Is the UST1202 the replacement motor for my 2HP Hayward Super II pump? My motor does not have that external bump. Does that make a difference?
Reply
Hello Doyle - The UST1202 is the correct motor if the service factor (SF) of your current motor is 1.1. This rating can be found on the motor label. The external bump is a run capacitor. All of the new 2HP motors have this capacitor.
Reply
Hello: I currently have a Hayward Super II pump, with a 1 1/2 HP motor, I would like to upgrade to a 2HP motor. The pump model is SP3010X15AZ.
Will this 2HP motor work properly?
Thank you
Reply
Hi Frank, This would be the correct motor if you would like to upgrade to 2 HP but you will also need to upgrade to a 2 HP Hayward Super II Impeller as well as upgrading to a 2 HP Hayward Super II Diffuser.
Reply
My existing motor which I want to replace is a AO Smith UST1202 2 HP, SF1.0. Can I replace with the similar make with a SF of 1.1?
Reply
I have a Super ll pump. The model number is partly there it starts with K48N2..the rest is not readableand I think the serial number is well part of it is SP-1620-Z1BF...can't figure out the last letter. can I replace with this pump?
Reply
Hi Tina, Yes the UST1202 would be the correct replacement motor for your Super II. The part # you supplied of SP-1620-Z1BF confirmed this. I would also suggest a Hayward Super II Tune up Kit when replacing your motor. We also have a good Video on Replacing a Pool Motor which should pretty helpful when you do this job.
Reply
I need to replace the bearings on this motor. Which bearings do I need for the front and which do I need for the back? Thanks!
Reply
Hi Paul the UST1202 motor requires One 6203 Bearing and One 6204 Bearing.
Reply
How much would it add to the cost to use a 1.5 hp motor rather than the 2 hp?
Reply
Elwood, You can calculate the cost with our How To Calculate the Cost of Running A Pool Pump step-by-step guide.
Reply
We install a new motor & is pumping the water the oposite direction.
What should be the rotation of the motor ?
If these is not the cause what could be ?
Reply
Hi Edgar, When looking at the motor from the front it should turn in a counter clockwise rotation.
Reply
Hi,
What's the filtration rate for this pump? I'm wondering how long I have to keep it on to clear my pool one time (about 25,000 gallons) per day. Thanks!
Reply
Nick, Replacement motors do not have a filtration rate. That would be determined by the pump housing model number.
Reply
Hello, I am replacing a Hayward super pump II / A.O. smith, model #K48M2N111 (SP-1615-Z-1-MEG). Is this model the direct replacement for it?
Reply
Hi John, Yes this is the direct replacement for your Hayward Super II model #K48M2N111 (SP-1615-Z-1-MEG). We would also suggest a Hayward Super II Tune Up Kit when replacing your motor.
Reply
What special tool will i need to replace a motor?
Reply
Hi Pat, No special tools are required to a replace a pool motor. We have a great Video on How to Replace a Pool Motor which will walk you through the exact step by step process for motor replacement.
Reply
Will this motor be the proper replacement for the motor in a Hayward 2hp pump model sp4020ns? Thanks.
Reply
Hi Bill - No. USN1202 is the proper uprated replacement motor for the Hayward 2hp pump model sp4020ns. See the Service Factor (SF) on the label of your current motor. If it is 1.2 you have an uprated motor. If it is 1.35, you have a full rated motor and you would replace it with SN1202.See our guide on "How To Understand True Pump Horsepower - Up Rated vs Full Rated".
Reply
im looking for a motor for my pool pump Hayward ( sp32202EE)
Reply
Hi Jose, You can use the 2 HP Dual Spd. Motor - Full Rate (B984, B2984) or the 2 HP Full Rate Dual Speed w/ Digital Controller Square Flange Motor (B2984T) as replacement motors for your Hayward SP32202EE Pump.
Reply
I need Hayward Super II motor replacement. the model is c48m2n111a3. Please direct me to the correct model replacement. thanks
Reply
Hello John - Part number UST1202 is the correct motor replacement for your c48m2n111a3.
Reply
I am looking to replace the pump on my Hayward Super Pump (C48M2N111) with the UST1202. Which impeller would I purchase to go along with this pump?
Reply
Hi Mike, The A.O. Smith 2 H.P Round Flange Up Rate Motor (UST1202) will be the correct replacement for the C48M2N111 motor you currently have. The Hayward Super Pump Impeller (SPX2615C) will be the matching impeller. I would recommend getting the Hayward Super Pump Tune Up Kit (GOKIT3).
Reply
Hi - is this the correct replacement motor for a Hayward SP261X20?
Thanks!
Reply
Scott- The part number provided is incomplete, if you mean that you have a SP2615x20 Super Pump, the A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor (UST1202) would be the correct motor. I would also suggest getting a tune up kit which would be gokit3.
Reply
Need motor , old motor is k48n2111 , 2 hp. with a filter # sp2615x20. What will I need ?
Reply
If the model of your complete pump is in fact sp2615x20 then this UST1202 motor is the direct replacement.
Reply
I have the Hayward SP3015X20. I intend to buy the A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor (UST1202).
Please confirm that this is the correct motor configuration for this model pump. Which gasket kit should be ordered with the motor?
Reply
Hi Greg Yes the UST1202 will be the motor for the SP3015X20. Also the tune up kit needed will be GOKIT2
Reply
what is the replacement motor for this PUMP?? Hayward super II pump, A.O.Smith model # K48N2N104 typeUAK 2 horsepower 230volt 10 amps 1.25sf 3450rpm
thank you
Reply
Toni,If your replacement motor part # is K48N2N104, then your replacement motor is ST1202 and not the UST1202.
Reply
Is this (2 HP UST1202 Replacement Pool Motor) the right replacement for
AO Smith
Model # C48M2N111A3
SF 1.0
FR 56J
HP 2.0
115/230V
21.6/10.8 Amps
Reply
Hi Mario, This motor will be the correct replacement base off of the info provided.
Reply
I have a Jaccuzzi Magnum Pump Model 2MF-S2 (order no. 94026120) with a MagneTek 2.0 HP Motor Part No. 8-184951-03. I need to replace the Motor but have no clue whether the AO Smith 2 HP or 2.5 HP Motor is compatible. Please advise which Motor is correct. With the new Motor, what other Parts should be required to ensure motors can be swapped out and quick start up?
Reply
Hi Roger, The B809 would be the correct replacement motor for Part No. 8-184951-03. I would also recommend getting the Jacuzzi Magnum Tune Up Kit (GOKIT14).
Reply
I have a Hayward SP 1615 -Z1-MBK 2 hp pump with a C48M2N11A3 Motor S/n 7L96 that i need to replace the motor. Can you tell me which motor is correct? On the motor name tag last digit is obscured and could be an 8 rather than a 3.
Thanks,
Steve slater
Reply
I have a Hayward 2hp Northstar pump motor sp1615z1mnsc. Wich is the correct replacement motor.
Reply
Hello Jason, The correct replacement motor for your Northstar Pump will be the A.O. Smith 2 HP Up Rated Northstar. We highly recommend you replace your seals with the HAYWARD NORTHSTAR/TRISTAR SHAFT SEAL anytime you replace your motor.
Reply
Can I use this 2HP motor to replace a Model C48L2N134B1 1 & 1/2 HP on a Haywood Super Pump. The existing C48L2N134B1 is frozen and needs to be replaced. So in the process I'd like to get better flow by upgrading to a 2 HP motor. Thanks in advance for your help.
Reply
If you did change from a 1-1/2HP to a 2HP with the super pump you'll have to replace the impeller as well because the motor will be too big for the impeller. Also you'll need to know the flow rate of your filter and foot of head to see if your filter will even be able to handle the increased flow rate.
Reply
We have a Hayward Pool pump with an AO Smith motor (K48M2N111). Can I just swap it out with the UST1202 and how difficult would it be?
Reply
Hi Tony, Yes you would just swap out your motor with this motor. Here is a Video on How to Replace a Pool Pump Motor which should give you a good idea of what is involved in the replacement (it is pretty easy). We would also suggest a Hayward Go Kit when replacing your motor.
Reply
I have a Hayward motor super II pump, model K48NZN104, HP2.0, SER 8D07, Volts 230, RPM 3450, AMPS 11.2.
It gets hot and I was recommended to get a new one model T55CXCJM 1347, HP2, Volts 230, AMPS 10.0 and I did but it also gets hot after 10 minutes disconnected from the pump. Can you tell me what the problem is please?
Reply
Hi Felipe, Could you let us know the S.F (Service Factor) for the old motor and for the new motor. This will be listed on the label which is on the motor, if you don't have this for the old motor that is fine, but I would need it for the new motor to try and troubleshoot your issue.
Reply
I'm downgrading an SP 1615-Z1-MEG to run with a 1 HP motor. What impeller model should I get? The original impleller fits fine, but I obviously don't want to use a 2 HP impeller with a 1 HP motor. Also, Is it ok to use the same diffuser?
Reply
Hi, We will need the model of the pump housing in order to locate the correct impeller needed and to find out if the same diffuser can be used for the 1 HP motor.
Reply
I am looking for a replacement 2hp 220v pool pump and motor with 2 in discharge will the UST 1202 be what I need?
Reply
Hi Melissa, Could you email us a photo of your motor label and a wider shot showing the complete pump?
Reply
Motor to my Hayward Super Pump is getting ready to give out. Model K48M2N111 (SP1615Z1MEG) 2 HP Which would be the correct replacement motor? the UST1202? Need any more info?
Reply
Oops. want to replace motor in Hayward Super Pump.SP2615X20 Motor AO Smith model K48M2N111 Ser#29411FM 2 HP SF 1.0 FR 56J
Reply
I have a Red Jacket Centrifical irrigation pump powered by a 2 HP A. O Smith motor with a round connecting flange. Is there a replacement motor for this pump assembly. The rpm of the motor is 3450 Please advise and respond. Ted.
Reply
Hi Ted, I was able to locate some info on the Red Jacket pump, none of the motors we have are compatible with those pumps.
Reply
need a motor. just want to confirm the right one
heyward super pump SP2615X20 and motor is C48m2n111 2 HP 115/230. i think i want UST1202?
also do you have a video on how to install? i think i heard that you do
thanks.
Reply
The correct replacement motor for model #C48M2N111 is the UST1202. Here is a link on How To Replace the Motor on Your Pool Pump.
Reply
need a motor to replacement my hayward super ii pump model K48N2N104 SP 1620-Z1-BEE 230 V0LTS 2 hp and 1ph can you toll mee whichone is the correct to replacement thank you
Reply
Hi Alfredo, You will actually need ST1202 motor along with the Hayward Super II Tune Up Kit (GOKIT2).
Reply
i am replacing my hayward northstar pool pump motor. the current motor is a o smith sp1620-z-1-bns,2.0 hp. is your ao smith #ust1202 the correct replacement,and what seals,ect do i need to install the new motor. thanks tom
Reply
I have an A O Smith model C48AA35Ao1 pump motor that is tripping the overload protector. What is the best replacement for this? Would there be any advantage to going to more than the 1hp?
Reply
Hi, The UST1102 motor is the correct replacement for the A.O. Smith C48AA35A01 model. There is not advantage of going to a higher horsepower motor if it's not needed.
Reply
I have a A.O. Smith motor. Model #is k48N2N106c1 - is this the same thing? Will it work?
Reply
The A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor is the correct replacement for the model k48N2N106c1 motor.
Reply
I'm having to replace the motor on my hayward super pump model #SP2615X20, what is the correct replacement motor for this pump and are there any other parts that I'll need to complete the replacement of the motor on my pump? Thank you
Reply
Hello Carlos, A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor - UST1202 is what part brought up for your motor, please check your specs to confirm this meets your needs for horsepower, and service factor (SF). With any pump you want to replace the seals with a GOKIT which has your orings for pump lid, housing gasket,diffuser gasket, and pump seal. If you need a GOKIT for salt water click here.
Reply
Can I use this in place of a Sta-Rite Model P6RA6G-207L? All specs seem the same (except Max. amps a little lower), but I haven't seen what the shaft on the old pump looks like yet.
Reply
I have a 2 HP Hayward 4000 series northstar pump; the brass fitting in the impeller is stripped. Looking for a replacement impeller. The part number on the impeller is: SP4015C.
Reply
We unfortunately, don't sell just the impeller, sell it with the shaft seal. Which if you're replacing the impeller, it's a good idea to replace the shaft seal as well while you have it apart. The part number for that is 5112-026.
Reply
I have a 2HP Hayward super pump part 7-C56AA05A04-01 serial 201093M Frame Y56J Type CS SF 1.0 2850 RPM.
Need new ao Smith shaft end bell round (damaged because of leaking). Cannot find it. So then looking for replacement motor. However all replacement motors (SP2615x20) have 3450 RPM and indicate frame 56J, not Y56J.
Is there a replacement motor for this pump or do I need to buy complete pump with motor?
Reply
I have a 2hp Hayward super pump, Model #48M2N111, the motor is dead. Does your part #UST1202 a replacement for this motor. Also what else will I need to replace motor.
Reply
will this work for a replacement for A.O. Smith Model #C48M2N111A3 going on a Super Pump II Model # SP3015C20AZ
Reply
i have a hayward model k48m2n111, serial 19411fm, which is the correct replacement motor?
Reply
Hello Catalina, for the motor model k48m2n111 it matches the UST1202 motor. I would highly recommend replacing the pump seal, we would need the pump model to get that pump seal kit for you.
Reply
Hello tech Support.
Looking to replace our pool pump motor. Motor is connected to the Hayward pump model# SP3015X20AZ. Motor spec's are as follows: Century UST1202, model# K48M2N110C2, Volts: 115/208-230 HP:2 Ph: 1 Code:H RPM: 3450 FR: 56J AMPS: 19.6/10.4-9.8 Total HP = 2.20.
Do you carry this motor or equivalent? Also, please provide the proper seal kit? Thanks.
Reply
Good morning Mike, You are looking for A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor - UST1202 The seal kit you will need is Tune Up Kit Hayward Super II - GOKIT2 Unless you have a salt pool the you would need a gokit2salt.
Reply
I have a 2 HP HHPU series pump motor, Mod 1203006488 jandy motor. is your 2HP UST1202 the right replacement motor
Reply
Hi, Kevin. Yes, the UST1202 motor is the correct replacement based on the info provided.
Reply
what is the part # for the go kit (seals kit) for 2 hp ust1202
Reply
Hi, You will need to provide us with the model number or the make and model of the pump not the motor in order to locate a gokit if one is available for your pump.
Reply
What is the replacement motor for a Jandy pump, JHP2.0CP?
The current motor is Century Centurion, HP 2.0, 230v.
The system humms but not starting, capacitor is good, impeller is clear. The motor still turns freely from the back or front at the shaft. Do you think replacing the motor will solve the problem?
Reply
I have a Hayward super pump II, Model K48M2N116A3, the motor is dead. Does your part #UST1202 a replacement for this motor. Also what else will I need to replace motor.
Thank you
Reply
Hi, The STS1202R Motor is the direct replacement for model # K48M2N116A3 which is a dual speed motor. If you would like to switch from a dual speed motor to a single speed motor you can use the ST1202 motor. When replacing the motor you'll need the Hayward Super II Tune Up Kit - GOKIT2 which includes the pump shaft seal, o-rings and gaskets.
Reply
WE have a salt water pool and we are going to replace our Hayward 2 HP motor Model #C48M2N111A3 Serial #21610FM with this motor. Is there a specific kit for salt water pools to replace the seals/gaskits or is the GOKIT2 the correct one to use? another site states if you have a salt water pool you need different seals/gaskits? Please advise
Reply
Hi, Sherry. We will need the model number or name of the Hayward pump, then we will be able to find out if there is a saltwater kit for that pump. We're unable to locate the pump model number based on the motor model.
Reply
What pump do you offer to replace A.O. Smith part number: 7-165201-07 without any modifications to pump or motor
Reply
I need a replacement motor for my Hayward pool pump. I have a a.o.smith cat B130 part # 7-159988-06. Do you have what I need?
Reply
Hello Randy, we have the Motor 56j Thrd Full 2hp (b130), but I would recommend replacing your pump seal anytime you change out your motor. If you can provide us with the model of your pump we can help you find that.
Reply
I need a 2 HP pool motor pump to replace my failed A.O Smith P/N 7-165201-07
Please advise what motor you have with price.
Reply
Hi, Jim. The Century 2 HP Motor EE - Full Rate - B843 is the correct replacement motor for p/n 7-165201-07.
Reply
Hi, I have a Century ST1202 pool pump motor that I need to replace. Can I use the UST1202? I can't tell the difference between the ST and UST models other than it appears that the UST model has the option of using either 115 or 208-230 volts. The ST seems to be 208-230V only. I have a 208-230 circuit. Thanks, Don
Reply
Hello Don- No, it is recommended that you stay with the A.O. Smith Round Flange 2 HP Full Rate Motor - ST1202. The ST1202 is a full rated motor and has a total HP of 2.6. The A.O. Smith 2 H.P Round Flange Up Rate Replacement Motor - UST1202 is uprated and only has a total HP of 2.2. The St1202 is a stronger motor and if the appropriate parts aren't changed when going down to the UST1202, i.e. impeller and diffuser (if needed), then the motor will fail prematurely. How To Understand True Pump Horsepower - Up Rated vs Full Rated
Reply
Hello, my poolpump A. O. Smith with serial numer CL48L2DA23A2 is dead. Not working anymore. Is this one a good replacement or should I take the 1,5 HP. The whole machine is 12 years young at this moment or is it better to replace the whole machine. Can you please give me advise an tell me if I should choose this one or the 1,5 HP.
Do you do shipment all around the world.? what are your shipping costs. Reaction to my emails adress is also fine with me.
Thanks in advance.
Reply
Hi. Hedy. The info provided does not cross-reference to a specific replacement motor. If you can send us photos of the motor label and pump we can locate the correct motor for you.
Reply
Hi, my question is this: looking to replace our so Smith pool pump , Hayward 2.0 115v part# 719355401. Also says SP1520-2-1-ESC. Do you know which pump I should replace it with? Thank you
Reply
hi there..i really need your help....i get burn my motor pump..I just want to know exactly which one do i have to buy it..model # K48M2N110 super pump..model RS1500 1 1/2 HP..a.o smith..SECOND...CAN I UPGRADE TO 2 hp??? and 3er...what is the differences between round motor and c flange ?thanks in advance
Reply
Hello JJ, what matches K48M2N110 is A.O. Smith Round Flange 1 1/2 HP Full Rate Motor (C1101, ST1152) which I would recommend replacing the pump seal and orings found in the Tune Up Kit Hayward Super II - GOKIT2. Upgrading to the 2HP you would have to change the diffuser and impeller depending on whether you have a full or uprated model. Cface and round flange are the same motor type.
Reply
Hi. I have a Hayward Superpump, I want to replace the current motor. Current Motor is 2 HP single speed AO Smith model K48M2N111 (Hayward part SP-1615-Z-1-MEG. Current pump also says SF = 1.0
Question 1 = Is this replacement motor equivalent with a SF of 2.0? Is it still plug and play for lack of a better term?
Question 2 = Is there any EE or 2 speed or variable speed motor replacement options for me?
Reply
Hi. The UST1202 is the correct replacement motor based on the info provided. The replacement motors are considered plug and play. Here are a list of EE motors the B795 (single speed), B2977T (dual speed w/ controller) or the ECM27CU (vs speed). Whichever option you purchase I would recommend also getting the Hayward Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
K48M2N110 is A.O.Smith Round Flange 1 1/2 HP Full Rate Motor (C1101,ST1152)Upgrading to the 2HP you would have to change the diffuser and impeller depending on whether you have a full or uprated model here again... ..ok...here is the info ..i have SF 1.33 A.O SMITH. KW 1.1 TYPE UAK CODE L,AMPS 19.4/9.7 1 1/2 HP RPM 3450..NOW i need to know if is full rate or up rate like your question before.and let me know what motor i have to buy..also if i can upgrade to 2 hp.thanks
Reply
Hi, JJ. A 1.5HP full rate motor has a total hp of 2.25 so technically you already using a 2hp motor. You will have to upgrade to a 2hp full rate motor ST1202 which will have a total hp of 2.6. You will have to replace the impeller along with the necessary parts to make the conversion depending on the pump model. If you're replacing a 1.5hp full rate motor to a 2hp up rate motor - UST1202, you do not have to replace the impeller, diffuser etc. just the pump seals.
Reply
I have a Hayward (model # sp2607x10 on pump housing) I can't read info on motor but if I remember correctly it's 2.5HP. Can I replace 2.5 HP with UST1202 2HP without changing the 220v wiring and using the old impeller and diffuser? I do plan to get the seal kit
Reply
Hi, Matt. The original pump model # SP2607X10 is for a 1HP pump. If the motor was increased to a 2.5HP (max) and now you would like to decrease the motor to a 2HP (max), the impeller and diffuser will need to be changed. The kit you will need is the Hayward Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
What exactly does full rate and uprate mean when compared to the regular motor if they are all the same HP? I need to order a replacement motor for my Jandy HHPlus series pump and it has a 1 1/2 hp PHPU motor. And why does the replacement I saw not have a run capacitor or are the pictures online just general motor pictures. Thank you
Reply
Hi, John. Our How To Understand True Pump Horsepower guide explains the difference between full rate and up rate motors. The Jandy PHPU 1.5hp original came with a 1.5hp up rate motor (UST1152 or B229SE). The UST1202 motor does come with the capacitor on top.
Reply
What exactly does full rate and uprate mean when compared to the regular motor if they are all the same HP? I need to order a replacement motor for my Jandy HHPlus series pump and it has a 1 1/2 hp PHPU motor. And why does the replacement I saw not have a run capacitor or are the pictures online just general motor pictures. Thank you
Reply
Hi, John. Our How To Understand True Pump Horsepower guide explains the difference between full rate and up rate motors. The Jandy PHPU 1.5hp original came with a 1.5hp up rate motor (UST1152 or B229SE). The UST1202 motor does come with the capacitor on top.
Reply
I have the B843....what is the correct run capacitor for this model
Reply
Hi, Dave, The Century B843 motor uses the 50MFD 370VAC Run Capacitor - RD-50-370.
Reply
Jacuzzi Magnum Force 2hp. pump shows as I have, yet the picture for the replacement motor (56J-UST1202) shows the capacitor on top of the motor vs on the back end as mine is so the threaded locking ring can slide over the motor. Will I get the right motor?
Reply
I forgot to mention in my previous email the AO smith pump motor part number is 7-184950-22. What is the drop in replacement for it and will the capacitor be on the back side of the motor?
Reply
Hi:
I have a Jacuzzi 2HP magnum with this exact motor. It started making a loud grinding noise and isn't getting any water through it. It's about 15 years old. I think my options are buy a new motor, buy a new pump (identical), or get a different pump. What's an equivalent pump (or motor) that would get similar results/performance, but be more energy efficient? I don't have anything built into my control panel that supports multiple speeds - just on and off - not sure this limits me.
Reply
Hi, Jay. The Magnum Force Pump 2 HP Pump - 94027120 is the exact replacement. You can use the Super II Pump EE - SP3015EEAZ as an energy efficient replacement option.
Reply
Several years ago, the motor on my old Hayward Super II pump. I bought a HAYWARD SUPER II PUMP 1 HP model SP3007X10AZ, not realizing at the time that the 1 HP motor was too underpowered for my 25,000 gallon pool with roughly 196 feet of head. Now that motor has burned up, and, I want to replace it with a more powerful motor, mounted on my existing pump housing. Is this the motor I need, and, will I need a kit in order to adapt it to this housing. If not, which motor/kit do I need?
Thanks.
Reply
Hi, Scott.I would recommend recalculating your feet of head using the steps in our How To Size a Pool Pump guide. I would recommend replacing the pump because rebuilding the pump to a 2hp would not be far off.
Reply
I'm looking to replace the run capacitor for this exact motor (UST-1202 - the top capacitor). Do you know which capacitor I should use for a replacement?
Reply
Hi, I have a Hayward Northstar SP1615Z1MNSC and it started making noises so I am thinking of replacing it, what would be the replacement motor or pump? Thanks.
Reply
I have a ST1202 2 hp motor on an irrigation pump. If something goes wrong the pump house will flood. Is there a submersible motor that will replace my current one?
Reply
Hi, Marty. There is not a submersible pump that is available to replace the ST1202 motor.
Reply
I have a Hayward Superpump. The motor has seized up (about 7 years old). Original motor is A.O. Smith C48L2N134B1 1.5 hp 115/230 volts
Need a replacement motor. Looking at the 56J-UST1202. Will that work?
Also, what other parts will I need to buy as far as gaskets, etc.
Reply
Your replacement motor is actually the model UST1152 and we recommend using the GOKIT3 or GOKIT3SALT if you have a salt water pool for replacing all the main seals and gaskets.
Reply
I am replacing the same motor for a salt water system pump. Is there anything I need to order to go along with this motor because I have a salt water system? Gaskets, seals, etc.
Reply
Hello, we would need the pump model number to see which seal kit you would need.
Reply
will this work as a replacement for my Hayward Model #: C48M2N111A3?
Reply
Hello, Based on your motor model number, the UST1202 would be the correct replacement. I would also recommend replacing the shaft seal.
Reply
I need to replace a motor---AO Smith K48N2N104. Is this a suitable replacement? Is so, how long to ship to Arizona?
Reply
Is this electric motor a fit to a 2 Hp hayward pool pump?
My pool pump drive motor is emitting a high pitch noise as though the the bearings are frozen.
Reply
Hi, Andres. This UST1202 motor can fit several Hayward pumps. However, to confirm if this is the correct motor, we will need the motor PART, CAT or MOD number.
Reply
I need to confirm that the UST1202 is the correct replacement motor for my current AO Smith model K48M2N111
Reply
Hi, Scott. This Century UST1202 motor is the correct replacement for model # K48M2N111 motor.
Reply
I am looking for the right pool motor.
I currently have the HST225 (K48AA31A01) (Volts 115/208/230 KW) (HP-225) (PH 1) (Code E) (RPM 3450) (56J) (SF 1)
Reply
Hi, Luis. This Century UST1202 motor can be used as a replacement for the HST225 motor.
Reply
I have a Hayward SP4015X20NS motor that has locked up. What is the correct replacement motor and go kit #?
Reply
Hello Kevin, depending on what year your unit is there is the 2008-current version which would be A.O. Smith 2 HP Up Rated Northstar Replacement Motor - USN1202 and there is no gokit with this there is HAYWARD NORTHSTAR/TRISTAR SHAFT SEAL (OEM) - SPX3200SA. With the Hayward Northstar 1998 to 2007 needs a Tune Up Kit Hayward Northstar 4000 Series Pumps (Pre-2003) - GOKIT66 and the USN1202 motor is the same.
Reply
I have a UST 1202 Model number K48M2N110C2 2 hp 56J frame. Looks to me to be a 6 bolt square flange. What do I use as a replacement? It locked up. All the ones I see have a 4 bolt round or square flange.
Thanks
Reply
HI, John. This UST1202 motor is the replacement for MOD # K48M2N110C2.
Reply
Good Morning,
Will this substitute for a Hayward K48M2N11083? Also which gasket kit goes with this?
Thank you
Shawn
Reply
Hi, Shawn. This Century USt1202 motor can be used as a replacement for MOD # K48M2N110B3. The motor model # will not indicate what seal kit is needed for the pump, we will need the Hayward pump housing model number or name.
Reply
My Jandy PHPU2.0 motor is wearing out. I am unable to find this motor for sale and believe it has been discontinued. What would be the best replacement motor so I do not need to change other sections of my filtering system?
Reply
Hi, Steve. This UST1202 Motor can be used to operate the PHPU2.0. I would recommend replacing the pump seal and the o-rings which are located on the Jandy Plus HP Original (2005 and Prior) PHP and PHPU Parts Diagram page.
Reply
Pump motor stopped. Looking for a replacement motor. Model is SQ1152, 1.5 hp, type:Regal Beloit epc. Faded, can't read the manufacturer sticker(Century??)...Would like to increase flow. Can I put a 2 hp motor on without causing a problem? There is a spa attached to the pool that uses the same filter(Pentair).
This will be my fourth motor in 17 seasons and I live in PA so our pool is only open 3 months a year. Does anyone make a motor that will last?
Thanks.
Rich
Reply
Hello will this replace motor for model # K48N2N104 A.O. smith.... I didn't see that model # listed but everything else looks correct?
Thank you
Reply
Hi, I have a 17-yr old Hayward Super II Pump SP3015X20AZ w/ 75' head in Arizona where I run the pump 12 hours per day every day. The original unit lasted 11 years until the motor went out. I then replaced it with a refurbished motor and I am on my 4th refurbished motor in 6 years. Lately the water is barely flowing over my raised hot tub - it used to really flow. I've replaced seals every time w/ motor - white impeller ring inside is shot. Is it time for an all-new pump? Thoughts?
Reply
Hi Frank, Yes based on what you have said I would suggest an entire new pump after 17 years some of the internal components of the pump may be worn down. If you want to replace with the exact same pump then you can get this Hayward Super II SP3015X20AZ or I'm a big fan of the PureLine Prime Variable Speed Pump this pump is great as it lets you dial your HP into any HP between .5 HP and 1.65 HP which will save you a ton on your electrical bill, typically 65% savings over a single speed pump.
Reply
i have 2 1/2 hayward super pump ll the motor is burn , know i want 2hp with evething that i need to do do the change please send me all the informatio thank you very much
Reply
Hi, William Londono. To change your Super Pump from 2-1/2 HP to 2 HP you will need the following parts. The Motor - UST1202, and the 2 H.P. Drive Train Upgrade - SPX2615CKIT.
Reply
I have a sp1615z1m 2hp superpump I am replacing. Mine has no dome on the Top. Dose it make a difference if the replacement has one? All the information on the labels match
Reply
Hi, John. This UST1202 motor is the correct replacement. It does not matter that the replacement motor has the Capacitor housing on top. I'll also recommend that you get the Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
We have an AO Smith motor. Its a B2843 serial # 3344096M Type CX
Part 7-196257-67
HP 2.0
What do you recommend to replace it?
Reply
Hi I have an ST1202, model k48n2n106c1 will this work? I also need a seal kit for hayward super II pool pump. Thanks
Reply
I have a Hayward Max-Flo Pump Motor (K48M2N111) that I need to replace. Can you please confirm that the UST1202 is the correct replacement motor?
Also, I would like to replace the Pool Motor Seal. I have the Hayward SP2815X20 Pool Pump for my Salt Pool. Which Pool Motor Seal do I need?
Also, are there any other parts that you would recommend that I replace, since I have the motor separated from the pump?
Reply
Hi. This UST1202 motor is the correct replacement for the Hayward Max-Flo SP2815X20. I will also recommend that you get the Max-Flo Tune Up Kit - GOKIT1SALT.
Reply
I am in need of changing out my pump motor and i was wondering since the motor that i have is discontinued (sts1202rv1 2 1/3 HP ) what is the replacement pump for it
Reply
Hi, I have a Jandy stealth with an AO smith 2 HP motor. Will this motor work for my application?
Reply
You would need to use the specific motor model, part or catalog number to cross-reference the specific motor that you need.
Reply
will the A.O. Smith 2 H.P Pool Motor Round Flange 56J - UST1202
interchange with a A.O. Smith 2 hp model C48M2N111A3 FR 56J ?
Reply
Hi, Terry. Yes, this UST1202 motor will replace MOD # C48M2N111A3.
Reply
Looking to replace my Haywood super pump 2.0 hp (sp2615x20) Is this A.O Smith comparable ?
Reply
Yes, this is the correct motor for your pump and we would advise using the GOKIT3 for a chlorine pool or the GOKIT3SALT for a saltwater swimming pool.
Reply
Is this the correct replacement for my existing AO Smith K48M2N111
Reply
Hello Mike- The A.O. Smith 2 H.P Pool Motor Round Flange 56J - UST1202 would be the correct replacement motor.
Reply
current A.O. Smith motor model is K48N2N104. Is this motor an acceptable replacement?
Reply
Hi TJ, You would actually need the ST1202 2 HP Full Rate Replacement Motor which is a direct replacement for your K48N2N104 motor.
Reply
I have this pump in 1hp I want to upgrade to 2hp will the 2hp it the flange of the1hp??
Reply
Hi, Iggy. The flange of the 2hp will match the 1 hp. However, you will have to make sure that your filter, plumbing and overall system can handle the water flow of a 2hp pump if you're planning to upgrade the impeller and diffuser of the pump also.
Reply
I have a Hayward RS1500 1.5HP. The motor needs replaced, will this motor work as an upgrade?
Reply
Hello,
I am looking to replace a Hayward Super Pump with the label showing A.O Smith K48M2N111 as the model. Is this the correct replacement part for it? We have also switched to salt water. I see the GoKIT3SALT tune up kit. Is that the right tune up kit that goes with this motor? Thank you.
Reply
Yes, this would be the correct motor and the GOKIT3SALT would be the correct seal kit as well.
Reply
i need to replace my pool pump MOD K48M2N110C2 and the seal that goes with the Hayward.
Reply
The seals and gaskets are based on the model name or number of the front pump housing that the motor bolts to. If you cannot locate that then you can send us images of it to us at upload@inyopools.com so we can assist you.
Reply
will this motor make up to my pump that is super seris
Reply
Hi, Gary. This motor will fit the Hayward Super Pump or Hayward Super II Pump Series Pump.
Reply
Yes I am trying to replace a waterpump MOD number c48k2n143c1c 1 hp to your 2 hp will it work?
I have roughly 15,000 gallon inground pool with a sand filter
Thank you
Reply
Does the A.O. Smith 2 hp pool motor come with a gasket set
Reply
Hi, Alan. A gasket set is not included with these motors. They're sold separately based on the make and model of the pump strainer model.
Reply
I have a Hayward Super Pump Century 1.5 HP Motor (C48L2N134) and would like to know if I can replace with the 2 HP version (UST1202) as an upgrade from the 1.5 HP. My pool is large, about 22K galloons, and what would be the benefits of doing this upgrade.
Reply
Is this motor compatible with my Hayward SP2815X202 2HP Max-Flo Dual speed pump with SP-1615-Z-2-M, Motor, MOD:K48M2N116, FR 56J,
Volts 230, HP 2 to 1/3, RPM: 3450 / 1725, Max load amps: 9.1 / 3.4, Phase 1, Code G ?
Reply
My old pump was wired for 230 volts. Does the replacement pump come ready to rewire for 230?
Reply
Yes, this model does come preset from the manufacturer at 230 volts. Not all do though. Best to confirm your exact motor model, part or catalog number and then confirm the specifications of it.
Reply
what is the difference between a UST1202 and a ST1202?
Reply
Hi, Dave. The service factor which determines the motor's Total HP. Check out our How To Understand True Pump Horsepower - Up Rated vs Full Rated.
Reply
Hello, would this would be the correct replacement motor for for my C48M2N111a3 motor? Thanks very much for your help.
Reply
Yes, this would be the correct replacement motor for your model motor.
Reply
How do I remove the housing attachment from the old pump?
Reply
Good day, we have a lot of DIY and HTG's you can review that would help you change the motor. If you need more help you can CHAT with us or give us a call at 407-834-2200.
Reply
Hi,
Do you have a replacement motor for model T55CXCJM (1347) (1081)?
Reply
Hello, Can you please take a side view picture of the entire pump along with the motor label? Nothing had come up with those part numbers provided.
Reply
What is the Warrantee on the replacement motors
Reply
I have a Hayward Super II pump, SP3010X152AZ and I need to replace motor, SP1610Z2MC, part #7-181093-03, type CXPM what motor would I replace it with and what tune up kit would I need? Thanks
Reply
The replacement motor for this model is the part number 5387X. For a chlorine swimming pool the seal kit is the GOKIT2 and for a saltwater swimming pool the seal kit is the GOKIT2SALT.
Reply
My old AO smith motor needs replacement in a Hayward Super 2 pump. current model is k48m2n110 a 1.5 hp unit , sf@1.33, model sp3015eeaz
thanks for any help,
Dennis in California.
Reply
Hi, Dennis. Single speed pump and or motors are prohibited from being shipped to the state of California. Your options are the Dual Speed Motor - STS1152R or the Variable Speed motor - ECM27CU. You will also need the Super II Pump Tune Up Kit - GOKIT2 or GOKIT2SALT.
Reply
I need to replace pump motor SP-1615-Z1-MBK. Differences on UST 1202 are amps 21.6/10.8 & type UAC. Is this the right motor? And does the gokit2 have a #?
Reply
I need to replace pump motor SP-1615-Z1-MBK. Differences on UST 1202 are amps 21.6/10.8 & type UAC. Is this the right motor? And does the gokit2 have a #?
Reply
Hello, We will need to know the model number of the entire pump. Can you please send a side view picture of the entire pump ?
Reply
Per your advice, this motor will replace my A.O. Smith spx1615z1m. However, my existing motor does not have that little hood on top. Does that make a difference and what is under the hood?
Reply
That is a capacitor, some motors have them inside. AS long as frame and voltage match up you are fine.
Reply
It makes no difference unless you have plumbing directly in the way which you should not. The cover has a run or start capacitor inside.
Reply
I am replacing a Hayward max flo sp1615-z-1-mxbk. Will this work as a replacement?
Reply
Would this be a replacement for my salt water pool ?
According to the horsepower and service factor rating on the back of your pump housing, the UST1202 would be the correct replacement motor. If you do replace the motor, we recommend upgrading to a saltwater shaft seal to prevent any leakage.
Reply
what is the part no for the seal?
Reply
Alexis, The seals are all included in the MaxFlo Tune Up Kit - GOKIT1 or GOKIT1SALT.
Reply
Can I replace a Hayward SP-2615×20 with this? Aside from the seal, are there any additional parts I would need?
Reply
Hi, Matt. Yes, this UST1202 motor along with the Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT are the only parts you'll need if the pump components are in good condition.
Reply
Can you tell me what is the difference is between the UST1202 and the USN1202?
Reply
The USN1202 is specifically designed for the Northstar series and actually has a slightly stronger horsepower by about a quarter.
Reply
Thanks, So it sounds like the physical specs would allow fitment of either the UST and/or UST, correct? Capacitor and slight hp difference? Al's, we do use this on our Ag exempt farm for a line of organic planters as a prefilter. We grow in both AZ and CA, need the USN1202 motor and a 3-hp (also Northstar), can these be sold to the farm business and shipped within CA for our N.Calif grow shed?
Reply
I need to replace the pool pump motor and saltwater seal kit. It's a Hayward Super Pump NSE-50 with a Century 2 HP motor, Model K48M2N111, SP1615Z1MEG. Is this the correct replacement motor and what is the part number for the saltwater seal kit?
Reply
Yes, the UST1202 is the correct replacement motor for your K48M2N111. The Hayward Super Pump uses the GOKIT3 or the GOKIT3SALT.
Reply
What capacitor is used on the following motor:
UST1202
Reply
The UST1202 uses the start capacitor 124-149 MFD (BC-124) and the run capacitor is the 25MFD 370V.
Reply
Will this motor bolt up to a Hayward SP2610X152S pump. I can not the dimensions on the bolt up holes, AKA points on center.. Thank You.
Reply
Hi, Ralph. Yes, the UST1202 can be used as a single replacement. The Hayward Super Pump uses the GOKIT3 or the GOKIT3SALT.
Reply
Is this the correct replacement motor for Hayward SP3015X20AZ & Model# K48M2N110C2 . its is 2HP, UST 1202
What kit is also needed
Reply
Hi, Jake. Yes, the A.O. Smith 2 HP Round Flange 56J Up Rate Motor - UST1202 will be the correct replacement for the motor you currently have with model #K48M2N110C2. The correct seal kit you will need is the Tune Up Kit Hayward Super II - GOKIT2 for a Chlorine pool and the Saltwater Tune Up Kit Hayward Super II - GOKIT2SALT for a Saltwater pool.
Reply
I am replacing a Hayward Super Pump II Model: SP-1620-Z1-BEE.
Is the Hayward SP3015X20AZ the correct replacement?
Thank you.
Reply
Based on the motor model that you have provided we, unfortunately, do not carry the Hayward Super 2 that would be your replacement. That model would be the SP3020X25AZ.
Reply
This is the correct replacement, make sure to order the pump seal kit also. NOT California title 20 compliant. Have you ever thought of changing to a Variable speed pump?
Reply
Yes, that is the correct replacement.
Reply
replacement motor 35-126-1423 Motor, Century,2.0hp,208v-230v,1-Spd,56Jfr,C-Face Thd
Reply
Can this replace a Hayward super II Model C48M2N111A3, 2 hp, 115/230 volts, 56J? Can you ship it to California?
Reply
Hello, Motor number UST1202 will be the correct motor. However, it is not Title 20 compliant for California. You will need this motor. http://www.inyopools.com/Products/07501352042259.htm
Reply
I am looking for a replacement motor of this type is the 1202 type motor ok ?
Unfortunately, we do not carry replacement motors in this genre. You may want to get with an irrigation company as they may have these types of replacement motors.
Reply
what is the difference between the K48M2N110 I have and this motor K48M2N110C2, what does the C2 at the end represent? will this work as direct replacement?
Reply
Will this replace the attached? I am also in need of an impeller. Do you have that part number also?
thank you
Hello, I can look into this for you. Can you please send a side view picture of the entire pump?
Reply
Yes and order impeller Spx2615 and the pump seal kit GOKIT3 unless you have a salt pool
Reply
We really are not able to determine if this is the correct motor as we are unable to enlarge & read the motor label info. As far as the impeller that is determined by what wet end/or pump is attached to the motor, again we do not have that information. Can you give us a model # off of your pump?
Reply
Is this the correct replacement for the attached?
Also looking for replacement impeller - (also attached) want to make sure I am getting the correct ite,
thank you
Hi, Kimberly. This UST1202 is the correct replacement. The replacement Impeller - SPX2615C along with the Super Pump Tune Up Kit - GOKIT3 or GOKIT3SALT.
Reply
Have a Hayward Superpump II SP3020EEAZ (ID 21110512051773017) installed new in 2007 - see attached motor data plate. Is this UST 1202 the correct motor replacement? Thanks, Tom
Hi, Thomas. The ST1202 motor is the correct replacement motor. You will also need the Hayward Super II Pump Tune Up Kit GOKIT2 or GOKIT2SALT.
Reply
We have this motor and its 2Hp but we want to go down to a 1.5 or 1hp due to our pool is only 16/32 and we were told this 2hp is overkill for this size. Which do you suggest?
the specs plate on the motor I have matches this motor exactly, however the motor I have has six bolts to attach to basket this one has four. can I get a different flange to attach to basket?
Reply
Hi, Richard. The motor mounting flange is different from the pump motor mounting plate.
Reply
Hello,
I have a Aquatron pump by Purex that needs a new motor. The model number of the current motor is K63CXDGK-5171. Is the UST1202 the correct replacement? Also, which seal kit do I need?
Thank you
Reply
My motor is model # C48M2N111B1- what is the correct replacement motor for me? Thanks much!
Reply
Hi Ed, Could you give us the information off of the motor for your current pump like HP, Amps, Volts, SF, Frame, Model #, etc.. Also could you give us the pump make and model information, common pump names would be Pentair Whisperflo, Pentair Challenger, Jandy Stealth, etc.. To supply this information click the reply link below, also if you could send a few photos those are always helpful as well. If you send photos then take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get any of this information we can make the proper recommendation.
Reply
It's an old, worn pump- the label is difficult to read.
Hi Ed, Yes this UST1202 is the correct replacement motor for the motor included in your photo. You will also need a Hayward Super Pump Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
looking for a pool pump motor model k48aa32a01 frame 48y
Reply
Hi John, The UST1202 is not the proper replacement motor. You will actually need the ST1202 2 HP Replacement Motor
Sent question in earlier but had the wrong gallon amount. Pool is 25,000 gallons not 250,000. would it still need a 2 hp pump?
Reply
HI Blake, In most cases a 1 HP or 1-1/2 HP pump would be sufficient for a 25,000 gallon pool.
Reply
is this the correct replacement part for what i have, and what oring and gaskets kit would i need with it.
Hi, Brian. This UST1202 motor along with the Hayward Super II Pump Tune Up Kit GOKIT2 or GOKIT2SALT are the parts you will need for your model pump.
Reply
I had my motor replaced last fall . it was a 1 1/2 hp hayword the repair guy put a 1hp on it . a UST1102 model # c48k2n143c1c .
I m trying to find a replacement motor in 2 hp without replacing entire unit (( just motor shaft )) what one will hook up to my unit ?
' thank you
TIM
Reply
Will this replace A.O.Smith model no. 7~184874~01
Reply
Hi Robert, We are showing that your motor is a dual-speed motor and the direct replacement is this Hayward 2.5 HP Dual Speed Up Rate Motor - SPX1620Z2M were you wanting to switch to a single-speed motor or were wanting to stay with a dual speed motor?
Reply
What is the replacement for the following?
Hi Jennifer, You will require this BN37 Pool and Spa Motor to replace your motor in the photo.
Reply
I have this motor what pump goes with it.,my pump leaks motor is new
Reply
Hi Russell, could you send us a few photos of your pump so we can suggest the proper parts? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
What is best most efficient motor to replace this motor? is the exact model a replacement as well?
Hi William, The UST1202 motor on this page is an exact match replacement to the motor in your photo. The most energy-efficient motor will be this 2.7 HP Variable Speed Replacement Motor. Here is an article we wrote on the Energy Savings of a Single Speed Pool Pump Vs. a Variable Speed Pool Pump. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
I am looking at your motor #K48M2N110C2 and wanted to know if would be a good replacement for my motor model
#K48N2N106C1 (2 HP).
I would like to make sure this is the replacement motor I need. Thank you
Yes this is the correct replacement motor for the motor in your photo. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply your photos simply click the reply link below and upload your photos. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
Hi can you please tell me if your motor match mine and what seal kit do I need thank you, I hope Picts help you
Hi Ricardo, This is NOT the correct replacement motor for the motor included in your photo. You will require this Hayward 2 HP Up Rate Dual Speed NorthStar Replacement Motor - SPX1615Z2MNS You will also require this Hayward Northstar Seal Kit if your pump is from before 2003 then you will need this Hayward Northstar Before 2003 Shaft Seal if your pump is from after 2003 then you will need this Hayward Northstar After 2003 Shaft Seal
Reply
Here is a picture of my pump and motor. I want to order this pump but I need you to suggest the right seal kit. See picture below for my configuration.
The seal kit for a chlorine swimming pool is the GOKIT3 that you can view here, and for a saltwater pool, it is the GOKIT3SALT that you can view here.
Reply
have a pentair 177451 motor 2hp can i replace motor with century 2hp 56j ust1202 pump and propellers with fit or housing be compatible?
Reply
No you cannot use the UST1202 on the 177451 motor, you would require this B2842 Replacement Motor. When replacing your motor you will need a seal kit. For us to suggest the proper seal kit could you send a photo of a wide shot of your complete pool pump to show the pipes going in and out of the pump? To supply this photo simply click the reply link below and upload your photo. Once we get this photo we can make the proper recommendation for the seal kit.
Reply
What is the difference between a ST1202 and UST1202.
Thanks
Reply
Hello, the UST1102 is an uprated model and the ST1102 is a full rated model. Here is a guide that we put together called "How To Understand True Pump Horsepower - Up Rated vs Full Rated" that explains the difference between those.
Reply
will this work for a K48N2N106C1 motor mod?
Reply
Hello, the correct single speed replacement motor for your motor model K48N2N106C1 is the ST1202. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
I have a Hayward SuperPump Dual-Speed 2HP that is dying. I do NOT want a replacement with dual speed, we never use it - the pump is on a timer and stays in high speed always. The UST 1202 looks to fill the bill for me. I realize that the current motor bolts to the pump portion inside that plastic housing. (I have had this entire deal disassembled for impeller and seal replacement in the past.) And that the replacement motor will bolt to the housing on the outside - that's not an issue for me.
The UST1202 or Century 2.0 HP Round Flange 56J Up Rate Motor - B230SE can be used to replace the current 2.0THP Dual Speed. The Tune Up Kit Hayward Super Pump - GOKIT3 or GOKIT3SALT for salt pools is needed when replacing the motor. California Title 20 Compliant Options: Dual Speed - B2977 or Variable Speed - ECM27CU (check voltage requirements) California’s New Variable Speed Pool Pump Law
Reply
Can I use this pump to replace my pump, Model # Century HSQ220, Serial # 33213CHCL030583976. It has a round flange.
Reply
Hi Chris, could you send us a few photos of your pump and motor? Please take a close up shot of the motor label as well as a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation.
Reply
Need a motor. Not sure which one
Hi James, this is the correct single speed replacement motor for your motor model UST1202. It is recommended to replace the seals as well when replacing a motor. In order to locate those, we will just need the front pump housing wet end model name or number that the motor is attached to. You can also attach a few images of that in a reply here if you need as well.
Reply
Good morning
A question was sent to you on Friday and I am adding additional questions:
What is the correct Century replacement motor for the motor pictured?
Also need to know the part # for replacement bearings for motor pictured.
And.... a seal # as well.
Thank you
Jamie
Hi James, for the motor model UST1202 the rear bearing part number is 5270-31 and the shaft end bearing is part number 5270-32. For a chlorine swimming pool, the main shaft seal is part number 5110-11 and for a saltwater pool, it is 5250-235.
Reply
I have a jandy jhpu 2.0 motor will this work as a replacement
Hi Abel, You will actually need the B230SE 2 HP Up Rated Motor as well as this Jandy JHPU2.0 Replacement Shaft Seal. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I noticed that the motor you said that i need doesn't have a run capacitor on top and my old one does. Does that matter? Will i have to wire it differently?
Reply
This will not be an issue, the new motor has an internal capacitor where the old motor had an external capacitor and they will be wired the same way.
Reply
hi
i have hayward k48m2n111 can i use
Reply
Hi Sam, yes this is the correct single speed replacement motor for your motor model k48m2n111. It is also recommended to replace the seals when replacing a motor. We would just need to know the model name or number of the front pump wet end housing that the motor attaches to in order to locate those for you. You can also reply to this with a few images of the housing uploaded if you need assistance with that.
Reply
This motor shows compatibly to my motor per the motor tag. However, the flange appears to be different. My motor flange has 6 bolts. This motor has 4 bolts. Will the 4 holes line up correctly and not use the other 2 bolts or is there another motor with the correct flange?
Hi Richard, yes the motor is mounted by 4 bolts and it is bolted to a plate that uses 6 bolts to attach to the rest of the pump housing. This is the correct single speed replacement motor for your motor UST1202. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
can you install shaft seal and impeller and ship
Reply
Hi Robert, unfortunately, we do not assembly these motor and pump parts however here is a general guide that we put together called "How To Replace the Motor on Your Pool Pump" that may assist you.
Reply
We have a UST1202 that is four years old and on its last leg. The picture is of the label on the pump motor we have currently. Would this new motor be an upgrade or about the same? What motor could be purchase that would be an upgrade from what we have? If we do the switch ourselves, what other parts would we need?
Hello Gretchen,Based on the photo provided. The Century Motors Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 would be the exact replacement for you. For seal kits you can use our How to Guide Finding the Tune-Up Kit for Your Pool Pump.
Reply
We have a Hayward SP1610Z1M 1.5hp. Can we use this 2.0 as a replacement? The photo is from our existing pump. Thank you.
Yes, this UST1202 2 HP is the correct replacement motor for the motor included in your photo. You will also need a Hayward Super Pump Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I have a model C48L2N134B1 what replacement motor do I need. If I get a U
Reply
I have a model C48L2N134B1 what replacement motor do I need. If I get a UST 1202 can that match up whit the strainer
Reply
Hi Robert, yes this is the correct replacement motor for your motor model C48L2N134B1. When replacing a pool motor we do suggest a Seal Kit. Could you send us a few photos of your pump so we can suggest the proper seal kit? If so then please take a wide shot of the complete pump to include the pipes going in and out of the pump. To supply photos simply click the reply link below and upload your photos or quickest provide them using our live online chat feature. Once we get those photos we can make the proper recommendation for your seal kit.
Reply
Is this the correct replacement for Hayward super pump model# k48m2n110?
Hi Jimmy, Yes, this is the correct single-speed replacement motor for the motor included in your photo. You will also need a Hayward Super Pump seal kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
I have the hayward 2.0 super pump model k48m2n111 I see that this is the correct motor. I want to also replace the seals my body part number is sp2615x20 what do i use.
Reply
The necessary gasket kit for the Hayward Super Pump is the GOKIT3 or the GOKIT3SALT
Reply
adquirí este modelo de bomba, pero me di cuenta que la conectaron a 110, según yo esta bomba se puede conectar a 220, se puede?, en casa tengo energía 220, gracias de antemano
Reply
Este motor es de doble voltaje. Viene de fábrica configurado en 230v y tendría que cambiarse manualmente a 115v.
Reply
Is this the motor I need?
Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Hayward Super Pump Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
mine is USQ1202 your is UST102
mine is FR 48Y your is FR 565
K48M2PA105C5 Centry
is this OK
Reply
No this will not be the correct replacement. Please click this for the proper replacement motor for your - USQ1202 48Y Frame 2 HP Motor.
Reply
I have model C48M2N111B3. Is this the correct replacement motor for me?
Yes, this is the correct replacement motor for the motor included in your photo. You will also need a Hayward Super Pump Seal Kit when you replace your motor. We put together this Video on How to Replace a Pool Pump Motor which you may find helpful when you tackle this project.
Reply
My current model is K48M2N110B3 as shown in the photos below. Will this be the correct motor replacement model for this? Thanks for your help.
Hello Paul. The Century Motors 2.0HP 56J Up Rated Motor model UST1202 is the correct replacement for your current motor model K48M2N11083. It is recommended that the motor shaft seal, seal plate gasket/0-ring, and diffuser O-ring be replaced at the same time. Please review the attached link to the motor model UST1202 and identify the appropriate Tune-Up Kit for your pump (under the heading: Don't Forget Your Tune-Up Kit. Tune-Up kits are specific to the pool pump manufacturer/model and not the motor model. Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202
Reply
I need to replace my pump motor,I have a hayward super ii and the motor is a A.O smith part # 7-177062-05,I want know what comparable motor u have that I can buy to replace my motor on the pump. Please e-mail back soon as posible,would really appreciated. Antonio
Reply
I show the replacement pool pump motor for your 7-177062-05 is the...Century 1.5 HP Round Flange 56J Dual Speed Full Rate Motor - B2977
Reply
I need to replace my pump motor. Part number 7-164304-24. What is comparable?
Here is the link to the proper motor replacement for your 7-164304-24Century 1.5 HP Round Flange 56J Full Rate EE Motor - B129
Reply
I would like to find a compatible replacement for my pump.
Thank you for contacting Inyo Pools, The correct motor replacement is Century 2.0 HP Round Flange 56J Full Rate Motor - ST1202
Reply
Hello, was wondering if this pump is a good replacement for my old one that just stopped working. Also does it come with the plug attached
Thank you ??
Hello Angela. The Century Motors 2.0 HP Up Rate Motor model UST1202 is the direct replacement for your current US Motors model EUST1202. The replacement motor does not come with wiring attached. Typically, the existing wiring is utilized with the new motor. It is recommended that the motor shaft seal, seal plate gasket, and diffuser o-ring be replaced t the same time as the motor. The GOKIT3 contains the parts necessary to complete this repair. Hayward Super Pump SP1600 & SP2600 Series
Reply
Thank you so much for your help and quick response.??
Reply
Is this a proper replacement for a A.O. Smith model K48A34A06
Reply
Hello Walter. The Century Motors 2.0 HP Up Rate Motor model UST1202 is a compatible replacement for the A.O. Smith motor model K48A34A06.
Reply
Hi..replacing motor model K48M2N111. is this correct replacement
Reply
Hello Edwin. The Century Motors 2.0 HP Up Rate Motor model UST1202 is the compatible replacement for the motor model K48M2N111.
Reply
I need to replace the bearings this pump. Do you sell bearings for this pump. If so, can you please provide the cost and part number? If not can you please provide a contact where I can purchase the bearings.
Than You
Reply
Hello Joyce. The bearings for the Century Motors 2.0 HP motor model UST1202.are: Shaft End 5270-32 Bearing, 204 Ntn 6204-ll (6204-2rs) Opposite Shaft End 5270-31 Bearing, 203 (Single) - 62032RS
Reply
Hello, the part# on my pump is 7-159988-06. Is this an acceptable replacement pump motor for my unit?
Hi Chris, actually this Century 2.0 HP Round Flange 56J Full Rate EE Motor - B130 would be the perfect match to replace your old motor. Let us know what the model of the pump is that the motor attaches to so we can help you choose a new motor shaft seal or Tune-Up Kit to ensure a leak-free installation.
Reply
Hello, I need to replace my pump motor and was wondering if this one will work? The capacitor is not sitting on top like this one is with my current motor. Current equipment - Hayward Pump M/N-SP3015X20AZ Motor M/N-C48M2N11A3
Thanks!
Hi Craig, some of the newer motors don't have the old capacitor hump on them. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 will be a perfect replacement for your pump. Be sure to add a Tune-Up Kit to your order so you can replace all of the o-rings and the motor shaft seal on your Hayward Super II SP3000 Series pump.
Reply
Need a replacement motor for Hayward super pump. My current motor is pictured below US Motors ASB809 2HP.
Hello Gregg. The Century 2.0 HP Round Flange 56J Up Rate Motor - B230SE is a compatible replacement motor for the U S Motor model ASB809. The Tune Up Kit Hayward Super Pump - GOKIT3 contains the seals and gaskets necessary to complete the motor replacement.
Reply
Is this compatible with the Hayward SPX1615Z1M
Reply
Hello Linda. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible replacement for the Hayward SPX1615Z1M.
Reply
Hi - I need to replace the Century Electric Part 8-177062-40 Fit M56J (see picture please). Will this or another pump work?
Thanks!
Reply
Hello Eric. The Century 1.5 HP Round Flange 56J Dual Speed Full Rate Motor - B2977 is the direct motor replacement for the Century Motors model 8-177062-40. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible motor replacement providing there is no California Title 20 Compliance stipulation. The UST1202 is smaller in diameter and longer than the 8-177062-40. Please check the installation dimensions. The wet end bolt connection points are identical. The V-Green 1.65 HP Round Flange 56J Variable Speed Motor - ECM16CU may be an option. Pump manufacturer/model information is required prior to this recommendation.
Reply
Is this compatible
Hello Dennis. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible motor replacement for the Century Motors model C48M2N111B3. The Tune Up Kit Hayward Super Pump - GOKIT3 contains the shaft seal, seal plate gasket, and diffuser o-ring that should be replaced concurrent with the new motor for your Hayward Super Pump. Attached please find the Hayward Super Pump exploded parts diagram for reference.
Reply
Hello
I have a Hayward SP2615X20 with a AO SMITH 2 HP 56J MODEL K48M2N111 SERIAL 31208FM. Also states on it SP-1615-Z1-MEG.
Its 13 years old and i think its beginning to go. Please advise the replacement motor for correct fit?
Thanks
Hello John. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible motor replacement for the Hayward Super Pump model SP2615X20 with the motor model K48M2N111. The Tune Up Kit Hayward Super Pump - GOKIT3 contains the seals and gaskets necessary to complete the motor replacement.
Reply
Hi,
Is this model a compatible replacement for same model number B130, Part Number 0-159988-06, serial number 03416CHCL010459988 also a 2 HP? Also, what is shipping time?
Thank you,
Mike
Reply
Hi Michael, the correct motor is actually the model 5224X and the average motor orders are delivered between 1-3 business days. If you need the seal kit as well here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist.
Reply
Hi! I am needing to replace a 2 hp motor on a carvin magnum pool pump. Wondering if this motor "Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202" is the correct replacement. I am attaching a pic of my current motor specs.
Thanks!
Hello Elexxa. The Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202 is a compatible motor replacement for the Century Motors model 7-184950-22. The Tune Up Kit Carvin/Jacuzzi Magnum Series - GOKIT14 contains the seals and gaskets necessary for the new motor installation. Attached please find the Jacuzzi Magnum exploded parts diagram for reference.
Reply
do you have in stock? I live in phoenix az1 how fast can it be shipped
Reply
Hi Bruce, yes these are currently in stock and have an approximate 3 business day delivery time. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that should assist you with that.
Reply
Do you have a variable speed pump to replace this:
Century 2.0 HP Round Flange 56J Up Rate Motor - UST1202?
Reply
Hello Harold. The V-Green EVO 2.25 HP Round Flange 56J Variable Speed Motor - EVC225 is a compatible variable speed motor for the Century Motors model UST1202.
Reply
can i replace A O SMITH MOTOR 7 193993 05 1 HP WITH THIS 2 HP MOTOR
Reply
Hello Hugo, upgrading to a 2 HP single speed motor may or may not be wise as with the increased water pressure that could be to much for your filter and or plumbing design per the pools initial pool build specifications. However you would not need to consider or calculate those variables with a variable speed motor such as the model EVQ225. It is also much more energy efficient. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that help assist you with that as well.
Reply
will this pump lline up perfectly with a century hsq125?
Reply
Hello Dick, the correct single speed motor replacement that will align with your motor model HSQ125 is the USQ1102. We also recommend replacing the seals and gaskets when replacing a pool pump motor. Here is our "Finding the Tune-Up Kit for Your Pool Pump" guide that help assist you with that as well.
Reply
Hi currently I have century model K48m2n111 ser#05821chck030003339
Can I replace with this?
Hello, yes, the UST1202 will be the correct replacement for your current motor. You will also need a seal kit for the motor replacement process; you can identify the correct seal kit for your pump by using our Finding the Tune-Up Kit for Your Pool Pump" guide which should assist you with that.
Reply
