Part # B854
Warranty 1 Year
Manufacturer Code B2854
Dimensions 8" L x 6.5" W x 13" D
Alternate Part #'s 0-193986-24, 0-F56AA40A01-24, 10-177216-24, 1103665400, 13773, 168453, 177216, 177475, 177972, 187333, 193986, 193986XCN, 196239, 196250, 355022S, 355023S, 355340, 54004, 5KC39UN6086X, 5U125, 7-177216-24, 7-193986-24, 7-F56AA12A04-24, 75234, 8-177216-24, 90106931, A0582908, A100FL, A100FLL, B2854V1, B693, B854, BPA450V1, C1246, C48L2EB103, EB854, F56AA40A01, F56AB32A01, F56AC20Z01, K63CXEAP-5221, K63CXERY-4786, o-193986-24, P718, SP3210Z1M, SQ115U, SQD15UP1, USQ1152, V54004, AOSB2854V1, CRMB2854V1
Century B2854 Details:
A.O. Smith Centurion replacement motors for Pentair WhisperFlo, energy efficient, full rated pumps. Specifications: HP = 1.5, RPM = 3450, Voltage = 115/230, Amps = 16.0/8.0, Service Factor = 1.10, Frame = 56Y, Shaft = Threaded.
Note: NOT California Title 20 Compliant.
California Title 20 Compliant Options:
What is Service Factor?
Reply
Service Factor(SF) is a multiplier that when multiplied by the horsepower of the motor indicates the total permissible horsepower loading that may be carried when the motor is operating at rated voltage and frequency. The most important thing to remember when replacing a motor is that the replacement motor's horsepower times its service factor must be equal to or greater than the original motor's horsepower times its service factor. The Service Factor rating can be found on the motor label. See Step 4 of our How to Read a Pool Motor Label guide.
Reply
Why do I need to purchase a new shaft seal?
Reply
We strongly recommend replacing the shaft seal. The purpose of a shaft seal is to prevent water from running down the shaft of the motor and into the motor housing. Water will damage the bearings and cause the motor to fail. A new shaft seal should be installed whenever a motor is replaced. The motor manufacturer can deny the warranty if the motor fails to due to water damage from a faulty shaft seal. To find your shaft seal you will need to visit our Pool Pump Parts Page or the Spa Pump Parts Page and select your make and model.
Reply
Why should I purchase a Tune Up Kit?
Reply
A Tune Up Kit includes all of the essential replacement seals and gaskets for the pump. The seals and gaskets should be replaced when installing a new motor on your pump. New seals will prevent the pump from leaking water or losing the prime. A Tune Up Kit will protect your motor and ensure that the pump is working efficiently.
Reply
What are the dimensions on the shaft bearings or a part number and do you sell replacements?
Reply
The correct replacement bearing is part number 5270-31. The motor would require two. Here is a link to the bearing.http://www.inyopools.com/Products/07501352012909.htm
Reply
2 to 4 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench
5 0
1. Watched DIY videos to learn how to install it properly.
2. Turn off the breaker. I took out the pump and the motor together.
3. Took off the motor. Bagged the bolts since there where to different sizes.
4. Took off the power cord, and motor accessories.
5. I built a new power cord. The original was old and weather beaten. I took it to the home store and bought the same parts. Get the proper gauge cord and a new plug. I disassembled the old plug to learn how to assemble the new one. It was easy.
6. Installed the new seal based on the old motor. Simple, but work slowly.
6. Reinstalled the motor blade. Don't over tighten it. Make sure it spins properly or it could bind. Install the safety screw.
7. Installed the pump plate and new seals. I sprayed them with silicone before install.
8. Mate the pump and motor. This is why I took them both off. It's easier this way to ensure the new seal doesn't slip off causing a leak. I put the pump on end and slid the motor in place.
9. Tighten the bolts evenly. Do not over tighten or you could crack the pump plate.
10. Wire the new power cord. I took a picture of the old cord on the old pump and installed the wires the same way.
11. Make sure the plumbing to your pump is on correctly. Do not over tighten.
12.Turn on the breaker.
13. Turn on the pump.
This took me 3 hours or so. I took my time and went step by step. I used the old motor as a guide. I took pictures to use as a reference. Doing it myself saved me 500 dollars. The local pool place wanted 1300 or so to do the job. Plus they wanted 300 more for the motor. It's worth trying to DIY.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
Once I received my new motor from INYOPools I replaced the old motor. With the help of videos it only took approximately 1 hour to change the motor and get my pool back up and running. Ordering was easy and shipping was quick which helped keep my pool water from turning green.
1 to 2 hrs
Screwdriver, Socket Set, Adjustable Wrench
2 0
1. removed bolts that held motor to pool pump.
2. removed impeller from seal plate
3. removed seal plate from motor
4. placed new seals on impeller and seal plate
5. attached seal plate to motor
6. attached new motor with seal plate to pump housing
7. reconnected electrical wires and ground wire to new motor
8. turned electicity back on and flipped switch to start the motor
9. water from pool started flowing through pump
Less than 1 hr
Screwdriver, Nut Drivers, Pliers
2 0
Less than 1 hr
Nut Drivers
1 0
Less than 1 hr
Screwdriver, 9/16 wrench.
After turning off outside and main panel breakers wiring was removed and motor seperated from pump. Pump was bolted and wiring replaced to refreshed pump. (new diffuser and impeller) Servicing section of Challenger instructions for my pump were very helpfull. Down loaded from their web site.
Less than 1 hr
Socket Set, Adjustable Wrench
1 0
Less than 1 hr
Screwdriver, Socket Set, Wrench Set, Adjustable Wrench
Took a picture of the old ID tag. to make sure I had the right Frame and motor size. Turned off the electric at the power box. Drained the water and seperated the pump fan and seal area. cleaned all the debris out. made sure I had the correct. seal and bushing. reassembled. lubed the outer o ring area. tightened the flange mount. added water. then purged the air. Checked for leaks and none were found.
1 to 2 hrs
Screwdriver, Pliers
I ordered the replacement pool pump motor. Once delivered, I removed the existing motor from my pool pump. Then I installed the new pool pump motor. Once installed, I powered the motor on. It ran perfectly and silently. I have had no issues with this motor since I installed it.
Less than 1 hr
Screwdriver, Nut Drivers, Adjustable Wrench
0 2
Found a comparable pump motor and best price at INYO Pools. Pretty easy to swap out.
Shut off all power and remove ground and 3 wires from pump
Remove 4 9/16th bolts and remove motor
Remove the diffuser, impeller shaft seal and seal plate - screw driver and crescent wrench
install in reverse order on new motor.
Lube all O-rings and reinstall onto base.
Less than 1 hr
Screwdriver, Socket Set, Wrench Set, Adjustable Wrench
We removed the pump assembly from the PVC pipes. We were fortunate that the bolt holding the pump impeller and the pump motor was not frozen. We removed the 4 bolts holding the pump housing to the motor and then were able to use a wrench to hold the long shaft bolt while we turned the impeller counterclockwise. Once we were able to break this bond, the assembly was simple. Attached the new motor to the impeller and then attached the housing to the motor with the 4 bolts. We then reattached entire assembly to the PVC pipes and turned on the pump. Ran perfectly. Total time was less than one hour.
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set
Ordered the new pump to match the old one per the label. It arrived as shown and promised. I replaced the old pump motor with the new, it was a perfect match and when I turned it on it was nice and quiet with no issues!
1 to 2 hrs
Screwdriver, Socket Set, Wrench Set, Adjustable Wrench, Both Phillips and flathead screwdrivers are needed
6 0
After watching the Inyo videos for replacing a pool pump motor and replacing the shaft seals several times (which are both excellent step-by-step videos), I also searched YouTube and found a video on replacing a Jandy pool pump motor specifically. I'm glad I did because my Jandy PHPM pump had a few more steps to do than the Inyo video that used a Hayward pump. But together, these videos made changing the motor and shaft seals relatively easy. I was worried that after replacing the motor and the shaft seals myself, I would be turning on the new motor and watching a new water leak. But I was pleasantly surprised and relieved of my worries when that didn't happen. The new motor runs smoothly, incredibly quiet compared to my old failing motor, and without any leaks. As an additional note, the shaft seals are easy to replace (no special techniques) and the electrical wiring (230V from a double breaker for this motor) to the new motor was totally simple - two black wires to the two uncolored leads and one green ground wire to the green colored lead - that's it! No chance of screwing it up!
Less than 1 hr
Screwdriver, Pliers, Socket Set
1 0
first turned off power to motor, drained the basket housing
disconnected the electric wires from the motor, black, white and ground
unbolted the motor from the base and placed it all on the table
unbolted the impeller and housing form the motor, inspected the ceramic bushing.ring & orings
bolted new motor to impeller housing, bolted back to base, hooked up electrical wires and piping
turned on and perfect, purrs like a kitten
Less than 1 hr
Screwdriver, Pliers, Socket Set, Adjustable Wrench
2 0
I tried replacing the Start Capacitor but that did not resolve the problem
I then shut off the breaker and disconnected the power lead.
I disconnected the plumbing connections and removed the pump
I have a Jandy filter, so the first step was to removed the basket housing. 8 bolts
I then remove the impeller housing . two small screws. Note the arrow on the covers for reassembly
I them removed the impeller screw. Note: it is reverse thread, and you will need to hold the motor shaft to remove the screw.
I then removed the housing plate to the motor. 4 bolts. The seal is held in by this housing so note how it is installed prior to removing the seal.
Installation was the reverse of the step I described. Always use a new seal.
Took about 45 minutes
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Wrench Set, Adjustable Wrench
4 0
Noticed old pump was very noisy. Checked and could hear bearings failing inside motor. Checked local pool supply store , they where trying to sell me complete new pump assembly. Being the craftsman that I am I got on Inyo website found the correct pump motor. Had it to my home in a couple days. Removed old pump motor. Installed new pump with new seals and gaskets. Fit was perfect. Wired motor up. Flipped the switch and works great. Pool circulation is better than ever and super quiet.
2 to 4 hrs
Screwdriver, Socket Set, Wrench Set
3 0
Disconnect electrical wires. Remove 6 bolts from impeller, and remove. Then remove 4 bolts from motor, and remove motor.
Replace gasket and shaft seal on impeller. Replace gasket on the housing of motor, mount impeller to motor and replace bolts for impeller and motor.
Connect electrical wires and turn power on. Check for leaks.
1 to 2 hrs
Screwdriver, Socket Set
2 0
I have two identical pumps, one for the swimming pol filter and the other for a waterfall feature. The waterfall pump stopped working an would buzz when I turned it on. I initially replaced the capacitor which helped a little as now the motor would spin for a while and then stop.
I suspected a bad bearing. I tried finding a replacement via Hayward but had no luck searching for the pump model number I found INYO and ordered the pump. When t arrived I replaced the bad pump with the new model wired it up and all is now working. Great price and confidence in a perfect match.
1 to 2 hrs
Screwdriver, Wrench Set
2 0
Less than 1 hr
Screwdriver, Socket Set, Adjustable Wrench, Volt meter
1 0
1.Turned breaker off powering motor
2. Tested motor to make sure there was no power
3. Unwired motor and removed from pump
4. Changed out all o rings and seals and reinstalled new motor to pump.
5. Wired motor back and turned on power and checked voltage
6. Pour about 5 gallons of water in pump seal up and turn on motor should take a few seconds to prime and should be good to go
2 to 4 hrs
Screwdriver, Socket Set, Wrench Set
2 0
1 to 2 hrs
Screwdriver, Pliers, Socket Set, Adjustable Wrench
3 0
Made sure 3 times the breaker was off
Took off the housing bolts and pulled existing motor away from the pump.
Cleaned the impellor and wiped down all the parts going back with the new motor and also made sure to clean the electrical cord going to the new motor to be able to make a clean connection.
I then added the new gaskets and put the motor with the pump connected the wires and tested it. Tt worked great! It took some time but with some wd40 and towels to wipe things down it makes it a fast clean job.
Less than 1 hr
Screwdriver, Socket Set
1 0
Pretty simple. I took the old one off, put the new one on. Took the wire connections off along with the four motor mount bolts and that was it! It is a really quiet motor! Worked great, easy ordering! Best price around!
1 to 2 hrs
Screwdriver, Pliers, Wrench Set
7 0
purchased new motor (I had new gasket and seal on hand) and replaced. it took a total of 2 hours with basic tools. this new pump motor is so quite I have to keep checking on it to see if it is running... It has been on-line now for over a month with no problems. I would be somewhat lost if it weren't for watching the "how to" video. thanks.
The Most Helpful Review
43 6
(5 out of 5 stars) Pool Filter Motor
Reviewed By: DreamBigGoGreen from Bowie, Maryland ()
Pros: Customer service, shipping time, price and product
Cons: None that I can think of
Best of all is the wonderful customer service help provided by Inyopools. The product was here in the time specified and the price was considerably less than the 5 other companies I checked with first. The product was as specified and ordered and hasn't given me any problems to date. It was installed about a month ago.
Was this review helpful to you?
The Most Recent Reviews
(5 out of 5 stars) Stop searching for a pump motor and buy this one!
Reviewed By: Inyo Customer ()
Absolutely perfect fit, runs quiet and smooth. If you need to replace your Penatir Superflo motor, or probably any pool pump motor, contact Inyopools.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Runs smooth and extremely quiet. Was able to easily make correct selection from online Website. Replaced Waterway motor. Was shipped free ground service UPS & received in 5 days. Perfect fit and easy to swap out end to end.
Was this review helpful to you?
(5 out of 5 stars) Pump Motor Replacement
Reviewed By: Inyo Customer ()
the motor is fairly easy to install. A one-man job. After viewing the DIY videos, the installation took about 3 hours. It would have been just two, but I had to make it more difficult than it had to be. Had an issue with the reassembly that occurred due to my failure to adequately document the disassembly of the diffuser and impeller assembly. Totally on me. That being said, the motor has performed well.
Was this review helpful to you?
(5 out of 5 stars) Pool Pump Motor Replacement
Reviewed By: Inyo Customer ()
Researched how to change a burned out motor on the INYO Pool website. Very easy to look up the exact motor I needed along with the shaft seals. Ordered the motor and seals on Dec 20 and everything arrived on the 24th. Took 1 hour to replace the motor and saved myself $300.00 by not calling a pool service.
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Great deal on this motor!
Was this review helpful to you?
(5 out of 5 stars) Great Service
Reviewed By: Inyo Customer ()
Perfect Pump, easy order, fast delivery, easy assembly!
Was this review helpful to you?
(5 out of 5 stars)
Reviewed By: Inyo Customer ()
Nice motor. Super quiet.
Was this review helpful to you?