool? Simply click on the reply link below to upload your photos.
Reply
Above ground pool Picture of fountain attached This is the only picture I have, I’ve actually already purchased and received the pump yesterday... but would still like to know if it’ll work.
Hi Angie, The PureLine Pure Pro XL should have no problem powering your fountain. However if there is any issue then our customer service will take care of you in getting the correct pump.
Reply
I use my pump with a chlorinator my pump doesn't have a filter on in is there another part number for the pump with out the filter?
I have a picture of the label.
Hi, Frank. You will need to provide us with the model of the wet end that is attached to the motor in the picture uploaded to us in order for us to assist you.
Reply
Hello, I’m definitely a beginner at this pool scene and currently have a best way sand filter for my above ground oval 9’x18’x4’. I’m looking to upgrade my pump because this best way just isn’t cutting it for me. Will this pump still work with the best way filter or would I need to buy another filter? Thanks for helping out an eager rookie.1.5 HP Above Ground Pool Pump - PL1502
Reply
Welcome, Ricky! Would it be possible for you to send us a few photos of your Best Way Filter System? To send us the photos simply click on the reply link and upload your photos. Once we get those photos we could make the proper recommendations.
Reply
So sorry thought I added them. Please see attached photos
Hi Ricky, Thanks so much for the photos those are quite helpful! I would suggest both a pump and filter as if you just upgrade your pump then it will pumping more water than your filter can handle. For example, the new pump could output 60 Gallons Per Minute (GPM) and your current filter may only be designed to handle 30 GPM, this will cause additional stress on the pump and shortening its lifespan. My suggestion would be the PureLine PL1510 Pump and Sand Filter System however that system is scheduled to be shipping June 1st, so if you can wait that would be what we suggest for your pool.
Reply
Thanks Patrick, The pump/filter you suggested is a 1hp. I’m thinking of getting something that I may be able to use in the future. if I decide to pull the trigger on a fiberglass pool I’ve had my eye on. So my question is can a 1.5 hp pump be ok for my current size pool and can that handle a 16,000 gal pool (in the future)
Reply
Hi Ricky, the 1.5 HP Sand Filter System would be a bit of overkill for the Best Way pool but you could do it. The main problem would be that the pump on the PL15 series is a gravity fed pump meaning that the pump needs to be below the waterline of the pool. Most likely the fiberglass pool will be an inground pool meaning the pump will be above the waterline and you will need a Self Priming Pump like the PureLine PureFlow PL1601. If you go with the PL1601 pump then you would need to go with a filter like the Hayward S180T. If you go with this set up you would need to use rigid PVC which mean a bit of re-plumbing on our Best Way Pool.
Reply
I purchased the 1 hp pump and filter you recommended. I’m also looking into this Remington solar chlorine free sun shock system. I live in Miami, fl and the sun is sweltering and then the normal 2 hour rain storm really make it a pain to keep chemicals balanced. Do you think this system would work on my vinyl pool? I’m worried the copper it releases may damage the fabric. Like I stated in my first comment I am a beginner and maybe it’s a gimmick but looking for expert advise. Thank you
Reply
Hi Richard, I too have been concerned about introducing metal into the water causing staining. We have always found the best results by making sure your CYA, pH, and Chlorine are balanced. These are the most important items to monitor if you monitor these on a weekly basis and keep them in the proper range then maintaining your pool should be a breeze. This Video on How to Clear a Green Pool goes over a lot of good basics on water chemistry which you should find helpful.
Reply
Is this pump enough to replace a hayward dynamo 1 1/2 horse that i have now? I have a sand filter and a 10,000 gal 24 ft above ground pool.
Hi, Renee. Yes, you can use this Pure Flo XL Pump - PL1502 as a replacement.
Reply
Hi I have this same Pentair pump and I ordered this PL1502 replacement pump but my hose from filter to pump will not fit on new pump. Just curious how you were able to connect it . thanks
Reply
Hello, I recently purchased a home with an above ground pool. The existing pump seems to be no good. I’m wondering if this pump would be an acceptable replacement. I’m brand new to pools so if this is not the proper replacement I’m open to suggestions, thank you
Hi, Nicole. In order to suggest a replacement, I will need to know the size of your filtration system.
Reply
Does this convert to side discharge?
Reply
Hi, Chris. Yes, it can. Instructions are available in our How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump guide.
Reply
Will this pump replace a 1.5 h.p. eco kleer
Motor?
Reply
Yes this pump is a replacment for the Eco Kleer pool pump but if you have hose connections that thread to the outside of your pump ports then you will need to use standard male threaded fittings for the ports and hose clamp your hoses to them.
Reply
My current Hayward pump is electrically hard wired to an electric box that runs underground to a power switch under my deck. My question is do you have a 1.5 HP pump that I can wire into this to replace the Hayward. I only see a corded option and I have no other power supply to that area.
Hi, Brian. You can remove the power cord and hard wire this pump.
Reply
I need to replace this Hayward 1.5hp pump that lasted 30 YEARS attached to a 27' above ground pool! Can i replace it with this this pump? I'm 65 so I don't need the new one to last 30 years. And of course I wouldn't be using the plastic base the the old one is attached to. Thanks!
Hi, John. Yes, you can use this pump with your existing filter.
Reply
I plan to use this with my Hayward 180T sand filter. My question is- will an auto pool vacuum work with it?
Reply
Hi, Kathy. Yes, this pump along with your Hayward S180T sand filter will be able to operate an automatic pool cleaner.
Reply
I have a Hayward Power Flo LX SP1580x15 that has died. The company that installed our 27 foot round above ground pool no longer sells Hayward, but they have advised me if I purchase the PureLine 1.5 HP Above Ground Pool Pump - PL1502, the fittings that screw into the ports may not match exactly. Is that the case? I'm looking for a pump/ strainer basket that I can attach my current hoses to and plug in without having to call an electrician or plumber. Would the PureLine 1502 work for me?
Hi Julie, Yes this PureLine PL1502 Pure Pro XL would replace the Hayward Power Flo LX pump in your photo. We would suggest purchasing the hose adapters listed on this page which would allow your current hoses to connect with minimal difficulty.
Reply
We are replacing a Pentair 340190 - will this work?
Reply
Will this replace the Hayward Power Flo Matrix pump. Model # SP5500Z2(B) connected to A Hayward Sand Filter Model # S210T93S.
Yes this PureLine Pure Pro XL will replace your Hayward Matrix pump.
Reply
Will this pump work for my 27 by 54 above ground pool? Current pump I have is Dynamo High performance Model number 193262
Reply
Hi, Yes this PureLine Pure Pro XL would be a great replacement pump for your Dynamo Pump on a 27 by 54 above ground pool
Reply
I have a 29 ft radious pool 5ft deep. I currently have a dough boy 1.5 pump. Can I use this for a replacement and will it be efficient.
Reply
Hi Hank, This would be a great pump for a 29' pool and it will be efficient. You may have a little re-plumbing but it should be nothing major.
Reply
I am replacing a Hayward powerflo matrix pump with a de filter. What fittings do I need to make the connections work.
Reply
Hi Mike, both pumps have 1.5" female and male ports. It looks like the Hayward Pump with a DE Filter has a Side Discharge but you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
Does the pump turn off when it needs to and turns back on all by itself? I'm trying to see if my pump is broken.
Thanks
Reply
Hi, Lonnie & Ronda. The pump will automatically turn On/Off only if it's operated by a timer. Otherwise, it will have to be plugged in and out.
Reply
I have Sand filter and pump would like more pressure for water flow to the pool can I run a second pump along with the existing pump and filter
Reply
Hi, Darryl. Unfortunately, you're unable to use a second pump with an above ground pool with (1) skimmer and (1) return.
Reply
Where is thermal breaker located in pump motor?
Reply
The thermal protector lays on the coiling inside the motor. Attached is a picture for your reference - Picture of Location of Thermal Overload Protector
Reply
The attachment points for the PVC pipes can I shift them to face another direction my current motor faces the right
Reply
Hi Bryan, Yes you can rotate the discharge port on this pump by these instructions listed here... Please click the following link for How to Rotate the Discharge Port on a PureLine Pure Pro XL Pump.
Reply
I have a 1 HP Hayward pump & motor which I've had since 1993. Thinking of upgrading to 1 1/2 HP. Will this fit my Hayward filter model # EC40-75?
Reply
Hi Roger, both pumps have 1.5" female and male ports. It looks like the Hayward Pump with a DE Filter has a Side Discharge but you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
I'm replacing a Baquapure waterways 2.5 hp pump with 2" fittings. It's a24ft above ground, 13, 500 gallons. What adapters do I ares available to make this one work with my filter?
Reply
Hi Robert, Could send a few photos of your pump and filter including a wide shot showing the complete system. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
We are looking for sp 1510 z1 xehc -what is different from this one.
Hi Janet, The PureLine Pure Pro XL PL1502 is a 1.5 HP vs. the Hayward Matrix in your photo is a 1 HP so the Pureline will be more powerful. The plumbing ports on the pumps will not be in the exact same location but since you are using flexible hoses this should not be an issue. The warranty for the PureLine will be better in the sense that it still carries the full 1-year warranty if it is purchased online where Hayward limits there warranty if their pump is purchased online.
Reply
should the pump housing be loose from the pump? It is not tight, you can actually move it a little with your hand. It doesn't leak or
anything and seems to work fine.
Reply
Hi. Due to the pump design, the strainer portion will appear to be loose. This is okay.
Reply
How do you hook the lik shark vacuum to the above ground pool pump?
Reply
Hi. Instructions are available in the Kreepy Krauly Lil Shark Owner's Manual. The unit is to be connected to a skimmer, it's unable to connect directly to the pump.
Reply
My sand filter says 80 gpm. Is this pump too much for it to handle?
Reply
Hi Lee, An 80 GPM Sand Filter would be able to handle this pump just fine. Please note this pump is for Above Ground Pools and not Inground Pools.
Reply
Will this pump be compatible as a replacement for the pentair dynamo 1.5 hp 340210?
Thanks,
Rebecca
Reply
Hi Rebecca, As far as power goes and the electrical cord this would be a great replacement for the the pentair dynamo 1.5 hp 340210. The plumbing ports on the pump are not in the exact location as the Dynamo so you may have a little bit of re-plumbing. If your filter is using flexible hoses between the pump and filter this should not be an issue.
Reply
Is there an off/on switch on the pump like my Pentair 1 hp pump
Reply
Hi Chris, The PL1502 does not have an on/off switch. For the model with the on/off switch you would need to order the PL1532 1.5 HP PureLine Pure Pro XL Heavy Duty the PL1532 will come with an on/off switch and upgraded heavy duty Viton O-rings, Gaskets and Shaft Seal.
Reply
Pool newbie here...I bought this pump to replace Waterway Ecco 1.5 hp pump. Also have Ecco sand filter. Connections don't match with hoses from either filter or old pump. Is there anything that will make these hoses and connections work together?
Will this work for a 30 ft above ground pool with 54 " sides? Our current pump was 2 hp and quit working. I am thinking we probably could go with 1 1/2 hp from everything I have been reading.
Reply
Yes we suggest a 1-1/2 HP for a 30' Round Above Ground Pool and the PureLine Pure Pro XL would be a great option for you.
Reply
This is what our current pump says, what would be comparable, our pool is a 30 ft above ground with 54" sides.
The PL1502 would be comparable in power to the Aqua Pro Pump in your photo. The plumbing ports are not in the exact same spot so you may have a little re-plumbing.
Reply
I am new to this. Will i have to buy a sand filter, or can i just hook this pump to my pool to clean it.
Reply
Will this pump relaxed the pentair and the hoses fit thank you Cathy
Our Hayward pump just burned itself out. Is this model the correct replacement?
Turned my pump on and it turned on and sounds normal. It has on off switch 1.5 like those black ones picture. It is hooked up to a large sand filter. Thought all was good BUT put hand on suction intake hose and not much suction. Usually good suction/ when low suction I would backwash. The output hose is pushing out water but not as good as last year. Both holes have less power. Took off hoses, not clogged, but no change. Does this mean pump going out or broke or do I look for another issue?
Reply
Please see our How to Correct Low Water Pressure Blog shown here http://www.inyopools.com/Blog/how-do-i-correct-low-water-pressure/ it sounds like a clogged or dirty filter.
Reply
Hi, I want to make sure I order the right pump. Can someone help me to verify and help me to find the right model? thank you
Natasha, the model information provided did not indicate what pump model you are working with. In order to suggest the right pump, we will need to know that information. Please send us the model number of the pump housing.
Reply
SO I HAVE A HAYWARD SP1593, IS THE SAME PUMP??? ALSO DOES THE 1.5 PORT MOVE LIKE THE HAYWARD SO I CAN ATTACH IT TO MY FILTER? IT ATTACHES FROM THE SIDE NOT THE TOP
Reply
Hi Mark, This pump is comparable to a SP1593 but it is not the same pump. The 1.5" port can be rotated by following this Guide on How to Rotate the Discharge on Pure Pro XL to Horizontal
Reply
this pump comes with the strainer basket. everything that is in the pictures correct??? only confused because you have a video of how to replace just the pump in the pictures of this item.
Reply
Hi Nate, Yes this pump comes with the strainer basket. everything that is in the pictures.
Reply
We currently have a Hydrotools Swimline 1.5 HP pool pump with sand filter system. Model # is 71610 / 71915. Is the PL1502 a good replacement for this pump? If so, will we need additional connectors for the plumbing to connect? Thank you!
Reply
Hi Canessa, Yes the PL1502 would be a direct replacement for the pump on your Hydrotools Swimline 1.5 HP pool pump with sand filter system Model # is 71610 / 71915
Reply
Will additional connectors be needed or will everything line up properly?
Reply
Hi Canessa, from what I'm seeing everything should match up the same and no additional connectors would need to be purchased.
Reply
Will this work with a Waterway Clear water high rate tank Diam. 22" max flow rate 55 GPM. 24ft above ground pool
Hi Tom, Yes the PL1502 PureLine Pure Pro XL would be a great replacement pump for your system. You may need to get 2 of these hose adapters if you do not already have them on your current system.
Reply
I have a Hayward maxforce 1.5 will this pump work ?
Reply
Hi Shawn, Could you confirm the model name of your Hayward Pump? I'm not familiar with the Max Force name, Hayward does make a Max Flo, Super Pump and Power Flo. I will wait for your reply with confirmation.
Reply
I need to replace this motor. What do you recommend?
Hi August, This is NOT the correct replacement pump for the motor included in your photo. You will also need this SuperFlo Seal Kit We also put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
Does this pump have on/off switch?
Reply
I need to replace my pump - I currently have a 1 HP Hayward Power - Flo Matrix - will this work?
Reply
Hello, This unit will be able to work, you would want to check the max gpms on your filter first.
Reply
Hello will this work with a Hayward cx410re 28 foot above ground pool
Reply
Hi Dan, This pump will be a little too powerful for your Hayward cx410re. We would suggest the PureLine Pure Pro XL 3/4 HP Pump
Reply
I have a Hayward SP158072/S48E48A04 Is this pump compatible?
Reply
In terms of power, this will be a great replacement for your Hayward SP158072/S48E48A04 and this pump is compatible. If your pump has a Side Discharge then you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
Do you recommend a different pump that would be more compatible? One that I wouldn't have to shim, etc.
Reply
Could you post a few photos of your pump and filter, especially a wide shot showing both the pump and filter? To supply photos simply click the reply link below and upload your photos. This information would help us determine if any modifications would be needed.
Reply
I am trying to match this pump up with a STA-RITE High rate sand filter and I need a picture of how to hook up to pump and filter?
Reply
We do not actually have a picture showing how exactly these are connected however, if you use part number 4800-80 then you would thread the black fittings to both the pump port and valve port, and attach the hoses to them using the metal clamps.
Reply
Will this pump be a good replacement for this pump I really love this pump because it really does push some water but it is so loud
Hello,Can you provide a picture of the pump housing or its model number?
Reply
i'm replacing my 1.5 HP Motor, Speck Pumps Model number E90-I / Serial number 275300 it's hard to read. would your PL1502 work. or do you have an equal.
Hi Sal, As long is this is being used on an above ground pool and the PL1502 is below the water level of the pool then yes this would work. The plumbing ports on the PureLine are not in the exact same spot as your speck pump so you may have a little re-plumbing.
Reply
Can I use this pump stand alone to vaccum an in ground pool ?
Reply
Hi Daniel, You could not since in that scenario the pump would be above the water level and this pump is not a self-priming pump meaning it cannot pull water up to it. You could use the PL1601 PureLine Pure Flow Self Priming Pump and you could add this 115V 3 Prong Cord to that pump.
Reply
Hi .ihave a splapool pump model # A72730 will ure pump # pl1502 be a good replacement ?
Reply
Hi Jim, Yes the PL1502 would be a great replacement for the splapool 72730 The plumbing ports on the PL1502 are in the exact same location as the 72730 so installation should be simple.
Reply
is this the same as a hayward power flo lx 1.5
Reply
Hi Lee, In terms of power and gallons per minute output the Hayward Power Flo LX and PureLine Pure Pro XL will be the same. The plumbing ports between the two pump are not in the exact same position so if you are using hard plumbing you may have a little re-plumbing.
Reply
Will this work as a replacement for my waterway pump?
Hello - the model number (ps-15-2n11mc) on your pump comes back as a dual speed, this Pureline pump is only a single speed. This Pureline will work but you will not be able to change speeds as you do now.
Reply
I am not concerned with the two speeds, I wanted to make sure it will fit my filter with the output facing right not up. If not is there another pump that you can recomend?
Reply
Hi Jim, the ports on this PureLine pump will not be in the exact same spot as your current pump. We would suggest this Waterway Pump which will have the same plumbing port location as your current pump.
Reply
I can see from the picture that this pump has a different plug than my current Hayward pump that I am trying to replace. Is there some kind of connection that will allow us to plug this into that socket?
Reply
Hi, Sally. Using an adapter is not safe or compliant with the National Electric Code (NEC). You can swap out the power cord on the pumps.
Reply
Hi, I have a Proline Above Ground pump SK P711-15H, Model PE71-II-H that I need to replace. The filter that I have is a Waterway Clearwater II DE Filter - FD18 (Horizontal discharge).Will this pump be a good replacement?
Reply
In terms of power, this will be a great replacement for your SK P711-15H, Model PE71-II-H and this pump is compatible. If your pump has a Side Discharge then you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
are you offering the same 20 % discount which is being offered by google for first time buyers. I qualify if you do. Im interested in the 1.5 pump single speed 110 volt pump for 139.00 dollars free shipping.
Reply
Hi, Marc. Unfortunately, we do not accept any Google coupons.
Reply
I have a Splash Pool and my pump motor is blowing my breaker, also squeeling. Can this pump replace mine?
I found a part number on it - P/N 340210SR - it's a Dynamo brand
Reply
Yes, as far as motor specifications this would be a suitable replacement pump.
Reply
Which pump would work best for our pool?
Hello - are you replacing the pump and the filter or just the pump? We have this guide that shows you how to size either of these components: How To Size an Above Ground Pool Pump and Filter System
Reply
Hello, I am needing to replace a Lomart ultra Promega 1.5hp pump (doughboy brand) . I am not sure about the treading ect on it and cant find much info online, just curious if this pump will work?
Reply
Hello, As long as you don't exceed the max GPMs on the filter, you will be ok.
Reply
Will this replace be same as my Pentair Dynamo 1 1/2hp pump? Also I have a Pentair filter system will it fit the connectors?
Reply
These two pumps differ in an important way; the Dynamo is self-priming, and the Pure Pro is not. This means if your pump is set above the pool's waterline then the Pure Pro XL would not be able to draw the water up and into the filter. If your pump is installed below the pool's waterline then it is a suitable replacement.
Reply
Is the strainer basket cover that comes with this pump is it a 1-piece unit or is it a 2-piece? For instance, is the clear window part come apart from the black collar?
Hi, Richard. The Pump Cover for this pump is one piece.
Reply
Will this replace a Hayward power too matrix 1.5 up pump on a Hayward extreme filter system
Reply
Yes, this pump is a compatible replacement for that Matrix but it will not use the same external union assembly that the Matrix may use.
Reply
I have this pump. It’s not working will this pump be a good replacement? I am looking for a little more power. I have a 30 ‘ above ground and it seems 1 hp wasn’t quite enough. Also it has the funny plug not a regular outlet. Also how long to Albany NY? Is it hard to swap out? I know. Lots of questions.
Hello - your current pump is a Doheny's 72728 3/4 HP pump, if you decide to make the jump to 1.5 HP I would check your current filter's flow rate capacity to confirm it can handle the larger pump.
Reply
Will this pump safely replace my current pump? I don’t want to reduce the hp or the gpm and ruin my sand filter. Thank you.
In terms of power, this will be a great replacement for your Hayward Power Flo LX and this pump is compatible. If your pump has a Side Discharge then you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
My current pump is leaking. Will this be a good replacement? Will the connections fit to my filter?
My pool is a 15x30 above ground. I also have a knob to shut off water flow to pump in order to open and clean cartridge filter, will this still work on this model?
Will this work for our Jacuzzi filter (120SH) and do we need any connectors ?
Hi, Lisa. Unfortunately, it will not work based on how your pool is installed and the style filter connection you're using.
Reply
Will this work with our Jacuzzi 120SH filter? Will the same connectors work, or do we need to order some with the pump?
Hi, Lisa. Unfortunately, it will not based on how your pool is installed and the style filter connection you're using.
Reply
I am looking to replace out 2 HP 340078 Pentair side discharge pump. Would this be a good replacement? Our pool is a 30ft round.
Reply
Hi, Kristen. This pump can be used, however, it's not compatible with any of the Pentair fittings.
Reply
I have a DE filter system with 1hp Hayward Powerflo Matrix pump with a Horizontal discharge into the filter housing that uses a double threaded coupling to connect the pump to the filter. Can this pump be configured so that the discharge is horizontal and not Vertical?
Does this pump have an on/off switch?
Would this pump work as a replacement pump for our application?
Hi Ronald, You can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump. The PL1502 does not include an on/off switch but the PL1532 1.5 HP Pure Pro XL does include an on/off switch.
Reply
I have a eco Kleen 1.5 hp for a 26 sand filter my pump or motor quit dont know if they are one thing but would this one work
Reply
Hi Debbie, Yes this is the suitable replacement motor for the pump used on an eco Kleen 1.5 hp or a 26 sand filter. Sometimes you may need to get a few extra plumbing fittings to hook up your current hoses to this pump and we carry all of those fittings. If you post a few photos of your filter system then we can let you know if any fittings are required. To post photos simply click the reply link below.
Reply
I have the same eco kleer pump & I am replacing with this one. I was wondering if my old plumbing will work with the new rig also. Yo
Reply
Hi Jason, Could you post a few photos of your system? Please click the reply link below to upload photos.
Reply
I have had a proline 2hp pump for 15 years now will your pump be compatible with my system on a 15ft above ground pool
Hi Daniel, Yes from a power and Gallons Per Minute (G.P.M) standpoint the PL1502 would be a suitable replacement for your current pump. I'm not 100% sure if your current union on the top port of your pump will screw onto the PL1502. If it does not then you would cut off your current union and replace with this PureLine Pump Hose Adapter and this Hose Clamp
Reply
Can I get this delivered to a California house
Reply
Hi Robbie, I'm sorry this cannot ship to California as you will need a variable speed pump in California. I would suggest this PureLine Pure Flow 1.5 HP Variable Speed Pump
Reply
Need to replace an AO Smith (Century) 1 HP pump that has a cracked case as well as being older. The RPM is 3450, the pump part# is O-186884-10. Attached by hoses to a sand filter. Will this work ok or should I get the 1HP model?
Reply
Hi, Mark. Unfortunately, I'm unable to confirm using the info provided. I will need to know the make and model of the casing. The info provided is the motor which cross-references to the BN25V1 motor.
Reply
Will this picture help?
Mark, That is for the motor, need to the pump housing model or name.
Reply
Can I use this on my old Jacuzzi CFR 100 above ground pool pump that is side discharge?
In terms of power, this will be a great replacement for your current pump and this pump is compatible. Since your pump is Side Discharge then you can rotate the discharge on the PureLine PL1502 to be side discharge by following this Guide on Changing the PureLine Pure Pro XL to Side Discharge. You may also need to put some shims under the pump or filter so that the port on the PureLine Pump match up with the inlet port on your filter. Outside of these few modifications, everything would work just fine with this pump.
Reply
Have 1 hp motor with pentair dynamo dynII-n2-1 1/2 pump. Is this pump too much or should I go with the 1 hp version
The 1.5 HP Pureline Pure Pro XL is a compatible replacement with the Pentair Dynamo 1 HP, they put out similar flow rates.
Reply
whats the best model pump to use as portable pool pump ,as i have a pump already thats stationary.i want to pump the pool the days that my pool man is not available?
Reply
Does this come with the hoses to connect to the pump/filter/pool? If not, what do I need? Thanks!
Reply
Hi, this product is the pump and motor $139.dollars as show in picture or is only the pump and how soon can this be ship to New york.
Reply
We are currently sold out of the 1.5HP's without a current ETA. We have the 1 HP Above Ground Pool Pump - PL1501 in stock and ready ship. All orders received after 1:00pm ET will process the following business day, standard ground delivery is estimated at 1-5 business days.
Reply
I have a intex crystal clear sand filter with 3/4 hp pump. Will this pump work with the 16 inch sand filter I have . I need to replace the pump. I am enclosing a picture of the specs on the system. Thank you
The 3/4 HP Above Ground Pool Pump Salt Friendly - PL1508 would be the ideal recommendation with your filter model. We also offer the combos shown here http://www.inyopools.com/ProductListing/clearance_pool_pump_filter_system.aspx
Reply
Will your pump replace our existing pump (see picture)? This is so much less than what I can find to replace with the same brand. I want to make sure it is the equivalent.
Hello, You will need a dual-speed to match with what you have. This will be a better alternative option for you. http://www.inyopools.com/Products/07501352063371.htm
Reply
can I use this pump to vacuum of 15feet depth under ground pool?
Reply
The PL1502 is not a self-priming pump. This means it is gravity-fed and must be lower than the body of water. It will not work with inground pools.
Reply
I am looking to replace my current pump. I do not care about currently having two speeds and am fine with moving to a pimp with a single speed. Will this be an accurate replacement?
Hi Ashley, Yes this pump would be a suitable replacement.
Reply
My pump is still working well after many years of service. I'm looking for a replacement filter cover exactly as shown. Can the cover and O-ring be purchased separately?
Reply
Yes you may purchase the lid through this link - Pure Pro XL Lid and the O-ring through this link - Pure Pro XL Lid O-Ring
Reply
i need to replace SP1515Z1BC
Reply
Yes, this pump is a suitable replacement for a SP1515Z1BC depending on your filter you may have a little re-plumbing. If you are using a sand filter with hoses on an above ground pool then this should be easy and no re-plumbing.
Reply
I'm installing a 21 x 41 dog training pool. Our cartridge filter is rated at 525sft, could you recommend a suitable pump to achieve high flow and filtration. Thanks
Reply
We will need to know the GPM rating of the filter. If you can give us the manufacturer and the model of the current filter we can find something that will work with your filter system.
Reply
Is there a on/off switch on the motor?
Reply
Hello Paul, The Pureline 1.5HP Above Ground Pool Pump is not manufactured with an ON/OFF switch. For ON/OFF control the Above Ground Pool Timer models P1101 or P1121 would be compatible. Intermatic Above Ground Pool Timer 3 Prong Receptacle (No GFCI) - P1101 Intermatic Above Ground Pool Timer 3 Prong Receptacle - P1121
Reply
how can I get the pump cover to lock
Reply
Hello Mary. If you are encountering an issue with the pump lid sealing, lubricate the pump lid o-ring with a silicone or Teflon based lubricant. If the issue persists replace the pump lid o-ring. The pump lid should hand tighten in a clockwise direction. Pool Pump Lid O-ring - PL1586
Reply
would this pump be a suitable replacement for a Jacuzzi Model S1B-6-S1 pool pump? The current pump motor has died and since this pump is 15 years old i was thinking total replacement instead of replacing the A.O.Smith 7-187610-21 motor.
Reply
Hello Calvin. The Pureline 1.5 HP Above Ground Pool Pump PL1502 would be a suitable replacement for the Jacuzzi Model S1B6S1 Above Ground Pool Pump. The increase in pump HP will improve water circulation in the pool. This change will likely require plumbing modifications.
Reply
Purchasing a 18 foot round pool i need a cartridge filter and a pump. What do you suggest?
Reply
Hello Joe. Attached please find a brief tutorial on the subject of Above Ground Pool Pump and Filter Systems. How To Size an Above Ground Pool Pump and Filter System In a cost/value analysis, the 2 systems that merit consideration are: Pentair Products EC-PNCC00750E1160 Above Ground Cartridge Filter System Clean & Clear® Aboveground Cartridge Filter System - EC-PNCC0075OE1160 and the Waterway ClearWater II Cartridge Filter System 522-5167-3S. The Waterway System is slightly oversized (1 1/2 HP pump with 150 sq ft filter) but it has dual-speed capability (lower energy consumption on low speed and better filtration) and is currently available at a reduced price.
Reply
Is this pump suitable for salt water pool?
Reply
Hi David, the seals from the factory on the PL1502 pump are designed to work well in salt- or freshwater pools.
Reply
Hi,
Will this replace our current pump.
Your pump is sold exclusively at Doughboy Pools. Unfortunately, they do not provide information about it to cross-reference. We offer Sizing Your Above Ground Pool Pump https://www.inyopools.com/blog/sizing-your-above-ground-pool-pump/ The MODEL # PL1502 is a gravity-fed pump, if your pool is submerged or partially submerged in the ground you cannot install it, it is not a self-priming pump like the 1.5 H.P In Ground Pool Pump - PL1601 https://www.inyopools.com/Products/00100018074613.htm
Reply
will it replace this?
Hello Phillip. The PureLine 1.05 HP Above ground pool Pump PL1502 is a compatible replacement for the Hayward Power-Flo LX 1.5 HP Pump. installation may require plumbing changes depending on your current configuration.
Reply
Will this replace a Pentair 1HP 340197? Does it haver an on/off switch?
Thanks
Hello Dominic. The PureLine 1.5HP Above Ground Pool Pump model PL1502 is a compatible replacement pump for the Pentair Above Ground Pool Pump model 340197. The PL1502 does not come equipped with an On/Off Switch. The use of the Intermatic Above Ground Pool Timer 3 Prong Receptacle (No GFCI) - P1101 would eliminate manual operation. The PL1502 installation may require plumbing alterations.
Reply
Would this replace the current pump I have? Also I attached a photo of my filter just wanting to make sure it would all work together properly.
Hello Casey. The PureLine 1.5 HP Above Ground Pool Pump model PL1502 is a compatible replacement for the above-ground pool pump and filter in the photo provided.
Reply
1 does it have an on/off switch . 2 can you rotate the intake 1/4 turn as that is my current setup so it faces the filter
Reply
Hello Chuck. The PureLine 1.5 HP Above Ground Pool Pump PL1502 does not come with an on/off switch. The installation of the Intermatic Above Ground Pool Timer 3 Prong Receptacle (No GFCI) - P1101 would eliminate the need for manual operation. The Discharge Port can be rotated by following the steps described in the brief tutorial How To Rotate the Discharge Port on a PureLine Pure Pro XL Pump
Reply
How big of pool can this handle I have a 27x5
Reply
Hello. The 1.5 HP Above Ground Pool Pump - PL1502 is compatible with an Above Ground Pool with the dimensions of 27 x 5. Attached please find a brief tutorial How To Select Above Ground Pool Pumps (note Step 2) for reference.
Reply
