I need to replace my pool pump motor for my salt pool. Is PL2853 the correct one? I have a Pentair 7-177474-01, Frame 56Y, Hz 60, Amps 7.1/14.2, Phase 1, Volts 230/115, HP (just shows ----), SF (also shows ----). It is attached to a Whisperflo WF-24 part number 011772. And is the GOKIT32SALT the correct tune up kit? Thank you.
Reply
Yes, that motor and seal kit is the correct replacement parts.
Reply
Sf-n1-1a. Is this correct motor for pentair superflow. Model number196238
Reply
Hi, Your pump is actually a 1 HP Full Rate Pump which is equivalent to a 1.5 HP uprate motor so you would need the PL2854 1.5 HP Up Rate Replacement Motor We do show where you purchased the 1 HP up rate motor would you like for us to bill your credit card the difference and ship out the 1.5 HP Up Rate Motor, also we would suggest this Super Flo Tune Up Kit when replacing your motor. Finally here is a Video on How to Replace a Pool Motor which you may find helpful when tackling this project. We will put your order on hold until we hear back from you on how you would like to proceed.
Reply
I have a Whisperflow (WFE-4). The current motor PN is 011513. Is this the correct replacement motor?
Reply
Hi Greg, Your motor is a Full Rate 1 HP motor which is equivalent to a 1.5 HP up rate motor, so you would require the PL2854 Replacement 1.5 HP Up Rate Motor we would also suggest a Whisperflo Tune Up Kit when replacing your motor. Finally here is a Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I need a pool pump, which one should I buy? My previous pump was a Century Centurion with CAT: BPA449, 1.25 Horsepower, PH 1, VOLTS: 208-230/115, AMPS 6.0-5.6/11.2, TYPE: CX, HZ: 60, RPM: 3450. Thank you.
Reply
I need a pool pump. The one I have now is:
Century Centurion
CAT: B2853 SERIAL: 10814CH
TYPE: CX FRAME: P56Y
HP: 1.0 SF: 1.25 PH: 1
Additional Information:
1081 Pool Pump, Duty Mount Horiz with Vent Holes Down
What should I replace it with???? Would it be better to buy one with more HP?..
Reply
looking for a replacement motor Pentair model # WF-24 1HP part # 7-177474-01 which replacement motor and seal kit should I buy
Reply
This PL2853 is the correct replacement and you will need this Pentair WhisperFlo Seal Kit
Reply
Our Jandy Shpf1.0 pool motor just recently started screaming. Would this motor work for our application? Thank you in advance
Reply
Hello, I have a Pentair motor nubmber
196238 it is a one
horsepower motor for an inground pool. I was wondering which motor you have that I would need to replace it. Thanks.
Reply
By the way, my current pump motor is WFE 3, 3/4HP and service factor is 1.25. So which 3/4 HP motor fits my current one with a higher service factor ?my another concern is How to wire the motor with current wiring ? Thank you.
Reply
The 3/4 H.P Pool Motor Square Flange 56Y Up Rate (B852, B2852) and the 1 H.P Pool Motor Square Flange 56Y Up Rate - B853 are comparable motors. Please view our How To Understand True Pump Horsepower - Up Rated vs Full Rated guide. Please do not forget the Tune Up Kit Pentair/Purex Whisperflo Saltwater - GOKIT32SALT or the shaft seal when replacing the motor. The How To Wire A Pool Pump will walk you through the wiring.
Reply
My motor hums but does not start. Any suggestions other than replacement? If I need to replace a Pentair model SF-n1-1a part #340038. What are the choices and what is the advantage of each? Thanks
Reply
Hi, Thomas. You will need to test the capacitor using our How to Test a Pool Pump Capacitor. If the capacitor fails, then it will need to be replaced. If it's okay, then you can check the windings using our How To Use a Multimeter to Test a Pool Pump Motor - Winding Resistance. Your options for replacing the motor is this PL2853 (standard), B2853 (standard) or B2661 (energy efficient). You will also need the Super Flo Tune Up Kit - GOKIT78.
Reply
Will this motor work for a Sta-Rite Supermax, Pump model number PHK2RA6E-102L? It is a 1.0 hp / 1.25 SF motor with a square flange. The motor number is 196249. Thanks!
Reply
Hi, my pentair whisperflo is working but making a screeching noise. I guess I have to replace the motor. Will this work to replace wfe-4 011513
motor-#177450
OR is there at 1.5 HP motor that would be compatible? Thank you!
Reply
Hi, Danielle. This PL2853 will not work as a replacement, you will need the B2841V1. You will also need the Pentair/Purex Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT.
Reply
i have an aqua tools pump motor 1 hp that i need to replace part # AT2310210 i cant find one . is there a replacement for this
Reply
Hi, Jeff. This motor will not fit your pump model. If you can provide a picture of the motor label I will be able to locate the correct replacement motor.
Reply
Need to replace polaris booster pump motor. It says: 3/4hp, 3450 rpm, 230/115 volts, sf 1.65, model # c55cxkrl-2079 & flange/frame 48y. Do you have one that will be an exact match, or an energy efficient model that will fit my current plumbing?
Can you tell me if this motor will work as an a replacement for attached pic?
Can you tell me if this motor will work as a replacement for attached pic?
You will actually need the PL2854 1.5 HP Up Rated Replacement Motor as you current motor is a 1 HP Full Rated Motor which is equivalent to a 1.5 HP Up Rated motor. To explain this it easiest to show the math which I will do so here 1 HP Full Rate x 1.65 Service Factor = 1.65 True HP. 1.5 HP Up Rate x 1.15 Service Factor = True HP of 1.65
Reply
Is this the correct replacement pump motor (see attached photo). Also, can you tell me what is the correct tune-up kit.
Hi Joe, Yes this is the correct replacement motor for the B2853 motor in your photo. Could you confirm the make and model of your pump so we can suggest the proper tune up kit? Common pump names would be Pentair Whisperflo, Jandy Stealth, etc.. It looks like you may have a Whisperflo and if so the tune up kit is this Pentair Whisperflo Tune Up Kit.
Reply
I have a Jandy FHPM 1.0 single speed pump working at 1.00x1.24=1.24 total motor HP. Will this motor mate up and work correctly? Thanks
Reply
I need to replace our old Marathon pump motor (model #5KC38SN6C84AX). I have attached a photo, but the tag is weathered. Also, what tune-up kit would be appropriate?
Hi Joe, Could you also supply a photo of a wide shot showing the entire pump including where the pipe goes in and out of the pump? Simply click the reply link on this page and upload the photos.
Reply
Reply would not let me add photo
Hi Joe, Could you post one more photo of a close up photo of the silver model # label located at the top of the black round seal plate near the band clamp. The way you posted this picture will be fine. Also if you could supply the model information from that label in text format in your reply that would be very helpful. I think this should be the last piece of information we need to make the proper reccomendation.
Reply
Hello is this the same motor? I need a capacitor for the motor in the picture and am having trouble finding that part number?
Hello, Can you please send a side view picture of the entire pump? We will need this in order to find the correct motor replacement for you. This will be the correct capacitor you will need, http://www.inyopools.com/Products/07501352014036.htm
Reply
Was looking at this pump to replace the one in attached picture but have no idea what brand pump I have. Stickers have faded too much. Can you tell from the picture so I can order the correct trim kit.?
Hi, John. This PL2853 motor is a direct replacement for your Pentair / Pac Fab Challenger Pump.
Reply
Will this replace my 0-193995-07?
Hello, This will be the proper motor you will need for your pump.http://www.inyopools.com/Products/00200017039439.htm
Reply
Can you tell me what motor and tune up kit I need to replace this motor on my Pentair whisperflo pool pump
Hi, Barry. This PL2853 motor along with the Whisperflo Tune Up Kit - GOKIT32 or GOKIT32SALT are the parts you will need for your model pump.
Reply
Why would you need to change to 115 volt
Reply
Hi Barry, You would have no need to change to 115V this motor just has the option to wire 115V or 230V based on whichever power is available to you at the equipment site.
Reply
My motor is humming and won’t kick on. It’s 7 years old so needs to be replaced. What motor do you recommend? Thanks!
You can use this PL2853 or the B2853 as single speed motor replacement options.
Reply
Hi Tony, Yes this PL2853 motor would be the proper replacement motor for your motor in the picture. When replacing your motor we would also suggest a Tune-Up Kit but to be able to suggest the proper Tune-Up Kit we would need a photograph your entire pump, a wide shot showing where the plumbing goes in and out of the pump. To send us photos simply click on the reply link below and upload your photos.
Reply
Here is the full pump
Tony thank you for that photo it was quite helpful. You have a Pentair SuperFlo and you will also require this SuperFlo Tune Up Kit
Reply
Thanks so much! So I don’t need to buy a new pump and all that? This other company is trying to tell me I need the whole thing. I’m just going to buy the motor and the tune up parts. Don’t see need to buy whole pump and motor.
Reply
Hi Tony, No you don't need the complete pump. The humming is a bad capacitor in the motor and a motor replacement with Tune Up Kit will get you back up and running. Here is a Video on How to Replace a Pool Motor which should be helpful when you tackle this project. The only side note is that if you live in California you will need a variable speed motor if you live any other state than this single speed motor will be fine.
Reply
I need to replace the motor on my Pentair Superflo. Would this motor work as a replacement?
Reply
Hi John, This is the proper motor for a Pentair Superflo but we would need to get a photo of your motor label to make sure that you are getting the proper HP. To send a photo simply click on the reply link below to upload your photo(s).
Reply
I am ordering this pump but need a new compression elbow for the wiring. Can you tell me if you have an elbow that will fit this and 1/2 flexible conduit.
Reply
Hi, Melinda. We do not carry those conduit elbows. You can purchase one at your local hardware store.
Reply
Searching for replacement motor and seal for in-ground pool.
Original motor. Hayward. SP2800X Series - Max-Flo 1hp. Model SP2807X10. Motor SPX1607Z1M.
Current motor. 1 HP GI Maraton Motor and 201 Seal.
Reply
Alan, the PL2853 will not work as a replacement for your SPX1607Z1M. The PL2853 is a square flange motor your SPX1607Z1M is a round flange. Yor replacement for the SPX1607Z1M, would be the A.O. Smith 1 HP Round Flange 56J Up Rate Motor - UST1102. The shaft seal for your SP2807X10 pump would be the Pump Shaft Seal 3/4", Generic - PS-201.
Reply
trying to replace marathon inground pool motor model #5kc38sn6084 amp 50,cat#c1245 rpm 345,sf125,hz60,se#109j2,v115/230,code m,thank you tony
Reply
I would like to order a replacement Motor for my Jandy 1hp PlusHP pool pump.
The following is all the info I have:
P/N 7-193985-04 RPM: 3450 Frame: P56Y Volts: 230/115 AMPs: SF 7.1/14.2 Enc: DP Time: Cont 1081 Pool mount Horz with vent holes down. Mod: # 193985 CPN: #A0582907 Ser: 08516H2ML050000414 (Century Centurion)
Can you Help Me?
I would like to order today if possible (Free Shipping?)
Please email info asap
Thank you so much and warm regards.
Bill
Hi William, This is the correct motor for your pump, we would also suggest this Jandy Shaft Seal when you replace your motor. If you order right now and reply back with your order # we will try our best to get your order shipped out today.
Reply
Thank you for your prompt reply. Yes, I would like to order today. How much is the shaft seal? Maybe I do need one, but the current seal shows no sign of leakage, but may be good to have on hand.... so, how do I order? Thank you - again warm regards - Bill
Reply
Hi Bill, To order the motor click on the add to cart button above and to order the shaft seal click this link here http://www.inyopools.com/Products/07501352058887.htm the price for the shaft seal is $25.99
Reply
I need to replace my Hayward electric motor on my pool pump, the model # is C48K2H143B1, can you give me info. on which one i need with price.
Thanks in advance.
Reply
Hi John, That part # is not pulling up in our system. Could you click the reply link below and supply the information from the motor label like... HP, Amps, Frame, SF, Volts, RPM, etc.. Also if you could let us know the make and model of the pump common names are Hayward Super Pump, Power Flo, Matrix, Max Flo, Tri-Star, etc.. Or if you want to send us a few photos they are always helpful, one close up photo of the motor label and a second wider shot showing the complete pump including where the pipes go in and out of the pump. To supply the photos simply click on the reply link below.
Reply
I have a .75 HP Pentair Whisperflow pump that is dying. I've never been satisfied with the suction on the skimmer furthest away from the pump and would like to replace my .75HP motor with a 1 HP motor. Besides having to upgrade the impeller would the rest of the pump housing be compatible?
Current motor: 071313 Current Empeller: 073127
Reply
Hi Chris, Since your current motor is a Full Rated 3/4 HP which has the same True HP as a 1 HP Uprated motor, this would mean you need to upgrade to a 1.5 HP Up-Rated Motor to see an increase in power for your pump. This would mean you would require the PL2854 1.5 HP Up Rated Replacement Motor and this 1.5 HP Up Rated / 1 HP Full Rated Whisper Flo Impeller and this Whisperflo Seal Kit. This would be all you need to upgrade the HP. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
What is the difference between the Pureline PL2853 (139.99) & the AO Smith B2853 (157.99) motors? I see one has a 2 yr warranty vs 1 yr on the other and there is a difference in amps. What does a lower amp rating, PL is 5.7/11.4 and the AOS is 6.6/13.2, mean in regards to operation of the motor?
Reply
Essentially they are the same motor style, the B2853 but made by two different manufacturers. The lower amp rating means it costs less to operate.
Reply
This is the model you suggested for me to replace my old motor. I hooked it up and it runs for about an hour and stops and is super hot to the touch any ideas?
Reply
Hi, could you post a few photos showing how the motor is wired, also are you wiring for 115V or 230V? To supply photos simply click the reply link below and upload your photos. Once we receive the photos we will make the proper suggestions.
Reply
I need to replace my pool pump motor. It is 2 speeds ,but i never use the low speed. It is a Sta Rite Supermax Pump #PHK2RAY 6E 102L 1hp AO Smith motor230V RPMs 1725/3450 Square Frame.Can u give me a replacement motor .Possibly Purline PL2853. Will that motor work?
Reply
I have a A.O. Smith Century B2853 1HP 115/230V Square Flange Up-Rate Pool Motor PHK2RA6E, that starts to be very noisy, does your PL2853 will be a direct fit if I purchase it? also, what tuning kit will fit the PL2853? Is the Amp difference between B2853 (SF 6.6/13.2) & PL2853 (5.4/11.4) will cause malfunctioning?
Thank you
Reply
Yes, the PL2853 is a direct replacement for the B2853. This is your gasket kit: Pentair SuperFlo/Sta-Rite SuperMax - GOKIT78
Reply
My motor recently started running quite a bit louder than normal. It's a Century Model #193985XCN/Jandy Pro Series. I think this is the proper replacement pump (this one or or the AO B2853). I also think you would recommend the Jandy Shaft Seal (Jandy Part #5020-087) but just want to make sure I am looking at all of this correctly. Thanks for your help! Kevin
Hi, Kevin N. This PL2853 motor is the correct replacement. However, I'm unable the confirm if the Pump Shaft Seal 5/8" OEM - R0479400 would fit without knowing the pump housing model and serial number.
Reply
Lennox - thanks for the quick reply! It looks like it is a Jandy FloPro Model #FHPM1.0. If you could confirm the right shaft seal, that'd be great!
It looks like it's a Jandy FloPro FHPM1.0.
My pool pump is making noises, almost sounds like its grinding. Sometimes it just stops working and gets very hot. (AquaTools Pump AT2310210) Motor S48L2A40B1. what is the best steps to take.
Reply
Hi, Dave K. The best steps to take is to replace the motor or the entire pump. Please provide the pictures so that we can recommend some replacement options.
Reply
Hi I need to replace my 1 hp motor would this be a proper replacement?
I have a Sta-Rite Super Max pump model PHK2RA6E-102L and I need a compatible replacement motor. Can you point me in the right direction?
Will this motor fit a STA-RITE pump model PHK2RA6E-102L?
Reply
Yes, the PL2853 1-HP Square flange is compatible with the Super Max 1HP Pump - PHK2RA6E102L.
Reply
I need a replacement motor for Pentair Superflo series 34-0038 Self Priming Pump Serial #1/11/B08
Will I need a seal kit? I know when I replace a Hayward or a Pentair I always use a seal kit.
Thanks
Tony
Reply
Yes, we recommend using a seal kit and in order to confirm the correct one we would need the model name or number of the pump housing that the motor is attached to. If you are not sure of this you can email images of that to upload@inyopools.com so we can confirm and further advise.
Reply
Do I need to order a bearing and seal kit with this motor?
Reply
You will not need a bearing with this motor but we do recommend replacing the seals and gaskets but we would need to know the model name or number of the front pump housing that the motor attaches to. If you are not sure of that you can email images of that to upload@inyopools.com so we can further advise.
Reply
Will this motor work for my pump? And what seals do I need to replace?
Reply
Hello, I can confirm this for you. Can you please send a side view picture of the entire pump and a picture of the motor label?
Reply
I have an a.o. smith b2853 1 hp motor with a 56Y frame....I need an end bell cover that would fit...can you help?
Hi, Michael. Our extensive parts database does not list the Shaft End Bell for the B2853 motor.
Reply
My pool motor is defective and stuck in the seal plate. I also need to figure out what Horse power my current motor outputs,
.please see attached photos for part numbers.
Please confirm part numbers for motor, seal plate and other parts to reassemble my pump.
What is the expected life of a challenger pump? My motor has seized up and the unit was installed 11 years ago so debating on replacing the whole pump/motor assembly.
Reply
So that will really vary on maintenance, however, I would say on the average of about 15-20 years. If the housing isn't warped from heat, cracked or leaking then they can last a very long time.
Reply
I need a replacement motor for a Challenger pac-fab pump
Reply
So if you type in your motor model, part or catalog number in our search for an item part on the top of our web site your motor options should come up as results. You can then select your motor and confirm that your model, part or catalog number is listed in the products alternate part number list in the product details.
Reply
Is this the correct motor I need? It's a sta-rite pump, square flange. thank you
will the PL 2853 work on a flotec at251001-01 and pump no c48j2pa105c2 at 5.7 amps why is it less expensive than uqc 1102
Reply
Is this Motor a Replacement for the 1 HP that is on The Pentair Model #340038 ?????
Reply
Will a Pureline PL2852 replace a Jandy Stealth SHPM? It yes which installation kit is used?
Reply
Jerry, in order to suggest a replacement motor we will need more information on the existing motor. What is the model, part, or CAT number of the existing motor? If you are unable to locate this information, please send me a photo of the large white motor label on the side or top of the motor to upload@inyopools.com.
Reply
hi, i will like to replace my motor if possible with a variable speed if possible, i dont know if it can be done or i need to stay with a single speed, i have a centurion or AO Smith cat B2853 part 7-F56AA37A01-04
also im not too handy so hopefully dont have to update any electrical wriing.
thx in advance
ramon Veras
201-852-0449
Reply
Hi Ramon, The variable speed replacement motor for your motor part number F56AA37A01 is the ECM16SQU. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Will this motor fit a Waterway model C55CXKLS-5006
Reply
Hi, Jeff The correct replacement motor for your C55CXKLS-5006 is this USQ1102 1 HP Replacement Motor and Not the PL2853. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
